Riccar RCU-H11 - Manuals

5 Installation Unit Installation Using the mounting plate provided with your vacuum cleaner, secure the unit to the wall (figure 1) , at a height allowing easy access for maintenance of the dirt receptacle and/or bags (see page 4). The connections to the piping system will require some basic tools: ...

6 Installation Using the Right Air Intake (except H3 model) To use the air intake located on the right side of the vacuum: 1. Using a flat screwdriver, loosen the clamp collars and remove the rubber coupling from the left air intake (figure 4) . . 2. Unlatch the two clips and remove the dust recepta...

7 Installation Utility Valve installation (H7, H9 & H11 models) 1. Secure the T-elbow on the air intake (see page 5, figure 3 ). 2. Install the utility valve on the T-elbow. 3. Connect the low voltage wiring (see pages 10 & 13).

8 Installation Dos & Don’ts Installing Conduits

A B A B B B A A 10 Installation Dos & Don’ts Installing Inlets When installing your vacuum inlets, we recommend that the principle of electric polarity be taken into account. Ensure that the wire connected onto contact A on inlet 1 is the same as that connected to contact A on inlet 2, and so on...

11 Installation (Optional) 1. Insert the rubber coupling on the vacuum air exhausts.2. Using a Phillips screwdriver, tighten the clamp collar to ensure adequate sealing. 3. Insert the 90° elbow into the rubber coupling and tighten, then clamp collar as per instructions in step 2. 4. Apply ABS glue t...

12 Installation Grounding Instructions This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and g...

13 Installation Low Voltage Connections Connect the low voltage wires to the low voltage inlet on your unit. To do so: 1. Strip wires over 1 cm (1/2 inch) (figure 10) . 2. Gently press on the toggle to open the connector (figure 11) . 3. Insert stripped wire (figure 12) . 4. Release toggle to secure...

14 Operating Instructions Hose Hook-Up & Inlets Before operating your central vacuum… Please verify that it is properly connected to the piping system, and to a grounded electrical outlet, and that the low voltage wires are connected to the unit (see pages 5 to 13). Then read the complete owner’...

15 Operating Instructions Progressive Start (H9 & H11) Each model is equipped with a special module allowing for a smooth and gradual start-up of the vacuum system to prolong motor durability. Automatic Stop (H9 & H11) In case you’ve forgotten to turn off your vacuum, or it’s been turned on ...

16 Maintenance Motor Please note that Riccar motors do not require lubrication. Each motor contains two carbon brushes which will wear normally, and may eventu -ally require replacement. For warranty purposes, this should be done by an authorized service center. Brush life is affected by the number ...

17 Maintenance Maintenance For use with bag Change the bag when the one in place is full. Frequency will depend on the use of the unit. For the H9 & H11 models, the information center will indicate when to change the bag. These indications are provided by an electronic timing board, only as a re...

18 Maintenance Maintenance For use without bag We recommend you empty the dust receptacle and clean the permanent filter at least each season, depending on use of your central vacuum. 1. To empty the dust receptacle: Disconnect the unit from the electric outlet. Unlatch the two clips, remove the rec...

19 Maintenance Converting the Unit Your Riccar central vacuum unit was designed for use with or without disposable bag. Though it is sold with a bag installed, it can easily be removed, and the unit modified for use without disposable bags. 1. Using a flat screwdriver, loosen the clamp collars and r...

20 Maintenance Carbon Dust Filter (H9 & H11 models) replacements. The integrated monitor will indicate provided by an electronic timing board, only as a reference guide. To do so: 1. Unlatch the opening on the carbon filter case and gently flip it upward (figure 21) . 2. Remove the used filter, ...

21 Troubleshooting General Information If the vacuum unit does not work, check the fuse or breaker on the unit and/or in the electrical panel in your home, and replace any defective part(s) as deemed necessary. Please verify that the unit has been installed properly, according to the instructions in...

25 Troubleshooting Troubleshooting Problem Possible cause Corrective action Vacuum will not stop Hose improperly inserted into vacuum inlet Ensure that the hose end is properly inserted into the vacuum inlet. The tab on the hose end should line up withthe slot in the inlet opening.(See page 14). Def...

26 Warranty Information Limited Lifetime Warranty WHAT IS COVERED / HOW LONG COVERAGE LASTS: All permanently installed components of a Riccar central system are warranted to be free of defects in material and workmanship under normal use to the original purchaser at the original installation address...

27 Warranty Information HOW TO GET SERVICE: Warranty service can only be obtained by contacting an Authorized Riccar Retailer. A proof-of-purchase and product serial number will be required before service is rendered. To locate your nearest Riccar Retailer, please call 1-888-6-Riccar or visit the Ri...