Ryobi AIRgrip ProCross ELL0006- Manuals

Page 3 - gENERAL SAfETY RULES

3 gENERAL SAfETY RULES WARNINg! READ AND UNDERSTAND ALL INSTRUCTIONS. Fail- ure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. CAUTION: Use of controls or adjustments or performance of pro-cedures other than those specified herein may resu...

Page 4 - SYMBOLS; SYMBOL

4 SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Min...

Page 5 - SERvICE; SAvE THESE INSTRUCTIONS

5 SERvICE This unit has no serviceable parts. If the unit fails due to normal wear and tear within two years of purchase, return with original receipt for a replacement unit at no charge. Call 1-800-55-579 for your nearest AUTHORIZED SERvICE CENTER . WARNINg: To avoid serious personal injury, do not...

Page 6 - fEATURES; PRODUCT SPECIfICATIONS

6 fEATURES Fig. 1 PRODUCT SPECIfICATIONS Recommended Use.....................................................................................................................................................IndoorsAIRgrip Power Supply ......................................................................

Page 8 - ASSEMBLY; UNPACKINg; OPERATION; APPLICATIONS

8 ASSEMBLY UNPACKINg This product has been shipped completely assembled.  Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the product carefully to make sure no breakage or damage occurred during shipping.  D...

Page 9 - TURNINg THE vACUUM BASE ON/Off

9 OPERATION  Rotate the laser lens housing until the battery compart-ment comes into view.  Remove battery cover plate.  Install two AA batteries according to polarity indicators (+ or −) inside the battery compartment.  Reinstall the battery cover plate. NOTE: Remove the batteries from both the...

Page 10 - ROUgH SURfACE ADAPTOR

10 OPERATION ROUgH SURfACE ADAPTOR See Figure 7. By using the rough surface adaptor, you can use the AIRgrip feature to position the unit on many non-smooth surfaces, including brick and painted cinder block. NOTE: The AIRgrip feature cannot be used with stucco or unpainted cinder block.  Place the...

Page 11 - USINg A TRIPOD

11 OPERATION Fig. 11 USINg A TRIPOD See Figure 10. The laser level has a 5/8 in.-0 threaded fitting for attaching to a tripod base (not included). This method of mounting is ideal for leveling kitchen cabinets, countertops, window framing, and more.If a 1/4 in. tripod fitting is needed, thread the a...

Page 12 - MAINTENANCE; gENERAL MAINTENANCE

1 MODEL NO. ELL0006 WAVE LENGTH: 630-670 NM MAX. POWER OUTPUT < 5MW CLASS IIIA LASER PRODUCT LASER RADIATION- AVOID DIRECT EYE EXPOSURE Complies with 21 CFR parts 1040.10 and 1040.11 Rayonnement laser - éviter le contact oculaire direct Lire les instructions du manuel. PELIGRO Radiación láser - E...

Page 13 - TROUBLESHOOTINg; Problem

13 TROUBLESHOOTINg Problem Possible Cause Solution Vacuum not running. Batteries are low.Power is turned off. Replace batteries.Press on/off button. Laser line projection is weak. Batteries are low. Replace batteries. Laser line is hard to see. Light in area is too bright. Line is being projected be...

Page 14 - OPERATOR’S MANUAL; AIRgrip; • SERVICE; • MODEL NUMBER

ONE WORLD TECHNOLOgIES, INC. 148 Pearman Dairy Road Anderson, SC 965 Phone 1-800-55-579 www.ryobitools.com OPERATOR’S MANUAL AIRgrip ™ ProCross ™ LASER LEvEL SELf-LEvELINg ELL0006 983000-9746-19-07 (REV:0) • SERVICE This product has no serviceable parts. If unit fails due to normal wear and tear wit...

Ryobi AIRgrip ProCross ELL0006- Manuals

Manuals:

User Manual Ryobi AIRgrip ProCross ELL0006

Summary

Ryobi Manuals