Ryobi 4950300- Manuals

Page 2 - RULES FOR SAFE OPERATION

Page 2 ■ READ THESE INSTRUCTIONS THOROUGHLYbefore assembling or using this router mounting kit. ■ R E A D THE INSTRUCTIONS AND RULES OF SAFE OPERATION FOR THE BT3000 TABLESAW before operating your saw with this kit. ■ K E E P ASSEMBLY AREA AND WORK AREA CLEAN. Cluttered areas and benches invite acci...

Page 3 - UNPACKING

Page 3 Your new Router Mounting kit includes one mountingplate, two guide fences with guide blocks, a guard/dustcover with pivot assembly, five throat plates, plus thenecessary brackets and connecting hardware requiredto mount a Ryobi Router to the accessory table of yourBT3000 table saw. INTRODUCTI...

Page 4 - LIST OF LOOSE PARTS; LOOSE PARTS

Page 4 DESCRIPTION QUANTITY DESCRIPTION QUANTITY LIST OF LOOSE PARTS Your #4950300 Router Mounting Kit includes the following parts: Fig. 1 GUIDE FENCE WITH GUIDE BLOCK 1/2 in. KNOB BOLTS 5/16 in. WASHERS THROAT PLATES ROUTER MOUNTING PLATE TABLE CLAMPING BRACKET 5/16 in. T-NUTS 3/4 in. KNOB BOLT SP...

Page 5 - IMPORTANT; ROUTER MOUNTING

Page 5 Read these instructions completely before beginning assembly of this kit. WARNING: The saw's motor cord must be disconnected fromthe receptacle on the saw when using this kit. Thepower cord of the router must be plugged into thereceptacle on the saw. The saw's master switchmust be used to tur...

Page 6 - TO INSTALL GUIDE FENCE BRACKETS:; T O A S S E M B L E R O U T E R S W I T H 2 - H O L E

Page 6 ROUTER MOUNTING Fig. 4 GUARD/DUST COVER WITH PIVOT ASSEMBLY KNOB NUT FLATS ON POST POST KNOB BOLTS 5/16 in. WASHERS GUIDE FENCE BRACKET RIP FENCE T-NUTS CARRIAGE BOLT (NOT SHOWN) SPACER Fig. 5 ROUTER MOUNTING SCREWS ROUTER MOUNTING PLATE ROUTER WITH 2–HOLE PATTERN SUBBASE ROUTER BASE TO INSTA...

Page 7 - T O A S S E M B L E R O U T E R S W I T H 3 - H O L E

Page 7 Fig. 6 Fig. 7 Fig. 8 ROUTER MOUNTING T O A S S E M B L E R O U T E R S W I T H 2 - H O L E PATTERN TO ROUTER MOUNTING PLATE(cont'd): See Figures 5 and 6. ■ Secure the router mounting plate to the router usingtwo 5/16-18 x 3/4 in. bolts provided in the routermounting kit. ■ Properly installed,...

Page 8 - T O A S S E M B L E R O U T E R S W I T H 4 - H O L E

Page 8 Fig. 9 Fig. 10 ROUTER MOUNTING 4–HOLE ROUTER WITH MOUNTING PLATE ATTACHED ROUTER MOUNTING SCREWS FRONT OF ROUTER ROUTER MOUNTING PLATE ROUTER WITH 4–HOLE PATTERN T O A S S E M B L E R O U T E R S W I T H 4 - H O L E PATTERN TO ROUTER MOUNTING PLATE: See Figures 9 and 10. Note: For Ryobi route...

Page 9 - TO ASSEMBLE TABLE CLAMPING BRACKET:

Page 9 Fig.11 ROUTER MOUNTING TABLE CLAMPING BRACKET SHOWN COMPLETELY ASSEMBLED ACCESSORY TABLE TABLE CLAMPING BRACKET T-NUT REAR RAIL 5/16 in. WASHER KNOB BOLT END PLUG Fig.12 SLOT THROAT PLATE ACCESSORY TABLE #1/4-20 SCREWS (PROVIDED) ROUTER WITH MOUNTING PLATE ATTACHED INSTALLING ROUTER BIT AND T...

Page 10 - FINAL PREPARATION FOR OPERATION

Page 10 Fig. 13 DIRECTION OF FEED IS FROM RIGHT TO LEFT AGAINST SHARP EDGES OF ROTATING BIT ROUTER KIT SHOWN COMPLETELY ASSEMBLED FINAL ASSEMBLY: After the router mounting parts have been assembled,your setup should be similar to Figure 13. ■ Compare your setup and make any necessaryadjustments. ■ R...

Page 11 - NOTES

Page 13 - REPLACEMENT PARTS; PARTS LIST

Page 15 REPLACEMENT PARTS Now that you have purchased your Router Mounting Kit, should a need ever exist for repair parts or service,simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts whenyou call or visit. PARTS LIST KEY PART NO NUMBER DESCRIPTION QU...

Page 14 - RYOBI TECHNOLOGIES INC.

RYOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com 612547-852 OPERATOR'S MANUAL #4950300 ROUTER MOUNTING KIT(FOR USE WITH THE BT3000 TABLE SAW)

Manuals:

User Manual Ryobi 4950300

Summary

Ryobi Manuals