Page 3 - Introduction; carefully and keep it handy for future reference.; INSTALLATION; lighting is recommended for comfortable viewing.
2 Introduction Thank you very much for purchasing your LED TV. It serves as a normal colour TV and a PC monitor. To enjoy your set fully from the very beginning, read this manual carefully and keep it handy for future reference. INSTALLATION ① Locate the receiver in the room where direct light does ...
Page 4 - Warning; Class I structures of equipment should be connected to the grid
3 Warning This symbol is intended to alert the user to avoid the risk of electric shock. This equipment may only be disassembled by qualified service personnel. This symbol is intended to alert the user to the presence of important operation and maintenance instructions in the literature accompanyin...
Page 5 - Caution; To prevent fire or electrical shock hazard, do not expose; do not place objects filled; Caution
4 Caution Caution High voltages are used in the operation of this product. - Do not open the product's casing. Refer servicing to qualified service personnel . Caution To prevent fire or electrical shock hazard, do not expose the main unit to rain or moisture , do not place objects filled with liqui...
Page 7 - power lines or circuits.; Important Information
6 Television Antenna Connection Protection External Television Antenna Grounding If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges. Article 810 o...
Page 8 - Attaching or Removing the Stand; the bottom of the stand. Screw in the 4 screws to secure the stand.
7 Attaching or Removing the Stand 1. To attach the base place the display unit flat on a table. Afterwards attach the stand onto the bottom of the stand. Screw in the 4 screws to secure the stand.
Page 9 - Installing Batteries to the Remote Control; Only use AAA batteries.
8 2. To remove the stand, remove the 4 screws in the area and the stand will come off. Installing Batteries to the Remote Control Please insert two AAA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the batteries with the (+) and (-) symbols inside the battery...
Page 10 - Identifying Front and Rear Panel; Front View; INDICATOR LIGHT
9 Identifying Front and Rear Panel Front View Rear View Mounting Pattern INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LED in the panel, the TV might take 10 – 12 seconds to power on. REMOTE SENS...
Page 11 - If You Have Digital Cable without Cable Box or Antenna...; Make sure the power of HDTV is turned off.; Connection Suggestions
10 If You Have Digital Cable without Cable Box or Antenna… 1. Make sure the power of HDTV is turned off. 2. Connect the Coaxial RF cable from your antenna or digital cable to the TV port on the back of your HDTV. 3. Turn on the HDTV. 4. Follow the first time on screen instructions. Please Note: No...
Page 13 - Connecting WiiTM with Composite...; Make sure the power of HDTV and your WiiTM is turned off.; This source shares audio jacks with YPbPr.
12 Connecting Wii™ with Composite… 1. Make sure the power of HDTV and your Wii™ is turned off. 2. Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™ and AV’s Yellow Video connector port on the back side of your HDTV. 3. Obtain a RCA Audio Cable. Connect the white color...
Page 14 - Connecting Cable or Satellite boxes with HDMI...; Make sure the power of HDTV and your set-top box is turned off.; HDTV supports NEC’s universal remote code. Please look up NEC’s
13 Connecting Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned off. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port on the back of your HDTV. 3. Turn on the HDTV and your set-top box. 4. Use the remote...
Page 15 - Connecting to a PC with VGA and 3.5 mm minijack ...
14 Connecting to a PC with VGA and 3.5 mm minijack … 1. Make sure the power of HDTV and your PC is turned off. 2. Obtain a 15-pin D-Sub VGA cable; connect to the VGA output of your PC and the other end to the VGA port on the back of your HDTV. 3. Obtain a 3.5 mm Mini-jack, connect to the audio out o...
Page 16 - Connecting a Digital Audio Receiver with Coax SPDIF...; Make sure the power of HDTV and your receiver is turned off.; The TV’s SPDIF out for 5.1CH is ONLY used for antenna/cable
15 Connecting a Digital Audio Receiver with Coax SPDIF… 1. Make sure the power of HDTV and your receiver is turned off. 2. Obtain a coax SPDIF cable, connect it to your receiver’s coax SPDIF digital input and the coax SPDIF connection on the LINE OUT port on the back of the HDTV. 3. Turn on the HDTV...
Page 18 - Remote control; : When stereo program is received, press this key to; Switch the program digit.; Display TV information.; This button is not available.; INFO; : Display some information of current program in TV mode.
Remote control POWER : Power on/off button, press once to turn the TV on and press again to turn the TV off. MUTE: Press this button to mute or restore sound. MTS/AUDIO : When stereo program is received, press this key to switch sound system between mono and stereo. When SAP program is received, pre...
Page 19 - Installation Guide; MENU; PICTURE; ” button to select “Picture Mode”, press “
18 Installation Guide Press MENU button to display the MAIN OSD MENU ; Press ◄ / ► button to select the MENU you want; Press ENTER button to enter the sub menu; Press ▼ / ▲ button to select the option and then press ◄ / ► to adjust the value in the sub menu; You can press MENU button to go back to t...
Page 20 - Press the “MENU” button to enter the OSD menu .Then press “
19 SOUND You can select the type of sound, which best corresponds to your listening. Press the “MENU” button to enter the OSD menu .Then press “ / ” button to select the “SOUND” menu. 1. Press “ ” button to select “Sound Mode” and Press “ / ” button to select. 2. Press “ / ” button to ...
Page 21 - SETUP; Press “
20 2. Press “ / ” button to select “Time Zone” and press the “ / ” button to enter time zone adjustment menu to select the local time zone. 3. Press “ / ” button to select “Daylight Saving Time” and press the “ / ” button to select “On” or “Off”. Note: The ' Daylight Saving Time ' it...
Page 23 - LOCK; Note: The default password is “0000”; Note; : If you forget your password, you can use
22 LOCK Press the “MENU” button to enter the OSD menu .Then press “ / ” button to select the “Lock” menu. 1. Press “ ” button to select “Enter Password” and press select digital button to enter. Note: The default password is “0000” 2. Press ▼ / ▲ button to select Change Password, then press “ ...
Page 24 - select
23 3. Press “ / ” button to select “System Lock” and press the “ / ” button to select “On” or “Off”. 4. Press “ / ” button to select “US” and press the “ / ” button to then press “ / ” button to select “TV”. A Sub Menu will appear as below. Press “ / ” button to select “MPAA”...
Page 25 - Channel
24 Channel Press the “MENU” button to enter the OSD menu .Then press “ / ” button to select the “Channel” menu. 1. Press “ ” button to select “AIR/CLABLE ” and press the “ / ”button to select Cable or AIR. 2. Press “ / ” button to select “Auto Scan” and press the “ ENTER/ ” button to...
Page 26 - A Sub Menu will appear as below.; “DTV Signal” Display the quality of current DTV signal.; NOTE
25 6. Press “ / ” button to select “Channel Label” and press the “ / ” button to Rename label of the channel. A Sub Menu will appear as below. 7. “DTV Signal” Display the quality of current DTV signal. NOTE : This is not a choice.
Page 27 - types of chemicals might damage the housing and the LCD glass.; Cleaning the bezel and remote control; wipe it, please lightly dampen the wiping material (; the wiping material cannot; with clean water and wipe again. Wipe the; Cleaning the Screen; How do I clean the TV?
6 2 IMPORTANT 1. The power cable has to be removed from the socket before cleaning the TV. 2. Do not use volatile solvent (alcohol, rosin, and toluene) to clean the TV. These types of chemicals might damage the housing and the LCD glass. Cleaning the bezel and remote control 1. Use a 100% cotton clo...
Page 28 - Troubleshooting; Problems; For adjust controls; TV’S
Troubleshooting The following table contains the common problems and the solutions to these problems. Please check this list before you contact the technicians. Problems Solutions NO PICTURE Connect power cord correctly. Turn on power. Connect video cable correctly. Select the input signal source wi...
Page 29 - up some channels but forgot about them.
