ProCom QN300RYLA-W - Manuals

5 AIR FOR COMBUSTION AND VENTILATION WARNING: This heater shall not be installed in a confinedspace or unusually tight con-struction unless provisions areprovided for adequate combus-tion and ventilation air. Read thefollowing instructions to insureproper fresh air for this and otherfuel-burning app...

6 WARNING: Rework worksheet, adding the space of the adjoining unconfinedspace. The combined spaces must haveenough fresh air to supply all appliances inboth spaces. If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is anunconfined space. You will need no add...

7 WATER VAPOR:A BY-PRODUCT OFUNVENTED ROOM HEATERS Water vapor is by-product of gascombustion.an unvented roomheater prodrces approximately one(1) ounce (30ml) of water for every 1,000BTU’s (.3kw’s) of gas input perhour.Unvented room heaters are recom-mended as supplemtal heat (aroom) rather that a ...

8 CLEARANCES TO COMBUSTIBLES(Vent-Free Operation Only) Carefully follow the instructions below.This stove is a freestanding unitdesigned to set directly on the floor. IMPORTANT : You must maintain minimum wall and ceiling clearancesduring installation. The minimumclearances are shown in Figure 4.Mea...

1 1 OPERATING HEATER FOR YOUR SAFETY READ BEFORE LIGHTING A. This appliance has a pilot which must be lighted by control system,When lighting the pilot, followt h e s e i n s t r u c t i o n s e x a c t l y . B . B E F O R E L I G H T I N G s m e l l a l l around the appliance area forgas. Be sure t...

1 2 b. manual select of main burner: Press BURNER button, the flame ison “MAN” select. At this selection, themain burner will keep working no matterwhat the temperature is set at. If there isa need to shut off the main burner, justpress the “BURNER” button to make the burner on the “OFF” select. c.s...

1 3 INSPECTING BURNERS C h e c k p i l o t f l a m e p a t t e r n a n dburner flame patterns often. PILOT FLAME PATTERN Figure 18 shows a correct pilot flame pattern. Figure 19 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple.This will cause the the...

1 4 Air Passageways Use a vacuum cleaner or pressurized air to clean. Exterior Use a soft cloth dampened with a mild soap and water mixture. Wipethe cabinet to remove dust. LOGS If you remove logs for cleaning, refer to Installing Logs to properlyreplace logs. Replace logs if broken or chipped (dime...

1 5 SPECIFICATIONS QL300RYLA QN300RYLA QL300RYLA-W QN300RYLA-W Btu(Variable)Gas Type LP Gas Natural GasIgnition Automatic AutomaticManifold Pressure 8"W.C. 3"W.C.Inlet Gas Pressure(In. of water)* Maximum 14" 10.5" Minimum 11" 5"Dimensions, Inches (H×W×D) Heater 25 4/5"×32...

1 6 TROUBLESHOOTING REMEDY WARNING :Make sure that power is turn off before proceeding.... WARNING: Turn off and let cool before servicing. Only a qualifiedservice person should service and repair fireplace. CAUTION: Never use a wire,needle, or similar object to cleanODS/pilot. This can damage ODS/p...

1 7 TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Delayed ignition burner 1. Manifold pressure is too low2. Burner orifice clogged 1. Contact local gas company2. Clean burner (see Cleaning and Maintenance, page 13) Burner backfiring during combustion 1. Damaged burner2. Gas regula...

1 9 PARTS LIST QL300RYLAQN300RYLAQL300RYLA-WQN300RYLA-W

2 2 PLACING INSTRUCTION Follow the procedures below and the instruction drawings to put log sets inplace to the gas stove(indoor vent-free). NOTICE: THE CORRECT POSITION OF THE LOGS SHOULD NOT IM- PINGE ON THE FLAME. THE LOG’S PACKAGE ISLOCATED INSIDE THE UNIT THEN REMOVE SCREEN AND TAKEOUT THE LOG’...

2 4 FIG(3) FIG(4) STEP 2: Install the log 2 on the right rear angle iron. see FIG(3) STEP 3: Install the log 3 on the front angle iron. See FIG(4). 1 INSTALLATION INSTRUCTIONS FOR LOG SETS 1. All logs FIG(1) FIG(2) STEP 1: Install the log 1 on the left rear angle iron. see FIG(2)