Rockford Fosgate 360.6 - Manuals

T E C H N I C A L D E S I G N F E AT U R E S – 2 – ◆ TRANS•ANA (TRANSconductance Active Nodal Amplifier) The TRANS•ANA (TRANSconductance Active Nodal Amplifier) is a circuit that allows the audio signal to pass through the amplifier at low voltage. The signal is directly level-shifted to the fixed h...

◆ DSM (Discrete Surface Mount) Technology The DSM (Discrete Surface Mount) manufacturing process combines the advantages of both discrete components and integrated circuitry.Rockford Fosgate is the only American amplifier manufacturer to haveinvested millions into this process. DSM components differ...

◆ MOSFET Devices Rockford Fosgate is one of the few manufacturers in the soundcommunity to utilize MOSFET devices in both the power supply and the output stages. MOSFET (Metal Oxide Semiconductor Field Effect Transistor) devices offer several important inherent advantages overthe 30 year old technol...

360. 6 D E S I G N F E AT U R E S 1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch amplifier dissipates heat generated by the amplifier's circuitry. Theinherent advantage of casting provides a 30% improvement of coolingover conventional extrusion heatsink designs. 2. End Caps – Th...

8. Input Sensitivity Controls – The input level controls are preset to match the output of most source units. They can be adjustedto match output levels from a variety of source units. 9. Bass EQ Control – The Bass EQ allows a narrow band adjustmentof up to +18dB centered at 45Hz. The bass boost can...

M O U N T I N G L O C AT I O N The mounting location and position of your amplifier will have agreat effect on its ability to dissipate the heat generated during normaloperation. The design of our cast aluminum heatsink serves to easilydissipate the heat generated over a wide range of operating cond...

B AT T E R Y A N D C H A R G I N G – 9 – Amplifiers will put an increased load on the vehicle's battery andcharging system. We recommend checking your alternator andbattery condition to ensure that the electrical system has enoughcapacity to handle the increased load of your stereo system. Stockelec...

8. Connect the source signal to the amplifier by plugging the RCA cables into the input jacks at the amplifier. 9. Connect the speakers. Strip the speaker wires 5/8". Insert the bared wire into the speaker terminal and tighten the set screw to secureinto place. Be sure to maintain proper speaker...

– 12 – 3386 fo = R (in k Ω ) for .047 µ f cap = R (in k Ω ) for .022 µ f cap 7234 fo Where: R = Ω fo = desired crossover frequency c = capacitor in faradsex: .047 x 10-6 for .047mf cap Crossover Card High PassLow PassFull Range R1 R2 R1 R2 FULL The crossover point can be altered by changing all 4 re...

R E S I S T O R C H A R T Frequency R1 R2 20Hz 169k Ω 169k Ω 25Hz 133k Ω 133k Ω 30Hz 110k Ω 110k Ω 35Hz 95.3k Ω 95.3k Ω 40Hz 84.5k Ω 84.5k Ω 45Hz 75k Ω 75k Ω 50Hz 68.1k Ω 68.1k Ω 55Hz 61.9k Ω 61.9k Ω 60Hz 56.2k Ω 56.2k Ω 65Hz 52.3k Ω 52.3k Ω 70Hz 48.7k Ω 48.7k Ω 75Hz 45.3k Ω 45.3k Ω 80Hz 42.2k Ω 42....

– 14 – XC ARD C ONFIGURATIONS Configure a 12dB/octave filter for Channel A • XCard A set to High-Pass or Low-Pass Configure a 12dB/octave filter for Channel B • XCard B1 set to High-Pass or Low-Pass• XCard B2 set to Full Range Ch. A Ch. A Ch. B R E M D u a l G N D D u a l B + – R + – L + Ch. B HP XC...

U SING THE P HASE S WITCH Vehicle interiors can cause acoustical irregularities with the system'sbass response. The Punch amplifier has a 0 ° /–180 ° phase switch that allows both Channel C outputs to be inverted simultaneously. Sincewoofers will typically be connected to Channel C, the system's bas...

U SING THE S IGNAL S WITCHING N ETWORK The Signal Switching Network allows the RCA input signals to bedistributed to the outputs in many different configurations. Theorientation of both switches configure the distribution pattern. The switches can be oriented in the following configurations: Configu...

– 25 – 360. 6 I N S TA L L AT I O N *Keep grounds asshort as possible Power Connections (Option #1) I NSTALLAT I ON ® ® Ch. A Ch. A Ch. B Ch. B + L – + R – – R + – L + R E M D u a l B + D u a l G N D + – *Keep grounds asshort as possible Power Connections (Option #2) Connect to remoteturn-on lead of...

– 27 – I NSTALLAT I ON ® ® 3-Channel Mono Operation • Gain Control for channels A, B & C operate independently • Impedance Load for bridged channel A should be 4 Ω minimum • Impedance Load for bridged channel B should be 4 Ω minimum • Impedance Load for bridged channel C should be 4 Ω minimum • ...

– 28 – I NSTALLAT I ON ® ® • Gain Control for channels A & B set equally • Gain Control for channel C operates independently • Impedance Load for bridged left channel should be 4 Ω minimum • Impedance Load for bridged right channel should be 4 Ω minimum • Impedance Load for stereo channel C shou...

• Gain Control for channels A, B & C operate independently • Impedance Load for stereo channels A, B & C should be 2 Ω minimum • XCard A can be set for High-Pass, Low-Pass or Full Range• XCard B can be set for 12dB/24dB High-Pass, 12dB/24dB Low-Pass 12dB Bandpass or Full Range • XCard C can ...

Front & Rear w/Midbass and Bridged Subwoofer – 34 – + – + – + – + – XCard C XCard B XCard B XCard A –180 ° 0 ° 80Hz LP 4.5kHz LP 400Hz HP 4.5kHz HP 360. 6 360. 6 + – + – + – + – + – XCard C XCard B XCard B XCard A –180 ° 0 ° 80Hz LP 4.5 kHz LP 400Hz HP 4.5kHz HP Front 12dB/octave High-Pass 4.5kH...

– 35 – T R O U B L E S H O O T I N G Amplifier does notturn on(Power LED is off) Symptom Diagnosis Remedy Voltage applied to theREM terminal of theamplifier is not between10.5 and 15.5 volts ort h e r e i s n o v o l t a g epresent. Voltage to the B+ termi-nal of the amplifier isnot between 10.5 and...

– 37 – Noise is radiating intoRCA signal cable. Bad component in the sig-nal chain. Noise is radiating intospeaker cables. Multiple grounds in theaudio system. Ground loop betweensource unit and antenna. Engine Noise Symptom Diagnosis Remedy Check connections, run theRCA cables on a differentroute a...

– 38 – D Y N A M I C P O W E R M E A S U R E M E N T S About the Dynamic Power MeasurementsThe Audio Graph PowerCube is a test instrument used to measure theoutput of an amplifier in accordance with IHF-202 industry standards. TheIHF-202 standard is a dynamic power measurement and was developedas a ...

Information CubedThe data acquired in the testing procedure is then graphed in the formof a 3-dimensional cube, hence the name PowerCube. The Phase Angle is expressed on the horizontal axis, the Output Voltage is presented on the vertical axis and the Impedance isdisplayed on the Z axis. Output Powe...

– 40 – Continuous Power Rating (Competition Standard) - Measured at 13.8 Battery Volts RMS continuous power per channel, 30 Watts x 6 all channels driven into a 4 Ω load from 20 to 20,000 Hz with less than0.05% Total Harmonic Distortion (THD) RMS continuous power per channel, 60 Watts x 6 all channe...

L E A D E T E N I D A M E N T E L A S S I G U I E N T E S I N S T R U C C I O N E S D EINSTALACION DEL PRODUCTO. EVITARA POSIBLES DAÑOS A VD., ALVEHICULO O AL PRODUCTO. Montaje en el Malatero Monte el amplificador verticalmente con las lineas del radiador orientadasde arriba hacia abajo. De esta man...

– 44 – E SPAÑOL U TILIZACION DEL C IRCUITO DE C ONMUTACION DE S EÑAL El circuito de conmutación de señal permite distribuir las entradas RCAa las salidas de varias diferentes maneras. La orientación de ambosconmutadores configura la distribución de señal. Los conmutadorespueden ser posicionados en l...

Funcionamiento en tres canales – 46 – • Las ganancias de los canales A y B han de ser fijadas igual para igualar los canales • La ganancia del canal C funciona independientemente • La impedancia del canal izquierdo puenteado no debe ser menor de 4 Ω • La impedancia del canal derecho puenteado no deb...

