Rosewill RNWB-11001 - Manuals

300M Wireless N Router RNX-N300RT User Manual • Do not install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. • Connect ONLY suitable accessories to the device. • Do not open the device or unit. Opening or removing covers can expose you t...

300M Wireless N Router RNX-N300RT User Manual Contents Package Contents.................................................................................................................... 8 Chapter 1 Introduction ..........................................................................................

300M Wireless N Router RNX-N300RT User Manual Package Contents The following items should be found in your package: • RNX-N300RT 300M Wireless N Router • Power Adapter for RNX-N300RT 300M Wireless N Router • Quick Installation Guide • Resource CD for RNX-N300RT 300M Wireless N Router including: ¾ Th...

300M Wireless N Router RNX-N300RT User Manual Chapter 1 Introduction Congratulations on your purchase of Rosewill’s RNX-N300RT Wireless N Router. RNX-N300RT 300M Wireless N Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. Powered by 2x2 MIMO technology, the 300M Wireless N Rout...

300M Wireless N Router RNX-N300RT User Manual ¾ One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX. ¾ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security. ¾ Shares data and Internet access for users, support...

300M Wireless N Router RNX-N300RT User Manual 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 Front Panel sketch The Router’s LEDs and the WPS/Reset button are located on the front panel (View from left to right). -11-

300M Wireless N Router RNX-N300RT User Manual Name Status Indication Off Power is off. Power On Power is on. On The Router is initializing. Flashing The Router is working properly. System Off The Router has a system error. Off The Wireless function is disabled. WLAN Flashing The Wireless function is...

300M Wireless N Router RNX-N300RT User Manual 1.3.2 The Rear Panel Figure 1-2 Rear Panel sketch The following parts are located on the rear panel (View from left to right). ¾ POWER: The Power socket is where you will connect the power adapter. Please use the power adapter provided with this RNX-N300...

300M Wireless N Router RNX-N300RT User Manual Chapter 2 Connecting the Router 2.1 System Requirements ¾ Broadband Internet Access Service (DSL/Cable/Ethernet) ¾ One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.) ¾ PCs with a w...

300M Wireless N Router RNX-N300RT User Manual 5. Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1. 6. Connect the power adapter to the power socket on the Router, and the other end into an electrical outlet. The Router will start to work automatically. 7. Power on your ...

300M Wireless N Router RNX-N300RT User Manual Chapter 3 Quick Installation Guide This chapter will show you how to configure the basic functions of your RNX-N300RT using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the RNX-N300RT is 192.168.1.1. And the defau...

300M Wireless N Router RNX-N300RT User Manual Figure 3-1 Success result of Ping command ¾ If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the Router is failed. Figure 3-2 Failure result of Ping command -17-

300M Wireless N Router RNX-N300RT User Manual Please check the connection following these steps: 1. Is the connection between your PC and the Router correct? ) Note: The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should be lit. 2. Is the TCP/IP configurat...

300M Wireless N Router RNX-N300RT User Manual Step 3. Click on Quick Setup Step 4. Click Next when sees this window -19-

300M Wireless N Router RNX-N300RT User Manual Step 5. Click Auto-Detect in this window as RNX-N300RT will detect and select for you connection option. Step 6. Entering your connection information in the next step. You will need to verify with your ISP. PPPoE : Dynamic IP : You do not need to enter a...

300M Wireless N Router RNX-N300RT User Manual Step 7. You will need to set up your wireless signal in this step. Step 8. Click Finish and you are ready! -21-

300M Wireless N Router RNX-N300RT User Manual 3.2.2 Quick Installation Guide – Detail and Explanation: 1. To access the configuration utility, open a web-browser and type in the default address http://192.168.1.1 in the address field of the browser. Figure 3-3 Log in the Router After a moment, a log...

300M Wireless N Router RNX-N300RT User Manual Figure 3-5 Quick Setup 3. Click Next , and then WAN Connection Type page will appear, shown in Figure 3-6. Figure 3-6 WAN Connection Type The Router provides Auto-Detect function and supports three popular ways PPPoE , Dynamic IP and Static IP to connect...

300M Wireless N Router RNX-N300RT User Manual Figure 3-7 Quick Setup - PPPoE ¾ User Name / Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP. 2) If the connection type detected is Dynam...

300M Wireless N Router RNX-N300RT User Manual 5. Click Next to continue, the Wireless settings page will appear as shown in Figure 3-9. Figure 3-9 Quick Setup – Wireless ¾ Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ¾ SSID - Enter a value of up to 32 chara...

300M Wireless N Router RNX-N300RT User Manual Figure 3-10 Quick Setup - Finish If there are something changed on the Wireless page, you will see the Finish page as shown in Figure 3-11. Click the Reboot button to make your wireless configuration to take effect and finish the Quick Setup . Figure 3-1...

300M Wireless N Router RNX-N300RT User Manual Chapter 4 Configuring the Router This chapter will show each Web page's key functions and the configuration way. 4.1 Functions Page After your successful login, you will see the fourteen main functions on the left of the Web-based utility. On the right s...

300M Wireless N Router RNX-N300RT User Manual Figure 4-2 Router Status 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." -29-

300M Wireless N Router RNX-N300RT User Manual 4.4 WPS Setup This section will guide you to add a new wireless device to an existing network quickly by using the WPS (Wifi Protect Setup) function. a) Choose menu “ WPS ”, you will see the next screen (shown in Figure 4-3 ). Figure 4-3 WPS ¾ WPS Status...

300M Wireless N Router RNX-N300RT User Manual ¾ Add device - You can add a new device to the existing network manually by clicking this button. b) To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and R...

300M Wireless N Router RNX-N300RT User Manual The WPS Configuration Screen of Wireless Adapter Method Two: Step 1: Press the WPS button on the front panel of the Router. Step 2: For the configuration of the wireless adapter, please choose “ Push the button on my access point ” in the configuration u...

300M Wireless N Router RNX-N300RT User Manual Step 4: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter 4.4.2 By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to t...

300M Wireless N Router RNX-N300RT User Manual The WPS Configuration Screen of Wireless Adapter ) Note: The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 4-3. c) You will see the following screen when the new device successfully connected to the ne...

300M Wireless N Router RNX-N300RT User Manual 2) The WPS function cannot be configured if the Wireless Function of the Router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.5 Network Figure 4-5 Network menu There are three submenus under the Network menu...

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) If you change the IP Address of LAN, you must use the new IP Address to log in the Router. 2) If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP server will change accordingly at the same time ， while ...

300M Wireless N Router RNX-N300RT User Manual Figure 4-8 WAN - Static IP ¾ IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ¾ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. ¾ Default Gateway - (Optional...

300M Wireless N Router RNX-N300RT User Manual the number of minutes you want to have elapsed before your Internet access disconnects. ¾ Connect Automatically - The connection can be re-established automatically when it was down. ¾ Time-based Connecting - The connection will only be established in th...

300M Wireless N Router RNX-N300RT User Manual Figure 4-10 PPPoE Advanced Settings ¾ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ¾ Service Name/AC Name - The service name and AC (Access...

300M Wireless N Router RNX-N300RT User Manual 4. If your ISP provides BigPond Cable (or Heart Beat Signal) connection, please select BigPond Cable . And you should enter the following parameters (Figure 4-11): Figure 4-11 WAN ¾ User Name/Password - Enter the User Name and Password provided by your I...

300M Wireless N Router RNX-N300RT User Manual Figure 4-12 WAN ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click th...

300M Wireless N Router RNX-N300RT User Manual Figure 4-13 PPTP Settings ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain nam...

300M Wireless N Router RNX-N300RT User Manual ¾ Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity ( Max Idle Time ). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Rout...

300M Wireless N Router RNX-N300RT User Manual z Static IP - Connections which use static IP address assignment. The Router can not detect PPTP/L2TP/BigPond connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. 4.5.3 MAC Clone Choose men...

300M Wireless N Router RNX-N300RT User Manual 4.6 Wireless Figure 4-15 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-15): Wireless Settings , Wireless Security, Wireless MAC Filtering, Wireless Advanced and Wireless Statistics. Click any of them, and you will be ab...

300M Wireless N Router RNX-N300RT User Manual Figure 4-16 Wireless Settings ¾ SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set ...

300M Wireless N Router RNX-N300RT User Manual Note Dialog ) Note: Limited by local law regulations, version for North America does not have region selection option. ¾ Channel - This field determines which operating frequency will be used. The default channel is set to Auto. so the AP will choose the...

300M Wireless N Router RNX-N300RT User Manual ¾ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. ¾ Enable SSID Broadcast - When wireless clients survey the local area for wireless networks to associate with, they will dete...

300M Wireless N Router RNX-N300RT User Manual ¾ WEP Index - This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).It indicates the index of the WEP key. ¾ Auth Type - This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).It indicates the authorization type of the Ro...

300M Wireless N Router RNX-N300RT User Manual ¾ Disable Security - If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security. ¾ WEP - It is based on the IEEE 802.11 standard. If you check this radio but...

300M Wireless N Router RNX-N300RT User Manual ¾ WPA /WPA2-Enterprise - It’s based on Radius Server. • Version - you can choose the version of the WPA security on the pull-down list. The default setting is Automatic , which can select WPA ( Wi-Fi Protected Access) or WPA2 ( WPA version 2) automatical...

300M Wireless N Router RNX-N300RT User Manual encryption, you will find a notice in red as shown in Figure 4-21. Figure 4-21 • PSK Passphrase - You can enter a Passphrase between 8 and 63 characters. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30...

300M Wireless N Router RNX-N300RT User Manual ¾ Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The " Add or Modify Wireless MAC Address Filtering entry " page will appear, shown in Figure 4-23: Figure 4-23...

300M Wireless N Router RNX-N300RT User Manual Figure 4-24 Wireless Advanced ¾ Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾ Beacon Interval - Enter a value between 20-1000...

300M Wireless N Router RNX-N300RT User Manual Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. ¾ Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended. ¾ Enable ...

300M Wireless N Router RNX-N300RT User Manual ¾ Sent Packets - Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond o...

300M Wireless N Router RNX-N300RT User Manual Figure 4-27 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾ Start IP Address - Specify an IP address for...

300M Wireless N Router RNX-N300RT User Manual ¾ Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers. ) Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically&#...

300M Wireless N Router RNX-N300RT User Manual Figure 4-29 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry, either Enabled or Disabl...

300M Wireless N Router RNX-N300RT User Manual Click the Enable/Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 4.8 Forwarding Figure 4-3...

300M Wireless N Router RNX-N300RT User Manual Figure 4-33 Add or Modify a Virtual Server Entry ) Note: If your computer or server has more than one type of available service, please select another service, and enter the same IP Address for that computer or server. To modify or delete an existing ent...

300M Wireless N Router RNX-N300RT User Manual 2. Select a common application from the Common Applications drop-down list, then the Trigger Port field and the Incoming Ports field will be automatically filled. If the Common Applications do not have the application you need, enter the Trigger Port and...

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) When the trigger connection is released, the corresponding opening ports will be closed. 2) Each rule is allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused. 3) Incoming Port R...

300M Wireless N Router RNX-N300RT User Manual 4.9.1 Basic Security Choose menu “ Security → Basic Security ”, you can configure the basic security in the screen as shown in Figure 4-39. Figure 4-39 Basic Security ¾ Firewall - A firewall protects your network from the outside world. Here you can enab...

300M Wireless N Router RNX-N300RT User Manual Figure 4-40 Advanced Security ¾ Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The...

300M Wireless N Router RNX-N300RT User Manual ¾ UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately. ¾ Enable TCP-SYN-FLOOD Attack...

