Ryobi BD4600- Manuals

Page 3 - GENERAL SAFETy RULES

3 GENERAL SAFETy RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. REAd ALL INSTRUCTIONSWORK AREA  KNOW yOUR POWER TOOL. Read the operator’s manual carefully. Learn the application...

Page 5 - SyMBOLS; SyMBOL

5 Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alte...

Page 6 - SERVICE; SAVE THESE INSTRUCTIONS

6 SyMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. dANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, ...

Page 7 - SPEEd ANd WIRING; GROUNdING INSTRUCTIONS; ELECTRICAL; EXTENSION CORdS; ELECTRICAL CONNECTION

7 SPEEd ANd WIRING The belt speed of this tool is approximately 1,900 SFM. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot properly carry a power to...

Page 8 - GLOSSARy OF TERMS

8 GLOSSARy OF TERMS Non-Through Cuts Any cutting operation where the blade does not extend completely through the thickness of the workpiece. Push Blocks (for jointer planers) Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid helps keep the operator'...

Page 9 - FEATURES

9 FEATURES Fig. PROdUCT SPECIFICATIONS Belt Size ........................................................... 4 in. x 36 in. Belt Speed ......................................................... 1,9 00 SFM Belt Tilt ..................................................................... 0°- 90° Disc Siz...

Page 10 - POWER SWITCH; LOCKING THE SWITCH; WARNING; WARNING

10 FEATURES POWER SWITCH See Figure 3. The belt/disc sander is eq uipped with a power switch that has a built-in locking feature. This feature is intended to prevent unauthorized and possible hazardous use by chil-dren and others. TO TURN THE BELT/dISC SANdER ON:  With the switch key inserted into ...

Page 11 - ASSEMBLy; UNPACKING; LOOSE PARTS

11 ASSEMBLy UNPACKING This product requires assembly.  Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the tool carefully to make sure no breakage or damage occurred during shipping.  Do not discard the packing...

Page 13 - ASSEMBLING WORK SUPPORT

13 4 x36 4 x36 ASSEMBLy ASSEMBLING WORK SUPPORT See Figure 10.  Place the work support over the holes in the side of the tool housing.  Using a hex key, fasten in place with the washers and socket head screws. MOUNTING BELT/dISC SANdER TO WORK-BENCH See Figure 11. If the belt/disc sander is to be ...

Page 14 - OPERATION; APPLICATIONS

14 0 15 45 OPERATION Fig. 13 tABle loCK KnoB WARNING: Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. ...

Page 15 - HORIZONTAL ANd VERTICAL SANdING

15 4 x36 Fig. 16 4 x36 WorK SuPPort WorKPieCe Fig. 17 WorKPieCe OPERATION HORIZONTAL ANd VERTICAL SANdING See Figure 15. The belt/disc sander can sand both vertically and horizontally. Depending on the workpiece, the work support can be used with either the horizontal or vertical sanding operation. ...

Page 16 - AdJUSTMENTS

16 4 x36 AdJUSTMENTS WARNING : Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the OFF ( O ) position. Failure to heed this warning could result in serious personal injury. AdJUSTING THE BELT TRACKING See Figure 19.  Plug in belt/disc san...

Page 17 - MAINTENANCE; LUBRICATION

17 Fig. 1 PHilliPS HeAd SCreWS SAndinG Belt HeX HeAd Set SCreW driVe Belt driVe PulleY Motor PulleY MAINTENANCE Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grind...

Page 18 - • MODEL NUMBER; OPERATOR’S MANUAL

18 ONE WORLd TECHNOLOGIES, INC. 148 Pearman Dairy Road, Anderson, SC 965 Phone 1-800-55-579 www.ryobitools.com • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinen...