Rotel RA-1070 - Manuals - manualsarea.com

Page 2 - CAUTION; RISK OF ELECTRIC SHOCK

2 RA-1070 Stereo Integrated Amplifier CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADEOF PLUG TO WIDE SLOT. INSERT FULLY. APPLICABLE FOR USA, CANADA OR WHEREAPPROVED FOR THE USAGE ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHEDANS LA BORNE CORRESPONDANT...

Page 3 - Figure 1: Controls and Connections

3 Figure 1: Controls and Connections English I N T E G R AT E D S T E R E O A M P L I F I E R R A - 1 0 7 0 V O L U M E P H O N E S C O N T O U R O F F H L H L- 1 L- 2 S P E A K E R S A B A + B O F F P R O T E C T I O N P OW E R R E C O R D I N G L I S T E N I N G D V D / V I D E O T U N E R D V D /...

Page 4 - Figure 4: Speaker Output Connection

4 Figure 3: Phono and Line Inputs; Recorder Input/Output RA-1070 Stereo Integrated Amplifier R L GND PH0NO ROTEL RA-1070 RECORDER INPUT OUTPUT L R CD PLAYER OUTPUT R L RIGHT AUX 1 DVD /VIDEO TUNER CD PHONO TAPE 2 IN OUT TAPE 1 IN OUT LEFT 1 2 PRE OUT RIGHT AUX 2 LEFT RIGHT LEFT IN EXT REM IR OUT 12V...

Page 5 - About Rotel

5 English About Rotel A family whose passionate interest in musicled them to manufacture high fidelity compo-nents of uncompromising quality founded Rotel40 years ago. Over the years that passionhas remained undiminished and the goal ofproviding exceptional value for audiophilesand music lovers rega...

Page 6 - RR-969 Remote Control; Remote Sensor

6 The RA-1070 printed circuit boards (PCB) aredesigned with Symmetrical Circuit Traces. Thisinsures that the precise timing of the music ismaintained and faithfully recreated. The RA-1070 circuitry uses metal film resistors andpolystyrene or polypropylene capacitors in im-portant signal paths. All a...

Page 7 - AC Power and Control

7 English AC Power and Control AC Power Input The RA-1070 uses a moderate amount ofpower. However there are two auxiliary poweroutlets on the back of the unit, which can beused to supply up to 200 watts of power forother components. Consequently, the RA-1070should be plugged directly into a 2-pin po...

Page 8 - Preamp Outputs; IR Inputs and Outputs; 2 Volt Trigger Outlet

8 Preamp Outputs The RA-1070 has two sets of preamp outputs.The signal from the source selected with theListening Selector buttons is always availablefrom these outputs. Typically these outputs areused to provide a signal to another integratedamplifier or power amplifier, which is usedto drive remot...

Page 9 - Computer I/O Connector

9 English Computer I/O Connector The RA-1070 can be operated from a per-sonal computer running audio system controlsoftware from third-party developers. This con-trol is accomplished by sending the operat-ing codes normally sent by the RR-969 remotecontrol over a hard-wired network connec-tion from ...

Page 10 - FL Display Control

10 RA-1070 Stereo Integrated Amplifier FL Display Control Turning FL Display On/Off To turn the front panel FL Display on or off,press the Display button on the RR-969. When the display is set to off, the ListeningSelector Display and Recording Selector Dis-play will light for 5 seconds when a new s...

Page 11 - Specifications

11 Specifications Continuous Power Output 100 watts/ch (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz ) < 0.03% at rated power,1/2 power or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.05% at rated power,1/2 power or 1 watt Frequency Response Line level inp...