300M Wireless N Router RNX-N300RT User Manual By default, the radio button “ All the PCs on the LAN are allowed to access the Router's Web-Based Utility ” is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router's Web-Based Utility locally from inside t...

300M Wireless N Router RNX-N300RT User Manual ¾ Remote Management IP Address - This is the current address you will use when accessing your Router from the Internet. This function is disabled when the IP address is set to the default value of 0.0.0.0. To enable this function change 0.0.0.0 to a vali...

300M Wireless N Router RNX-N300RT User Manual the screen as shown in Figure 4-44. Figure 4-44 Access Control Rule Management ¾ Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. ¾ Rule Name - Here displa...

300M Wireless N Router RNX-N300RT User Manual 3. Select a host from the Host drop-down list or choose “ Click Here To Add New Host List ”. 4. Select a target from the Target drop-sown list or choose “ Click Here To Add New Target List ”. 5. Select a schedule from the Schedule drop-down list or choos...

300M Wireless N Router RNX-N300RT User Manual Figure 4-46 Host Settings ¾ Host Description - Here displays the description of the host and this description is unique. ¾ Information - Here displays the information about the host. It can be IP or MAC. ¾ Modify - To modify or delete an existing entry. ...

300M Wireless N Router RNX-N300RT User Manual Figure 4-47 Add or Modify a Host Entry Figure 4-48 Add or Modify a Host Entry For example : If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click Add New... butt...

300M Wireless N Router RNX-N300RT User Manual Figure 4-49 Target Settings ¾ Target Description - Here displays the description about the target and this description is unique. ¾ Information - The target can be an IP address, a port, or a domain name. ¾ Modify - To modify or delete an existing entry....

300M Wireless N Router RNX-N300RT User Manual Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-50 Add or Modify an Access Target Entry Figure 4-51 Add or Modify an Access Target Entry For example : If you desire to restrict the internet...

300M Wireless N Router RNX-N300RT User Manual 4. In Domain Name field, enter www.google.com. 5. Click Save to complete the settings. Then you will go back to the Target Settings page and see the following list, 4.10.4 Schedule Choose menu “ Access Control → Schedule ”, you can view and set a Schedul...

300M Wireless N Router RNX-N300RT User Manual 5. Click Save to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-53 Advanced Schedule Settings For...

300M Wireless N Router RNX-N300RT User Manual 4.11 Advanced Routing Figure 4-54 Advanced Routing There are two submenus under the Advanced Routing menu as shown in Figure 4-54: Static Routing List and System Routing Table . Click any of them, and you will be able to configure the corresponding funct...

300M Wireless N Router RNX-N300RT User Manual Figure 4-56 Add or Modify a Static Route Entry 2. Enter the following data. ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The Subnet Mask determines ...

300M Wireless N Router RNX-N300RT User Manual views all of the valid route entries in use. The Destination IP address, Subnet Mask, Gateway, and Interface will be displayed for each entry. Figure 4-57 System Routing Table ¾ Destination Network - The Destination Network is the address of the network ...

300M Wireless N Router RNX-N300RT User Manual Figure 4-59 Bandwidth Control Settings ) Note: For optimal control of the bandwidth, please select the right bandwidth type and ask your ISP for the total bandwidth of the egress and ingress. 4.12.2 Rules List Choose menu “ Bandwidth Control → Rules List...

300M Wireless N Router RNX-N300RT User Manual Step 2: Enter the information like the screen shown below. Figure 4-61 Bandwidth Control Rule Settings Step 3: Click the Save button. 4.13 IP& MAC Binding Settings Figure 4-62 the IP & MAC Binding menu There are two submenus under the IP &MAC...

300M Wireless N Router RNX-N300RT User Manual Figure 4-63 Binding Settings ¾ MAC Address - The MAC address of the controlled computer in the LAN. ¾ IP Address - The assigned IP address of the controlled computer in the LAN. ¾ Bind - Check this option to enable ARP binding for a specific device. ¾ Mo...

