QSC S series - Manuals - manualsarea.com

Page 2 - CAUTION; AVIS; VORSICHT

2 © Copyright 2002 QSC Audio Products, Inc. All rights reserved. “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office. RAVE™ is a trademark of QSC Audio Products, Inc. CobraNet™ is a trademark of Peak Audio, Inc. E X P L A N A T I O N O F G R A P H I C A LS Y M B O L S The...

Page 3 - RAVE “S” Series Digital Audio Router User Manual; page numbering synchronized with the printed document.; Table of Contents

3 RAVE “S” Series Digital Audio Router User Manual Warning Notices ................................................................................................................................................. 2 Introduction ...........................................................................

Page 4 - Overview

4 RAVE™ Digital Audio Router products provide a means of transporting CobraNet™ audio signals over a Fast Ethernet network. Using standard network hardware and physical me- dia, a RAVE system has a maximum capacity of 64 audio chan- nels on a 100BASE-TX repeater segment and the ability to support hu...

Page 5 - Illustration of RAVE units

5 Power LED Bundle assignmentselector switches(behind cover) Network status LEDs Audio signal level LEDs Front view of a RAVE 161s-24; other models are similar Rear view, from top: RAVE 160s-24, RAVE 188s-24, RAVE 161s-24, RAVE 80s, RAVE 88s and RAVE 81s INTRODUCTION: Illustration of RAVE units IEC ...

Page 6 - Glossary

6 AES3— A digital audio format specification approved by the Audio Engineering Society and European Broad- cast Union for inter-device conveyance of a dual- channel (stereo) digital audio signal. Also called AES/EBU. This specification is periodically revised and amendments are published by the AES....

Page 8 - How It Works

8 Ethernet networks are used most often for data communica- tions, such as with file or print sharing on an office LAN (Lo- cal Area Network). A typical application might include a num- ber of PCs or workstations, servers and shared printers all connected to common Ethernet hardware. Messages (Ether...

Page 10 - Channel Routing

10 Channel Routing A RAVE network handles routing in bundles of up to eight audio channels. Each bundle of audio transmitted on the network oc- cupies a unique identifier, or number. In stand-alone mode, each RAVE device handles two bundles—two sent, two received, or one of each. For example, a RAVE...

Page 11 - remove the top cover of the RAVE unit as follows.

11 PRE-INSTALLATION PREPARATION: ANALOG AUDIO SIGNAL LEVELS (RAVE 160/161/188 ONLY) CAUTION: Detach the power cordbefore removing the top cover.Dangerous voltages within theenclosure may be of sufficientmagnitude to constitute a risk ofelectric shock to humans. To remove cover, first detach the AC p...

Page 14 - ANALOG AUDIO CONNECTIONS; tion at right shows how the detachable headers work.; To connect a wire to a terminal:; Use a wire tie to secure the cable to the grip of the header block.; To connect balanced inputs:; insert the signal conductor into the + terminal and the shield to; 6 analog audio input channels labeled 1 through 16

14 ANALOG AUDIO CONNECTIONS The analog RAVE models (RAVE 160 /161 and 188) use normal analog balanced audio inputs and outputs, with three terminals per channel: Hi (+), Lo (-) and Shield.. Analog audio inputs and outputs connect using detachable terminal strip headers on the rear panel of the RAVE ...

Page 15 - The actual channel assignment depends on the model.; DIGITAL AUDIO CONNECTIONS; To construct an AES3 digital audio cable:; use 110 ohm digital audio

15 Channel numbers and connector pinouts are labeled on the rear of the unit, as shown in the illustration above. The actual channel assignment depends on the model. DIGITAL AUDIO CONNECTIONS The digital RAVE models (RAVE 80/81/88) use the AES3 (also known as AES/EBU) digital audio standard. Each AE...

Page 16 - How to use for Redundant Operation:

16 2A 250V 20 x 5 mm FUSE (2 required) • The detachable AC power cord connects to the RAVE at the rear-panel IEC connector. • There is no power switch; the AC disconnect device is the detachable power cord. • A RAVE operates on line voltages from 100 to 240 VAC, 50 to 60 Hz. No user setting is requi...

Page 17 - REDUNDANT CONFIGURATION; Rear panel coax cable and Ethernet connections; Sync Connection for Redundant Operation, RS-232 Port

17 REDUNDANT CONFIGURATION (hardware setup) To slave one RAVE unit to another, connect a male-to-male BNC jumper cable from the sync output of the master unit to the slave input of the redundant unit. Select the same bundle assignment(s) on the slave unit as are selected on the mas- ter unit. Bundle...

Page 18 - receiver at channel input number 1 is required.; Synchronizing the CobraNet Network to an AES/EBU Stream; SYNCHRONIZING TO AES/EBU

18 The RAVE “s” series AES/EBU input models provide some additional means for synchronizing the CobraNet network and deriving on-board clocks. In addition to the on-board PLL and external synch inputs available on all models, the AES/EBU input models allow the user to synchronize the network to a 48...

Page 19 - and be configured for

19 Connections: Synchronizing the CobraNet Network to an AES/EBU Stream Method 2: Use the recovered AES 48 kHz clock as an “external clock” source. When the jumper at header J37 is set to “AES”, the CobraNet interface uses the recovered 48 kHz clock at the first XLR connector (inputs 1 and 2) as the...

Page 20 - STATUS INDICATORS

20 The eight status indicator LEDs display the operating condition of the RAVE unit and its connection to the Ethernet network. They are color coded such that green LEDs, when illuminated, signify a good or normal condition, while red LEDs signify a problem. The “Conductor” LED is yellow and simply ...

Page 21 - highest; Fault; remedy for a faulty RAVE unit.

21 Tx This LED illuminates green for at least 50 milliseconds while the unit is transmitting Ethernet data. This indicator will blink when transmit activity is present. The activity of this indicator is dependent on the RAVE model and bundle type. This is a physical layer indicator and does not guar...

Page 22 - Audio Signal Level Indicators; AUDIO SIGNAL LEVEL INDICATORS; Yellow—when the signal peaks exceed -12dBFS; CobraNet VERSION

22 When powering up a RAVE with CobraNet version 2, the major and minor release of the firmware is displayed on the two 8-channel groups in binary format. The left group displays the major release and the right group displays the minor release. For example, if the CobraNet version in the RAVE is 2.8...

Page 23 - ERROR REPORTING; . Unicast traffic is analogous to a; BUNDLE ACTIVITY

23 ERROR REPORTING Operation: Audio Signal Level Indicators One of the most useful features of the metering LEDs on RAVE products is that they indicate CobraNet connectivity infor- mation by providing “bundle activity” status. An active or valid bundle assignment is indicated by illuminating the ass...

Page 24 - switches to the same hex value as the transmitter.; PROGRAM AND “SOFTWARE KILL”; simplest implementation.; ROUTING

24 A RAVE network routes audio signals in bundles of up to 8 channels. Behind the removable cover on the front panel are two pair of hexadecimal switches for assigning bundles to the 8-channel audio groups. Note that the following discussion only applies to front panel configuration of RAVE devices ...

Page 25 - All bundles are multicast on network repeaters.

25 Switches set to “10” through “FE” hex assign unicast bundles. Switches set to “01” through “0F” hex assign multicast bundles. Switch settings “00” and “FF” hex are reserved for special functions. “FF” hex puts the unit into utility mode for programming and also forces software kill. “00” hex disa...

Page 26 - Network Design Considerations:; General Info and Switched Networks; SWITCHED NETWORKS

26 There are a number of ways to design a CobraNet LAN. Sev- eral resources such as device specifications, Architect & Engineer’s specifications, topology references, lists of ap- proved network hardware and design guidelines are avail- able on the Peak Audio website (www.peakaudio.com). Addi- t...

Page 28 - REPEATER NETWORKS; Repeater Networks

28 REPEATER NETWORKS • RAVE supports operation on network repeaters. These repeaters should be 100 Mbps class II devices. Collisions are prevented through CobraNet’s propri- etary “order persistent” media access scheme. RAVE invokes this access scheme by auto-sensing its link partner (network hardwa...

Page 29 - Specifications; GENERAL; Maximum AC Line Current Draw:; ANALOG INPUTS; Common Mode Rejection:; AES3 INPUTS

29 Specifications GENERAL AC Line Voltage: 100V to 240V, auto-configuring AC Line frequency: 50 Hz to 60 Hz, auto-configuring Maximum AC Line Current Draw: 600 mA @ 100V Thermal Operating Range: 0° C to 65° C ANALOG INPUTS Connector Type: 3-pin Phoenix (euro-style), detachable terminal block Audio R...

Page 30 - AES3 OUTPUTS

30 Specifications ANALOG OUTPUTS (continued) Output Impedance: <200 ohms (electronically balanced) Frequency Response: 20 Hz to 20 kHz, ±0.5 dB Dynamic Range, typical: 102 dB FS @ 997 Hz Dynamic Range, worst-case: >100 dB FS @ 997 Hz Idle Channel Noise (A-weighted): 104 dB FS (20 Hz to 20 kHz)...

Page 32 - ETHERNET CABLING; are wired identically.; Appendix; RS-232 PORT INFORMATION; Pin assignments of 9-pin female D connector:

32 ETHERNET CABLING This diagram shows the pinout for standard unshielded twisted-pair (UTP) network cable. Both ends of the cable are wired identically. RJ-45 pinout for a standardEthernet patch cable (bothends identical) 1 Tx + 2 Tx – 3 Rx + 4 not used 5 not used 7 not used 8 not used 6 Rx – 1 Tx ...

Page 33 - Resources; CobraNet Discovery; Network Hardware Manufacturers

33 Appendix: Resources QSC RAVE resources: http://www.qscaudio.com - Visit our website regularly for up-to-date RAVE information such as: Technology papers Configuration procedures Management aids Internet links to other networked audio information sources Client list (venues utilizing RAVE) Article...

Page 34 - How to Contact QSC Audio Products; Main Number; Product Warranty

34 How to Contact QSC Audio Products Address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telephone Numbers: Main Number (714) 754-6175 Sales Direct Line (714) 957-7100 Sales & Marketing (800) 854-4079 (toll-free in USA only) Technical Services (714) 957-7150 ...