28 Problems Solutions TV CHANNELS ARE BLOCKED Check your auto lock function’s settings inside the OSD. You may have locked up some channels but forgot about them. UNIVERSAL REMOTE CODE This TV follows NEC’s universal remote code. Please check your hand book for NEC’s codes then apply them. THE TV TU...
Page 32 - Specifications; TV DISPLAY
31 Display panel Item Illustration Active Area / Screen Size Diagonal 32 inches Aspect Ratio Widescreen 16:9 Pixel Pitch 0.17 (H) x RGB x 0.51 (V) um per one triad Max. of Pixels (Resolution) HD (1366 x 768 pixels) resolution Specifications Brightness 250 nits (Typical) Contrast 1200:1 (Typical) wit...
Page 34 - signal cord and power cord supplied with this unit.; FCC Compliance Statement
33 This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: This device may not cause harmful interference This device must accept any interference received, including interference that my cause undesired operation. Please Note: This equipment has been te...
Page 35 - LED TV; MANUEL D’UTILISATION
Page 40 - Ne montez jamais sur le téléviseur, ne vous appuyez pas dessus et; Précaution; Ne placez pas le téléviseur sur un chariot, une étagère, ou une table; Précaution
1.4 Précautions Précaution Ne montez jamais sur le téléviseur, ne vous appuyez pas dessus et ne le poussez pas brusquement de son socle. Prêtez particulièrement attention aux enfants. Précaution Ne placez pas le téléviseur sur un chariot, une étagère, ou une table instable. Le téléviseur risque de t...
Page 41 - Protection de la connexion de l’antenne de télévision; Mise à la terre de l'antenne externe de télévision; système de télévision par câble.; Lignes électriques; Collier de mise à la terre; Informations Importantes
Protection de la connexion de l’antenne de télévision Mise à la terre de l'antenne externe de télévision En cas de connexion de l'appareil à une antenne extérieure ou un système de télévision par câble, assurez-vous que ces derniers sont mis à la terre afin de les protéger des surtensions électrique...
Page 43 - Vue avant; LAMPE TÉMOIN; - Le télé-capteur reçoit toutes les commandes de la télécommande.; Vue arrière du schéma de montage; en utilisant une vis; Installation des piles dans la télécommande
Identification des panneaux avant et arrière Fixation ou enlèvement du support Informations Importantes Identification des panneaux avant et arrière • • Vue avant LAMPE TÉMOIN - La lumière est rouge lorsque l'appareil est branché, mais le téléviseur n'est pas allumé. La lumière s'allume en bleu lors...
Page 45 - ou; Suggestions; Identification des panneaux avant et arrière; de connexion
Pour la câblodistribution numérique sans boîte de jonction ou antenne ... 1. Assurez-vous que l’alimentation du téléviseur HD est coupée. 2. Branchez le câble coaxial RF à partir de votre antenne ou câble numérique au port TV à l’arrière de votre téléviseur HD. 3. Allumez le téléviseur HD. 4. La pre...
Page 46 - Connecter le lecteur DVD avec YpbPr composant...; Allumez le téléviseur HD et votre lecteur DVD.; Cette source partage les prises audio avec la vidéo composite.
Connecter le lecteur DVD avec YpbPr composant… 1. Assurez-vous que l’alimentation du téléviseur HD et de votre lecteur DVD est coupée. 2. Procurez-vous un câble composant. Branchez le connecteur de couleur verte à la fois à votre lecteur DVD et au port du connecteur vert de l’YPbPr à l’arrière de vo...
Page 47 - Connexion WiiTM avec composite...; Allumez le téléviseur HD et votre console WiiTM.
Connexion Wii™ avec composite… 1. Assurez-vous que l’alimentation du téléviseur HD et votre Wii™ est éteinte. 2. Procurez-vous un câble vidéo jaune. Branchez le connecteur vidéo jaune à la fois à votre Wii™ et au port du connecteur vidéo jaune de l’AV à l’arrière de votre téléviseur HD. 3. Procurez ...
Page 48 - Cette source partage les prises audio avec l’YPbPr.; Allumez le téléviseur HD et votre boîtier décodeur.; HDTV prend en charge le code de la télécommande universelle NEC.
Cette source partage les prises audio avec l’YPbPr. Connexion du récepteur câble/satellite avec HDMI ... 1. Assurez-vous que l’alimentation du téléviseur HD et de votre boîtier décodeur est coupée. 2. Branchez un câble HDMI à la sortie HDMI de votre boîtier décodeur et l'autre extrémité au port HDMI...
Page 50 - Connecter un récepteur audio numérique avec un coaxial SPDIF ...; Allumez le téléviseur HD et votre récepteur.; de SPDIF sous format PCM.
Connecter un récepteur audio numérique avec un coaxial SPDIF ... 1. Assurez-vous que l’alimentation du téléviseur HD et de votre récepteur est coupée. 2. Procurez-vous un câble coaxial SPDIF, connectez-le à l'entrée numérique SPDIF coaxiale de votre récepteur et la liaison coaxiale SPDIF au le port ...
Page 51 - Vue générale; CH- : Permet d’accéder à la chaîne précédente
2.2 Vue générale 2.3.1. Panneau avant 1211 1. VOL- :Pour baisser le volume 2. VOL+ : Pour augmenter le volume 3. CH- : Permet d’accéder à la chaîne précédente 4. CH+ : Permet d’accéder à la chaîne suivante 5. MENU : Permet d’afficher le Menu principal des réglages 6. TV/AV : Permet de sélectionner l...
Page 52 - Entrez les chiffres du programme.; Affichage des informations télé.; Télécommande
POWER (MARCHE/ARRÊT) : Appuyez le bouton de mise en marche/arrêt une fois pour allumer le téléviseur et appuyez de nouveau pour l'éteindre. MUTE (SOURDINE) : Appuyez sur ce bouton pour mettre en sourdine ou réactiver le son. MTS/AUDIO (MTS/AUDIO) : Lorsque le programme stéréo est reçu, appuyez sur c...
Page 53 - Guide d'installation; L’élément « Tint » (« Teinte ») est utilisé en mode NTSC uniquement.; Réglage de base de OSD; Appuyez sur le bouton «
Guide d'installation Appuyez sur le bouton MENU pour afficher le menu OSD principal ( MAIN OSD MENU ) ; Appuyez sur le bouton ◄ / ► pour sélectionner le MENU désiré ; Appuyez sur le bouton ENTER (ENTRÉE) pour accéder au sous-menu; Appuyez sur le bouton ▼ / ▲ pour sélectionner l'option puis appuyez s...
Page 54 - L’élément «; SPDIF Type; » (« Type SPDIF ») est utilisé uniquement dans le; Audio Language; » (« Langue audio ») est utilisé uniquement dans le
SOUND (AUDIO) Vous pouvez sélectionner le type de son qui correspond le mieux à votre écoute. Appuyez sur le bouton « MENU » pour accéder au menu OSD. Puis appuyez sur le bouton « / » pour accéder au menu « SOUND » (« AUDIO »). 1. Appuyez sur le bouton « / » pour sélectionner « Sound Mode » ...
Page 55 - le bouton «; Daylight; » (« Heure avancée ») est utilisé uniquement
Appuyez sur le bouton « MENU » pour accéder au menu OSD . Puis appuyez sur le bouton « / » pour accéder au menu « TIME » (« MINUTERIE »). 1. Appuyez sur le bouton « / » pour sélectionner « Sleep Timer » (« Minuterie de veille »), puis appuyez sur le bouton « / » pour accéder au menu de r...
Page 56 - bouton «
bouton « / » pour accéder au menu «Setup» (« Configuration »). 1. Appuyez sur le bouton « / » pour sélectionner « OSD Language » (« Langue d’affichage à l’écran »), puis appuyez sur le bouton « / » pour accéder au menu de réglage de la langue d’affichage à l’écran pour sélectionner la la...
