Roland V-Tour TD-6KW - Manuals

Page 2 - • Exposed to rain or are

2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002b • Do not open or perform any internal modifications on the unit. (The only exc...

Page 3 - Placement; IMPORTANT NOTES

3 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extr...

Page 4 - Drum Stand; Narrow

4 ❑ TD-6V (Percussion Sound Module) x 1 ❑ KD-8 (Kick Trigger Pad) x 1 ❑ FD-8 (Hi-Hat Control Pedal) x 1 ❑ PDX-8 (V-Pad) x 1 ❑ PD-8 (Pad) x 3 ❑ CY-5 (Cymbal Pad) x 1 ❑ CY-8 (Cymbal Pad) x 2 ❑ Connection Cables ❑ Tuning Key x 1 ■ TD-6KW Owner’s Manual x 1 • The tuning key is included in the FD-8 packa...

Page 5 - Use the tuning key to tighten the tuning bolts.; Fine-tune the adjustment while continuing to; Adjusting the Head Tension

5 USING THE UNIT SAFELY fig.PD-85.e_80 add * Do NOT place your fingers inside the shell, as you may hurt yourself or cause damage to the PDX-8. Or when changing the head, do NOT touch any of the internal parts. Also, do not insert your fingers into the hole of the mounting bracket. fig.Stand.j fig.S...

Page 6 - Head Shots; Cross Stick; If you hear a rim sound when you strike the head,; Attaching the Pad to a Stand

6 USING THE UNIT SAFELY Attach the PDX-8 to a pad mount of the stand. Be sure to tighten the stand fixing screw securel. If it remain loose, double triggering may occur. fig.Stand.e Head Shots fig.HeadShot.e * Do not strike the hoop. Rim Shots fig.RimShot.e * To play rim shots, strike the rim in the...

Page 7 - When the Head Should Be Replaced; Place the new head on the shell.; Head Replacement

7 USING THE UNIT SAFELY When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted. Replacement heads (optional): ...

Page 8 - strike both the head and the; Tighten; Specifications; Head Shot

8 USING THE UNIT SAFELY fig.PD-8.e Attach the PDX-8 to a pad mount of the stand. fig.PD-Set.e When attaching the PD-8s to the mounts, be sure to tighten the stand fixing screws securely. If any of them remain loose, the pad could fall off. fig.PD-HR.e To play the sound assigned to the head, hit only...

Page 9 - Making the Settings

9 USING THE UNIT SAFELY fig.CY-8.e When mounting the CY-5 on an L-Rod (pad mount), use ONLY the attachment set as shown below. 1. Mounting the lower clutch and the clutch felt (L). Align the notched section as shown below. Then place the clutch felt (L) so it fits securely. 2. Mount the CY-5 so it f...

Page 10 - Bow Shot; Choking; Attaching the Cymbal Pad to a Stand

10 USING THE UNIT SAFELY fig.CY-8.e 1. Use a tuning key to tighten the stopper bolt. The stopper keeps the cymbal pad from turning, and prevents the cables from catching or getting tangled on the stand. fig.CY-Set01.e 2. Attach the CY-8 so the Roland logo is positioned on the opposite side of the pl...

Page 11 - Adjusting the Travel of the Pedal

11 USING THE UNIT SAFELY fig.FD-8.e • The tips of the anchor bolts are sharp. Handle with care. • When using on flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. • When the FD-8 is not going to be used for a long period of time, move and fix the arm, allowing longer tr...

Page 12 - Adjusting the Foot Plate Height

12 USING THE UNIT SAFELY fig.KD-8.e 1. Remove the screws attached to the reverse side of the KD-8’s trigger. fig.KD-Assy01 2. Pull out the stand in the direction indicated by the arrow until it is fully extended. fig.KD-Assy02 3. Use a tuning key to tighten the screws removed in Step 1 so that the s...

Page 14 - Assemble the “TD-6KW”; KIK; SNR

14 USING THE UNIT SAFELY . 921 Using the provided cables, connect the pads. Connect the L-shaped plugs of the included cables to the pads. To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connectio...

Page 15 - Adding a Cymbal; Trigger Settings for the TD-6V; Examples

15 USING THE UNIT SAFELY . For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-6V must be adjusted. For more detailed informations, refer to the TD-6KV Owner’s Manual. When adding the new pad, use trigger input 10 (CRASH2). With the optional cable (PCS-31L) or a st...

Page 16 - Information

04234201 2PR As of December 10, 2005 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Rolanddistributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street,ARD E1 Golf, Heliopolis, Cairo 11341, EGYPTTEL...