QSC DSP 322UA - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS

2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous” voltage within the product’s enclosure that may be of sufficient magnitude to constitute a ris...

Page 3 - Introduction

3 Introduction 1- Power indicator2- Diagnostic indicator3- Network status indicators4- Sinal presence indicators5- Multi-function push buttons6- Display7- Rotary select/accept knob8- Safe Mode switch (recessed)9- Analog outputs 10- mic/line inputs11- Relay outputs 12- Logic outputs13- Omni inputs14-...

Page 5 - Introduction - Networking the DSP 322ua; Notes on Network System Design:

5 Introduction - Networking the DSP 322ua Notes on Network System Design: As with any communications system, the reliability and performance of a local area network (LAN) is intimately related to the designer's skill and knowledge in implementing a topology that is robust, efficient and standards-co...

Page 8 - Unpacking; Mounting; Rack Mounting

8 Unpacking There are no special unpacking precautions. However, it is recommended you keep the original packing material for reuse in the rare event that service be required. If service is required and the original packing material is not available, ensure that the unit is adequately protected for ...

Page 9 - Computer Requirements & Software Installation; General Information & Configuration Memories; Network

9 Computer Requirements & Software Installation Installing QSControl.net is easy. All you need to do is choose the folder where the program is to be stored (the default setting is accept-able for most applications). We recommend your system meet the following minimum requirements: 1- IBM PC comp...

Page 10 - Connections

10 Connections AC Power Cord Insert the molded receptacle of the AC power cord into the AC power inlet on the back of the DSP 322ua. Plug the AC line connec-tor into the AC outlet. The power supply will accept from 100 to 240 Volts AC, 47 to 440 Hertz, without any changes. If a different type of IEC...

Page 11 - Relay Out; LED Indicators

11 Relay Out Two sets of relay contacts are provided, RELAY OUT 1 and RELAY OUT 2. Contacts are floating and rated for 30VDC, 1A. There is one common terminal, one normally-closed contact terminal and one normally-open contact terminal. These are labeled as C, NC and NO on the rear panel. When the r...

Page 12 - LCD Display and Controls; Front Panel Password Lockout

12 LED Indicators (continued) QSControl Status (Port) Indicators- There are three LEDs on the front and rear panels labeled RX, TX and LINK. These indicate the status for the QSControl.net network. Their functions are described below. RX (receive) - This indicator illuminates any time the DSP 322ua ...

Page 13 - LCD Navigation Map

13 LCD Navigation Map Left side buttons have screen dependent functions. This read-only screen is the “out of the box” default display after power up. This is the most desired information when first setting up a network system. Once user moves to a different screen, the last screen accessed becomes ...

Page 14 - Getting Started

14 Getting Started This section outlines one of the simpler methods of getting familiar with your DSP 322ua and the QSControl.net software. The goal of this procedure is to get your computer and the DSP 322ua connected and communicating and the QSControl.net software installed and running. After the...

Page 16 - Operation; QSControl Port; Utility/Diagnostic Functions; Safe Mode Switch

16 Operation QSControl Port The QSControl port operates on a 10BaseT Ethernet network. This port is one of the primary means for connecting QSControl.net to the DSP 322ua. The port may connect directly to a PC's 10BaseT or 10/100 (auto-sensing or auto-negotiating) network interface card using a cros...

Page 17 - Telnet Access

17 Utility/Diagnostic Functions (continued) RS-232 Communications Procedure: 1) Connect the RS-232 port of the DSP 322ua to an unused serial port (COM port) of a PC using a normal (straight-through) serial cable. 2) Open the HyperTerminal program. This program is usually started by clicking the Wind...

Page 18 - Preliminary Specification

18 Preliminary Specification IN OUT THRU Dynamic Range (AES-17, -60dB Method, all sensitivities) unweighted >110dB >112dB >108dB A weighted >113dB >115dB >111dB Distortion (20Hz-20 KHz, all sensitivities) Gain= 0 - 30dB <0.008% THD+N <0.009% THD+N <0.009% THD+N Gain >30...

Page 20 - How to Contact QSC Audio Products

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2005 “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA...