Ryobi BGH616- Manuals

7 SyMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service tech-nician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts. WARNING: To avoid ...

8 SPEED AND WIRING The no-load speed of this tool is approximately 3,600 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot properly carry a power...

9 FEATURES PRODUCT SPECIFICATIONS-MODEL BGH616 Wheel Diameter ........................................................... 6 in.Wheel Thickness ...................................................... 3/4 in.Arbor Hole ................................................................ 1/ in.No Load Speed...

10 adjuStable WrenCH Fig. 3 Combination WrenCH (3) 7 mm, 10 mm, and 12 mm PHilliPS SCreWdriVer The following tools (not included) are needed for checking adjustments of your saw or for installing the blade: TOOLS NEEDED LOOSE PARTS The following items are included with your Bench Grinder:  Shield B...

11 MOUNTING SAFETy SHIELD ASSEMBLy See Figure 5.  Fasten the safety shield assemblies to the safety shield brackets using the fastening knob and small washer. NOTE: The slotted part of the safety shield bracket must face towards the grinding wheel guard.  Attach the safety shield assembly and brac...

1 WaSHer CarriaGe bolt WorK reSt aSemblY Fig. 6 Knob Pin ASSEMBLy MOUNTING WORK REST See Figure 6.  Remove the knob, star washer, and washer from the car- riage bolt on the lower portion of wheel guard.  Using the slotted screw, star washer, washer and fasten- ing knob, attach the work rest bracke...

13 WARNING: Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects b...

14 OPERATION Fig. 10 SCreWdriVer ViSe laWn moWer blade SHARPENING TWIST DRILL BITS See Figure 9. Drill bits are best sharpened on a sharpening jig (available at most hardware stores). Begin on one side of the point at the existing angle, then twist the bit while maintaining contact with the grinding...

15 Fig. 1 SCreW(S) GrindinG WHeel outer FlanGe inner FlanGe loCK WaSHer(S) HeX nut(S) WHeel Guard CoVer WHeel nut SPindle SHaFt WARNING: Always disconnect the bench grinder from the power source before performing any assembly or adjustment. Failure to do so could result in accidental starting result...

16 MAINTENANCE Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commu-tators, etc. Consequently, we do not recomme...

ONE WORLD TECHNOLOGIES, INC. 148 Pearman Dairy Road, Anderson, SC 965 Phone 1-800-55-579 www.ryobitools.com 983000-66-8-08 (REV:04) • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to...

7 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts. WARNING: SAVE TH...

8 SPEED AND WIRING The no-load speed of this tool is approximately 3,600 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot properly carry a power...

9 FEATURES PRODUCT SPECIFICATIONS-MODEL BGH616 Wheel Diameter ........................................................... 6 in.Wheel Thickness ...................................................... 3/4 in.Arbor Hole ................................................................ 1/2 in.No Load Spee...

10 ADJUSTABLE WRENCH Fig. 3 COMBINATION WRENCH (3) 7 mm, 10 mm, and 12 mm PHILLIPS SCREWDRIVER The following tools (not included) are needed for checking adjustments of your saw or for installing the blade: TOOLS NEEDED LOOSE PARTS The following items are included with your Bench Grinder: n Shield B...

11 MOUNTING SAFETY SHIELD ASSEMBLY See Figure 5. n Fasten the safety shield assemblies to the safety shield brackets using the fastening knob and small washer. NOTE: The slotted part of the safety shield bracket must face towards the grinding wheel guard. n Attach the safety shield assembly and brac...

12 WASHER CARRIAGE BOLT WORK REST ASEMBLY Fig. 6 KNOB PIN ASSEMBLY MOUNTING WORK REST See Figure 6. n Remove the knob, star washer, and washer from the car- riage bolt on the lower portion of wheel guard. n Using the slotted screw, star washer, washer and fasten- ing knob, attach the work rest brack...

13 WARNING: Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second issufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects be...

14 OPERATION Fig. 10 SCREWDRIVER VISE LAWN MOWER BLADE SHARPENING TWIST DRILL BITS See Figure 9. Drill bits are best sharpened on a sharpening jig (available at most hardware stores). Begin on one side of the point at the existing angle, then twist the bit while maintaining contact with the grinding...

15 Fig. 12 SCREW(S) GRINDING WHEEL OUTER FLANGE INNER FLANGE LOCK WASHER(S) HEX NUT(S) WHEEL GUARD COVER WHEEL NUT SPINDLE SHAFT WARNING: Always disconnect the bench grinder from the power source before performing any assembly or adjustment. Failure to do so could result in accidental starting resul...

16 MAINTENANCE Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commu-tators, etc. Consequently, we do not recomme...

RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com 983000-626 3-05 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your neares...