300M Wireless N Router RNX-N300RT User Manual To find an existing entry, follow the steps below. 1. Click the Find button as shown in Figure 4-63. 2. Enter the MAC Address or IP Address. 3. Click the Find button in the page as shown in Figure 4-65. Figure 4-65 Find IP & MAC Binding Entry Click t...

300M Wireless N Router RNX-N300RT User Manual z Load - Load the item to the IP & MAC Binding list. z Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable. Click the Load All button to load all items to the IP & MAC Binding list. Click the ...

300M Wireless N Router RNX-N300RT User Manual Figure 4-71 Time settings ¾ Time Zone - Select your local time zone from this pull down list. ¾ Date - Enter your local date in MM/DD/YY into the right blanks. ¾ Time - Enter your local time in HH/MM/SS into the right blanks. ¾ NTP Server Prior - Enter t...

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to the Router successfully, otherwise, these functions will not take effect. 2) The time will be lost if the Router is tu...

300M Wireless N Router RNX-N300RT User Manual z Traceroute - This diagnostic tool tests the performance of a connection. ) Note: You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name ...

300M Wireless N Router RNX-N300RT User Manual 4.15.3 Firmware Upgrade Choose menu “ System Tools → Firmware Upgrade ”, you can update the latest version of firmware for the Router on the following screen. Figure 4-74 Firmware Upgrade ¾ Firmware Version - This displays the current firmware version. ¾...

300M Wireless N Router RNX-N300RT User Manual 3) Do not turn off the Router or press the Reset button while the firmware is being upgraded, otherwise, the Router may be damaged. 4) The Router will reboot after the upgrading has been finished. 4.15.4 Factory Defaults Choose menu “ System Tools → Fact...

300M Wireless N Router RNX-N300RT User Manual ¾ To upgrade the Router's configuration, follow these instructions. • Click the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. • Click the Restore button. ) Note: The current configur...

300M Wireless N Router RNX-N300RT User Manual 4.15.7 Password Choose menu “ System Tools → Password ”, you can change the factory default user name and password of the Router in the next screen as shown in Figure 4-78. Figure 4-78 Password It is strongly recommended that you should change the factor...

300M Wireless N Router RNX-N300RT User Manual Figure 4-79 System Log ¾ Auto Mail Feature - Indicates whether auto mail feature is enabled or not. ¾ Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as...

300M Wireless N Router RNX-N300RT User Manual Figure 4-80 Mail Account Settings z From - Your mail box address. The Router would connect it to send logs. z To - Recipient’s address. The destination mailbox where the logs would be received. z SMTP Server - Your smtp server. It corresponds with the ma...

300M Wireless N Router RNX-N300RT User Manual Figure 4-81 Statistics ¾ Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be disabled. If disabled, the function of DoS...

300M Wireless N Router RNX-N300RT User Manual Appendix A: FAQ 1. How do I configure the Router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone ...

300M Wireless N Router RNX-N300RT User Manual Figure A-10 Add or Modify a Virtual server Entry 5. The wireless stations cannot connect to the Router. 1) Make sure the " Enable Wireless Router Radio " is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) ...

300M Wireless N Router RNX-N300RT User Manual Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1...

300M Wireless N Router RNX-N300RT User Manual Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: ¾ Setting IP address automatically Select Obtain an IP address autom...

300M Wireless N Router RNX-N300RT User Manual Figure B-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted. ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the following items available 2 If the Router's LAN IP address is 192.168.1....

300M Wireless N Router RNX-N300RT User Manual Figure B-4 Now: Click OK to keep your settings. -123-

300M Wireless N Router RNX-N300RT User Manual Appendix C: Specifications General Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11b, IEEE 802.11g and IEEE 802.11n Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP Ports One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M Auto-Negotiation LAN RJ45 port...

300M Wireless N Router RNX-N300RT User Manual Appendix D: Glossary ¾ 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and incre...