Page 58 - Remarque : Le mot de passe par défaut est « 0000 »
8. .Appuyez sur le bouton « / » pour sélectionner « Reset Default » (« Rétablir les paramètres par défaut »), puis appuyez sur le dialogue « ». Appuyez sur le bouton « / » en sélectionnant « Yes » (« Oui ») pour restaurer tous les réglages au paramètres par défaut. LOCK (VERROUILLAGE) Appu...
Page 59 - Remarque; : Si vous oubliez votre mot de passe, vous pouvez utiliser
Remarque : Si vous oubliez votre mot de passe, vous pouvez utiliser « 8899 » pour accéder à n'importe quel menu verrouillé. 3. Appuyez sur le bouton « / » pour sélectionner « System Lock » (« Verrouillage du système »), puis appuyez sur le bouton « / » pour sélectionner « On » (« Activer ») ...
Page 60 - Appuyez sur le bouton «
4. Appuyez sur le bouton « / » pour sélectionner « US », puis appuyez sur le bouton « / » et sur le bouton « / » pour sélectionner « TV ». Le sous-menu A apparaîtra comme suit. Appuyez sur le bouton « / » pour sélectionner « MPAA », puis appuyez sur le bouton « / »pour régler. 5....
Page 61 - Le sous-menu A apparaîtra comme; sur le bouton «
1. Appuyez sur le bouton « / » pour sélectionner « AIR/CLABLE » (« AIR/CÂBLE »), puis appuyez sur le bouton « / » pour sélectionner Cable (Câble) ou AIR (Air) 2. Appuyez sur le bouton « / » pour sélectionner « Auto Scan » (« Recherche automatique »), puis appuyez sur le bouton « / » ...
Page 62 - « DTV Signal » (« Signal DTV ») Affichage de la qualité du signal DTV actuel.; REMARQUE; A apparaîtra comme suit.
7. « DTV Signal » (« Signal DTV ») Affichage de la qualité du signal DTV actuel. REMARQUE : Ce n'est pas une option 6. Appuyez sur le bouton « / » pour sélectionner « Channel Label » (« Étiquette de chaine »), puis appuyez sur le bouton « / » pour renommer l’étiquette de la chaîne. Le sous-m...
Page 63 - le chiffon; Utilisez un chiffon en microfibres ou 100 % coton pour le nettoyage.
Nettoyage du téléviseur IMPORTANT 1. Débranchez l'appareil de la prise murale avant de procéder au nettoyage. 2. Do not use volatile solvent (alcohol, rosin, and toluene) to clean the TV. These types of chemicals might damage the housing and the LCD glass. Nettoyage du cadran et de la télécommande 1...
Page 64 - Dépannage
Le tableau suivant contient les problèmes communs et les solutions à ces problèmes. Veuillez consulter cette liste avant de contacter les techniciens. Problèmes Solutions PAS D'IMAGE Branchez le cordon d'alimentation correctement. Mettez sous tension. Branchez le câble vidéo correctement. Sélectionn...
Page 67 - Spécifications
Panneau d'affichage Point Illustration Taille de la zone active / de l'écran Diagonale de 32 pouces Format Écran large 16:9 Distance entre pixels 0,17 (H) x RVB x 0,51 (V) um par une triade Max. de pixels (résolution) Résolution HD (1366 x 768 pixels) Luminosité 250 nits (typique) Contraste 1200 : 1...
Page 68 - watts par chaîne
Mode audio Musique / Standard / Cinéma / Utilisateur Contrôle automatique du volume Oui Tonne Bass / Aigus / Balance Sortie SPDIF Oui (coaxial) Haut-parleurs 6 watts par chaîne (3) Général Tuner TV hybride NTSC / ATSC / QAM (Câble Numérique Prêt) Balayage automatique des chaînes Oui Minuteur de mise...
Page 69 - Déclaration de conformité FCC
Ce dispositif est conforme à la partie 15 de la réglementation FCC. Le fonctionnement est soumis aux conditions suivantes : Cet appareil ne doit pas générer d'interférences nuisibles Cet appareil accepte toute interférence reçue, y compris les interférences qui peuvent perturber son fonctionnemen. V...