• L Ganancia de los canales A, B y C funcionan independientemente • La Impedancia para los canales A, B y C estereo no debe ser menor de 2 Ω • La XCard A se puede posicionar en HP, LP o Full Range• La XCard B se puede fijar en 12dB/24dB HP, 12dB/24dB LP o 12dB Bandpass o Full Range • La XCard C se p...

ATTENTION: Veuillez lire les instructions suivantes pour l'installation de cetamplifcateur. Ne pas les suivre pourrait causer des blessures ou endommagerle véhicule. Le Punch 360. 6 , est un amplificateur à 6 canaux de 360 watts avec des caractéristiques reprises aux amplificateurs 2 canaux. Quatre ...

Configuration à 3 canaux • Les controles de gain des canaux A et B sont réglés de manière égale pour équilibrer le subwoofer • Les controles de gain des canaux C sont indépendants • L'impédance pour le canal bridgé de gauche doit être de 4 Ω minimum • L'impédance pour le canal bridgé de droit doit ê...

• Les controles de gain des canaux A, B et C sont indépendants • L'impédance pour le canal bridgé de gauche doit être de 4 Ω mini- mum • L'impédance pour le canal bridgé de droit doit être de 4 Ω minimum • La carte de filtrage A peut être réglée en passe-haut, passe-bas ou full range • Les cartes de...

BITTE LESEN SIE DIESE GEBRAUCHSANLEITUNG ZUERST SORGFÄLTIGDURCH. DAS KANN SIE VOR DEM FALSCHEN EINSATZ, AUSFALLENODER SOGAR BESCHÄDIGUNG DES PRODUKTES ODER IHRESFAHRZEUGES SCHÜTZEN. Im Fahrzeugkofferraum Der vertikale Einbau der Endstufen, das bedeutet, da β die Kühlrippen von oben nach unten verlau...

– 54 – B ENUTZEN DES S IGNAL N ETZWERKES Das Schaltbare Signal Netzwerk erlaubt es, die Eingangssignale denverschiedenen Ausgangen optimal zuzuteilen. Die verschiedenenStellungen der Schalter sind in den folgenden Beispielen dargestellt. Beispiel #1 Kanal A Eingang => Kanal A AusgangKanal B Einga...

Ch. A Ch. A Ch. B Ch. B R E M D u a l B + D u a l G N D Rear – + 2 ohm min. + – LED Ch. C Bass EQ Ch. C Gain Ch. C Ch. B Ch. A Ch. B Gain Ch. A Gain L R L R L R Ch. C Ch. C + L – 2 ohm min. – L + – + – – R + Front 2 ohm min. – 2 ohm min. + – + 2 ohm min. + R – + L – + – 2 ohm min. + R – 6-Kanal Ster...

I TALIANO ATTENZIONE: SI PREGA DI LEGGERE LE SEGUENTI ISTRUZIONI PERL'INSTALLAZIONE DI QUESTO PRODOTTO. IL NON SEGUIRLE POTREBBERISULTARE SERIAMENTE DANNOSO PER LA PERSONA O PER IL VEICOLO. Il Punch 360.6 é un amplificatore da 360 watt totali e 6 canali progettatoper essere installato come un singol...

Ch. A Ch. A Ch. B Ch. B R E M D u a l B + D u a l G N D – L + – R + + R – – + 4 ohm min. + – LED Ch. C Bass EQ Ch. C Gain Ch. C Ch. B Ch. A Ch. B Gain Ch. A Gain L R L R L R Ch. C Ch. C + R – + L – 4 ohm min. + L – + – 4 ohm min. Funzionamento a 3 canali • I gain dei canali A e B regolati identici p...

Ch. A Ch. A Ch. B Ch. B R E M D u a l B + D u a l G N D Rear – + 2 ohm min. + – LED Ch. C Bass EQ Ch. C Gain Ch. C Ch. B Ch. A Ch. B Gain Ch. A Gain L R L R L R Ch. C Ch. C + L – 2 ohm min. – L + – + – – R + Front 2 ohm min. – 2 ohm min. + – + 2 ohm min. + R – + L – + – 2 ohm min. + R – Funzionament...

9/96MAN-1364-A MADE IN THE USA This product is designed, developed and assembled in the USA by a dedicated group of American workers. The majority of the components used in the construction of this product are produced by American companies. However, due to the global nature of their manufacturing f...