Ryobi AG401- Manuals

Page 5 Inspect for and remove all foreign objects fromworkpiece before grinding. Following this rule will reduce the risk of serious personal injury. Drugs, Alcohol, Medication. Do not operate tool while under the influence of drugs, alcohol, or anymedication. Following this rule will reduce the ris...

Page 6 SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current --- Direct Current Type or a characteristic of current n 0 No Load Speed Rotational speed, at no load .../min R...

Page 7 With the exception of the side handle and grinding wheel,your angle grinder has been shipped completely assembled. Carefully remove the grinder and accessories from thebox. Make sure that all items listed in the packing list areincluded. Inspect grinder carefully to make sure no breakage orda...

Page 8 KNOW YOUR ANGLE GRINDER Before attempting to use your grinder, familiarize yourselfwith all operating features and safety requirements. See Figure 1. Make sure all grinding wheels and recommended accessoriesare in accordance with listed specifications for this tool. Forexample, do not use gri...

Page 9 4’’ Grinder WARNING: Your grinder should never be connected to power supplywhen you are assembling parts, making adjustments,installing or removing grinding wheels, or when not in use.Disconnecting your grinder will prevent accidental startingthat could cause serious injury. INSTALLING THE SI...

Page 10 Fig. 4 INCORRECT LOCATION OF GUARD ADJUSTMENTS CORRECT LOCATION OF GUARD IS BETWEEN POINTS A AND B WARNING: Do not attempt to operate this tool until you have readthoroughly and understand completely all instructions,safety rules, etc. contained in this manual. Failure tocomply can result in...

Page 11 Fig. 8 SWITCH BUTTON ON 5 ° TO 15 ° OPERATION 15 degrees and continuously moving at a steady, consistentpace. Move the grinder back and forth or up and down overthe work area. Keep the grinder moving so that an excessiveamount of material is not removed from one area. If thegrinder is held i...

Page 12 WRENCH CLAMP NUT GRINDING WHEEL GUARD DISC FLANGE CLAMP SCREW TO LOOSEN TO TIGHTEN FLAT(S) SPINDLE LOCK BUTTON SPINDLE BEARING CAP Fig. 9 WARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause productdamage. MAINTENANCE GUARD R...

OPERATOR'S MANUAL4 in. (100 mm) Angle GrinderModel AG401 / Double Insulated 983000-031 5-05 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622 Phone 1-800-525-2579 www.ryobitools.com EXTENSION CORD CAUTION When using a power tool at a considerab...

Page 5 Inspect for and remove all foreign objects fromworkpiece before grinding. Following this rule will reduce the risk of serious personal injury. Drugs, Alcohol, Medication. Do not operate tool while under the influence of drugs, alcohol, or anymedication. Following this rule will reduce the ris...

Page 6 SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current --- Direct Current Type or a characteristic of current n 0 No Load Speed Rotational speed, at no load .../min R...

Page 7 With the exception of the side handle and grinding wheel,your angle grinder has been shipped completely assembled. Carefully remove the grinder and accessories from thebox. Make sure that all items listed in the packing list areincluded. Inspect grinder carefully to make sure no breakage orda...

Page 8 KNOW YOUR ANGLE GRINDER Before attempting to use your grinder, familiarize yourselfwith all operating features and safety requirements. See Figure 1. Make sure all grinding wheels and recommended accessoriesare in accordance with listed specifications for this tool. Forexample, do not use gri...

Page 9 4’’ Grinder WARNING: Your grinder should never be connected to power supplywhen you are assembling parts, making adjustments,installing or removing grinding wheels, or when not in use.Disconnecting your grinder will prevent accidental startingthat could cause serious injury. INSTALLING THE SI...

Page 10 Fig. 4 INCORRECT LOCATION OF GUARD ADJUSTMENTS CORRECT LOCATION OF GUARD IS BETWEEN POINTS A AND B WARNING: Do not attempt to operate this tool until you have readthoroughly and understand completely all instructions,safety rules, etc. contained in this manual. Failure tocomply can result in...

Page 11 Fig. 8 SWITCH BUTTON ON 5 ° TO 15 ° OPERATION 15 degrees and continuously moving at a steady, consistentpace. Move the grinder back and forth or up and down overthe work area. Keep the grinder moving so that an excessiveamount of material is not removed from one area. If thegrinder is held i...

Page 12 WRENCH CLAMP NUT GRINDING WHEEL GUARD DISC FLANGE CLAMP SCREW TO LOOSEN TO TIGHTEN FLAT(S) SPINDLE LOCK BUTTON SPINDLE BEARING CAP Fig. 9 WARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause productdamage. MAINTENANCE GUARD R...

OPERATOR'S MANUAL4 in. (100 mm) Angle GrinderModel AG401 / Double Insulated 983000-031 5-05 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622 Phone 1-800-525-2579 www.ryobitools.com EXTENSION CORD CAUTION When using a power tool at a considerab...