Roper M6707-1-1 - Manuals - manualsarea.com

Page 2 - SUPER PRO GUN & SUPER PRO GUN II

SUPER PRO GUN & SUPER PRO GUN II © 2001 Magnum Venus Products Manual Part No: M6707-1-1 Corporate HQ & Mfg. Phone: (727) 573-2955Fax: (727) 571-3636Email: [email protected]: www.magind.com SUPER PRO GUN & SUPER PRO GUN II Maintenance & Repair Manufacturing Phone: (253) 854-2660 (800...

Page 3 - Table of Contents

SUPER PRO GUN & SUPER PRO GUN II Table of Contents C H A P T E R 1 - ASSEMBLY INSTRUCTIONS Assembly Instructions for Super Pro Gun II Actuator Assembly Instructions for Super Pro Gun II Handle C H A P T E R 2 - ASSEMBLY INSTRUCTIONS C H A P T E R 3 - ASSEMBLY INSTRUCTIONS C H A P T E R 4 - ASSEM...

Page 4 - SUPER; PRO GUN; Repair Kit

SUPER PRO GUN & SUPER PRO GUN II NOTE To order the correct repair kit, refer to the gun handle before ordering parts. SUPER PRO GUN Repair Kit NOTE A Turbulent Mixer is not usedin FIT™ configurations.

Page 5 - II Repair Kit

SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUN II Repair Kit NOTE The Super Pro Gun II is identified by either the blue handle or (on earlierversions) by the #2 stamped on the handle side.

Page 6 - Chapter

SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUNActuator Assembly 5106-01-01 1. Install the 7301-3-020 (O-Ring) onto the 5106-7-1 (ActuatorPiston) and the two 5106-4-1 (Cylinder Caps) 2. Using 6706-3-1 (Pro Gun Oil), lightly coat the Inside of the5106-1-01 (Cylinder Body) and the 5106-7-1 (Actuato...

Page 13 - Gun Block Assembly

SUPER PRO GUN & SUPER PRO GUN II 8 1. Check for and remove debris and burrs in 5104-1-1 (Gun Block). 2. Install the two 5104-3-1 (Secondary Seals) in the 5104-1-1 (GunBlock). See Fig. 3.1 3. Install the 5104-10-1 (Center Spacer) into the center area of the5104-1-1 (Gun Block). 4. Insert the 9301...

Page 20 - Rotor Assembly

SUPER PRO GUN & SUPER PRO GUN II Rotor Assembly 1. Insert 9210-1-1 (Chopper Blades) between the 5103-28-1 (RotorHub) and 5103-29-1 (Wedge Insert). The back edge of the Blademust be bottomed against the Rotor Hub. See Fig. 4.2. 2. Align the edges of the blade with the end of the 5103-28-1 (RotorH...

Page 21 - Rubber Roll Assembly

SUPER PRO GUN & SUPER PRO GUN II Fig. 4.4 Fig. 4.3 Rubber Roll Assembly 5. Press the 5103-6-1 (Rubber Roll) onto the 5103-5-01 (MandrelAssembly). Secure the Rubber Roll by inserting the 7205-3-31(E-Ring) into the groove in the Mandrel. See Fig. 4.4. 6. Insert the Mandrel/Rubber Roll Assembly int...

Page 22 - Rubber Roll Adjustment

SUPER PRO GUN & SUPER PRO GUN II 7. Slide Rubber Roll Assembly toward the 5103-03-01 (Wedge RotorAssembly) and tighten the 7102-2-20 (Socket Head Cap Screw) Rubber Roll Adjustment 1. Slightly loosen the 7102-2-20 (Socket Head Cap Screw), justenough so the Rubber Roll Assembly will slide in the T...

Page 23 - Idler Adjustment

SUPER PRO GUN & SUPER PRO GUN II NOTE Proper adjustment has Idler Assembly touching the Rubber Roll, but still ableto rotate with minimum effort. Fig. 4.7 Idler Adjustment 1. Slightly loosen the 7102-2-20 (Socket Head Cap Screw), justenough so the Idler Assembly will slide in the T-Slot. See Fig...

Page 30 - Rotor Disassembly

SUPER PRO GUN & SUPER PRO GUN II Rotor Disassembly 4. Loosen the two 7102-14-6 (Socket Cup Point Set Screws), andslide the 5103-03-01 (8-Blade Rotor Assembly) off of the 8402-1-1(Air Motor) shaft. 5. Loosen the 7102-13-6 (Socket Flat Head Screws) used to securethe 5103-29-1 (Wedge Inserts), and ...

Page 31 - Assembly Drawings

SUPER PRO GUN & SUPER PRO GUN II SUPER PRO GUN &SUPER PRO GUN II Assembly Drawings Chapter 9 26

Page 34 - SUPER PRO GUN

SUPER PRO GUN & SUPER PRO GUN II Fig. 9.3 29 SUPER PRO GUN

Roper M6707-1-1 - Manuals

Manuals:

Manual Roper M6707-1-1

Summary

Roper Manuals