Ryobi C358- Manuals

7 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic-ing, use only identical replacement parts. WARNING: SAVE THE...

8 SPEED AND WIRING The no-load speed of this tool is approximately 3,900 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot properly carry a power...

9 FEATURES PRODUCT SPECIFICATIONS n Input.............................. 120V, 60 Hz, AC Only,15 Amps n No Load Speed..............................................3,900/min. n Arbor Diameter ........................................................ 1 in. n Wheel Diameter .................................

10 FEATURES LOCK-ON BUTTON See Figure 3. T h e c u t - o ff m a c h i n e i s e q u i p p e d w i t h a l o c k - o n feature which is convenient when continuous cutting for extended periods of time is required. To engage the lock-on feature, depress switch trigger, push in and hold the lock-on butt...

11 LOOSE PARTS ASSEMBLY UNPACKING This product has been shipped completely assembled. n Carefully lift machine from the carton by the carrying handle and the machine base, and place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and ge...

12 REMOVAL / INSTALLATION OF WHEEL TO REMOVE See Figure 5. n Unplug the cut-off machine. n Push down on machine arm and remove transport chain from hook on motor housing to release machine arm. n Raise machine arm to its full raised position. Be cautious when raising, machine arm is spring loaded. n...

13 Fig. 6 Fig. 7 Fig. 8 ADJUSTABLE FENCE ADJUSTABLE FENCE FENCE SCALE VISE CLAMP ADJUSTABLE FENCE ASSEMBLY ADJUSTABLE FENCE See Figure 6. The adjustable fence is located at the rear of the cut-off machine. As mentioned previously, it is used along with the vise clamp to provide a clamp for holding t...

14 Fig. 9 Fig. 10 QUICK LOCK-RELEASE LEVER WITH THREADS NOT ENGAGED VISE CLAMP VISE CRANK HANDLE VISE SCREW VISE CLAMP VISE CRANK HANDLE QUICK LOCK- RELEASE LEVER WITH THREADS ENGAGED n Using the hex wrench supplied, securely tighten hex head bolts. Return hex wrench to its storage area in base. � n...

15 Fig. 11 CAUTION: Do not start the abrasive cut-off machine without check-ing for interference between the wheel and the machine base support. Damage may result to the wheel if it strikes the machine base support during operation of themachine. � n Tighten the depth stop bolt with the hex wrench p...

18 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, als...

19 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine does not start 1. Power cord not plugged in. 1. Plug in cord. 2. Power cord is damaged. 2. Have the cord replaced at your nearest authorized service center. 3. Circuit breaker is tripped. 3. Reset circuit breaker. 4. Circuit fuse is blown 4. Replace ...

983000-607 10-04 OPERATOR’S MANUAL 14 in. Abrasive Cut-Off Machine C358 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. P...

7 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic-ing, use only identical replacement parts. WARNING: SAVE THE...

8 SPEED AND WIRING The no-load speed of this tool is approximately 3,900 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot properly carry a power...

9 FEATURES PRODUCT SPECIFICATIONS n Input.............................. 120V, 60 Hz, AC Only,15 Amps n No Load Speed..............................................3,900/min. n Arbor Diameter ........................................................ 1 in. n Wheel Diameter .................................

10 FEATURES LOCK-ON BUTTON See Figure 3. T h e c u t - o ff m a c h i n e i s e q u i p p e d w i t h a l o c k - o n feature which is convenient when continuous cutting for extended periods of time is required. To engage the lock-on feature, depress switch trigger, push in and hold the lock-on butt...

11 LOOSE PARTS ASSEMBLY UNPACKING This product has been shipped completely assembled. n Carefully lift machine from the carton by the carrying handle and the machine base, and place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and ge...

12 REMOVAL / INSTALLATION OF WHEEL TO REMOVE See Figure 5. n Unplug the cut-off machine. n Push down on machine arm and remove transport chain from hook on motor housing to release machine arm. n Raise machine arm to its full raised position. Be cautious when raising, machine arm is spring loaded. n...

13 Fig. 6 Fig. 7 Fig. 8 ADJUSTABLE FENCE ADJUSTABLE FENCE FENCE SCALE VISE CLAMP ADJUSTABLE FENCE ASSEMBLY ADJUSTABLE FENCE See Figure 6. The adjustable fence is located at the rear of the cut-off machine. As mentioned previously, it is used along with the vise clamp to provide a clamp for holding t...

14 Fig. 9 Fig. 10 QUICK LOCK-RELEASE LEVER WITH THREADS NOT ENGAGED VISE CLAMP VISE CRANK HANDLE VISE SCREW VISE CLAMP VISE CRANK HANDLE QUICK LOCK- RELEASE LEVER WITH THREADS ENGAGED n Using the hex wrench supplied, securely tighten hex head bolts. Return hex wrench to its storage area in base. � n...

15 Fig. 11 CAUTION: Do not start the abrasive cut-off machine without check-ing for interference between the wheel and the machine base support. Damage may result to the wheel if it strikes the machine base support during operation of themachine. � n Tighten the depth stop bolt with the hex wrench p...

18 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, als...

19 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine does not start 1. Power cord not plugged in. 1. Plug in cord. 2. Power cord is damaged. 2. Have the cord replaced at your nearest authorized service center. 3. Circuit breaker is tripped. 3. Reset circuit breaker. 4. Circuit fuse is blown 4. Replace ...

983000-607 10-04 OPERATOR’S MANUAL 14 in. Abrasive Cut-Off Machine C358 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. P...