QSC 722AZ - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS

2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous” voltage within the product’s enclosure that may be of sufficient magnitude to constitute a ris...

Page 3 - Introduction

3 1- Power indicator2- Diagnostic indicator3- Network status indicators4- Port connection status indicators5- Multi-function push buttons6- Display7- Rotary select/accept knob8- Reset push switch (recessed)9- DataPorts 10- Analog inputs11- Monitor chain in/out 12- Relay outputs13- Logic outputs14- O...

Page 4 - Notes on Network Systems Design:

4 Block Diagram Introduction - Networking the BASIS 722az The BASIS 722az includes an RJ-45 network connection port on the rear panel, which is labeled "QSControl". All data communications between the BASIS 722az and a control computer, such as a PC running the QSControl.net server or client...

Page 7 - Unpacking; Item; Mounting; Rack Mounting

7 Unpacking There are no special unpacking precautions. However, it is recommended you keep the original packing material for reuse in the rare event that service be required. If service is required and the original packing material is not available, ensure that the unit is adequately protected for ...

Page 8 - Computer Requirements & Software Installation; Start; General Information & Configuration Memories; Amplifier Setup

8 Computer Requirements & Software Installation Installing QSControl.net is easy. All you need to do is choose the folder where the program is to be stored (the default setting is acceptable for most applications). We recommend your system meet the following minimum requirements: 1- IBM PC compa...

Page 9 - Connections

9 Connections AC Power Cord Insert the molded receptacle of the AC power cord into the AC power inlet on the back of the BASIS 722az. Plug the AC line connector into the AC outlet. The power supply will accept from 100 to 240 Volts AC, 47 to 440 Hertz, without any changes. If a different type of IEC...

Page 10 - Monitor Chain; Ports; LED Indicators

10 Monitor Chain connection. See explanation, at left. In Out Monitor Chain The MONITOR CHAIN connector is a 5-pin terminal block connector. Input and output con- nections are balanced. The center pin is the shield connection for both the input and output of the monitor chain. Connection is shown at...

Page 11 - LCD Display and Controls; Front Panel Password Lockout

11 LED Indicators (continued) QSControl and CobraNet Network Status (Port) Indicators- There is a group of three LEDs on the front and rear panels of the BASIS 722az labeled RX, TX and LINK. These indicate the connection status of the BASIS 722az to the QSControl net- work. Their functions are descr...

Page 13 - Getting Started

13 Getting Started This section outlines one of the simpler methods of getting familiar with your BASIS and the QSControl.net software. The goal of this procedure is to get your computer and the BASIS connected and communicating and the QSControl.net software installed and running. After the softwar...

Page 14 - Device; Design Editor; Help

14 Getting Started (continued) 17- Select Device , Add New Device , from the menu. A new window will open prompting you to name the device. Name it logically, such as BASIS 1, or similar. Select the Device Type and select BASIS 722az. At the Password prompt, enter “qsc” (lower case, no quo-tation ma...

Page 15 - Operation; QSControl Port; Utility/Diagnostic Functions; Safe Mode Switch; Location of Safe Mode switch:

15 Operation QSControl Port The QSControl port operates on a 10BaseT Ethernet network. This port is one of the primary means for connecting QSControl.net to the BASIS. The port may connect directly to a PC's 10BaseT or 10/100 (auto-sensing or auto-negotiating) network interface card using a crossove...

Page 17 - Telnet Access; OK

17 Utility/Diagnostic Functions (continued) Telnet Access The RS-232 features can also be accessed via Telnet. The Microsoft Telnet application is a Windows program. Consult Windows documentation for Telnet information. Basic procedure for opening a Telnet session: 1 - To open the Telnet session- Cl...

Page 18 - Preliminary Specification

18 Preliminary Specification IN OUT THRU Dynamic Range (AES-17, -60dB Method, all sensitivities) unweighted >115dB >112dB >110dB A weighted >118dB >115dB >113dB Distortion (20Hz-20 KHz, all sensitivities) +4dBu (max) <0.009% THD+N <0.009% THD+N <0.009% THD+N 2dB below clip...

Page 20 - How to Contact QSC Audio Products; QSC Audio Products 3 Year Limited Warranty

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2004 “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA...