QSC PB2082-I - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY PRECAUTIONS; Disclaimer

2 IMPORTANT SAFETY PRECAUTIONS Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer. WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets...

Page 3 - Introduction

3 Introduction The Installation Line Array (ILA) is a high performance line array system designed for the needs of Houses of Worship, Performing Arts facilities and a multitude of other venue types. The current ILA family is composed of the WL2082-i line array element, WL115-sw sub-woofer, FB2082-i ...

Page 4 - Rigging

4 Introduction (continued) WL115-sw The WL115-sw subwoofer extends the system’s low-frequency capability to 35 Hz. with a compact fourth-order bandpass enclosure. Its ceramic magnet, 4” voice coil, 15” transducer provides 650 watt continuous power handling capability. Many users of line array system...

Page 6 - Rigging the Installation Line Array; Rules for Suspension; Shock Loading

6 Rigging the Installation Line Array Rules for Suspension •Correct use of all suspension hardware and components is imperative in sound system rigging and deployment. •Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load ...

Page 7 - Rigging the Installation Line Array (continued); Attaching WL2082-i to Array Frame

7 Rigging the Installation Line Array (continued) 1- Working Load Limits are per fastener loaded in double shear. Data is for informational purposes only. Attaching WL2082-i to Array Frame Before beginning any installation, have your system designer configure the array with proper splay angles using...

Page 8 - Extension Bar

8 Rigging the Installation Line Array (continued) Pull-Back Bar If using the pull-back bar, attach to the bottom enclosure at the bot-tom-most splay angle adjustment holes at the rear of the rigging plate by inserting the cap-head shoulder bolt through the mated pieces and threading the lock nut (ny...

Page 9 - Attaching the GS115-sw Ground Stack Rails to a WL115-sw

9 Rigging the Installation Line Array (continued) 3- Lower the array frame onto the enclosure, carefully aligning the rigging straps, and attach the top enclosure to the array frame by installing the ball-lock pins or M8 bolts. Before lifting, ensure the audio connection to the enclosures are correc...

Page 11 - WL2082-i Controls and Connections; MODE Selection Switch

11 WL2082-i Controls and Connections MODE Selection Switch BI AMP: When set to BI AMP, an internal shading net- work removes the mid-frequencies from one of the low-frequency drivers. The BI AMP HORIZONTAL SHADING switch will select which transducer is shaded. TRI AMP: Shading network is NOT applied...

Page 12 - Input Connections; Neutrik NL8FC Cable Connector Pinout

12 WL115-sw Connections Input Connections The WL115-sw input connectors are a pair of Neutrik NL8's wired in parallel. See Table 3 or the WL115-sw Input Plate for connector pinout. Note pin numbers 2+, 2-, 3+, 3-, 4+, and 4- are wired straight through from one connector to the other. This accommodat...

Page 14 - WL115-sw Specifications

14 WL115-sw Specifications Frequency Response: 37 - 107 Hz (+/- 3 dB) Frequency Range: 35 - 112 Hz (-10 dB) Maximum SPL (continuous/peak): 124 dB/130 dB Transducer: 650W, 8 Ohm 15 inch woofer, 4 inch voice coil, ceramic magnet assembly Recommended Crossover Frequency: 35 - 85 Hz Input Sensitivity: 9...

Page 16 - GS115-sw Specifications

16 PB2082-i Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Working Load Limit Information: GS115-sw Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Weight 5 lb (2.3 kg) per set Component Weight 5:1 Design Factor 7:1 Design Factor...

Page 20 - How to Contact QSC Audio Products

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2006 “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA...