Primera Max - Manuals

Optical Disc Laminator Connectivity Guide 1 Optical Disc Laminator Connection Guide THANK YOU… Thank you for purchasing the Optical Disc Laminator Connectivity Kit. This kit will allow you to use your Optical Disc Laminator in conjunction with the Pro, XL and MAX versions of Optical Disc Duplicators...

2 Optical Disc Laminator Connectivity Guide e. Make certain the Laminator has been plugged into power and turned on. f. Select "Install Software Automatically" and click Next . 510887.qxd 1/21/2004 7:35 PM Page 2 TOC

Optical Disc Laminator Connectivity Guide 3 g. You may see a notice like the one shown here stating that the Accent Disc Laminator has not passed Windows Logo Testing. Click the Install Anyway button to continue installing the printer driver for your Laminator. Once the driver has finished installin...

4 Optical Disc Laminator Connectivity Guide The following steps describe in detail how to connect the Laminator to your DuplicatorMAX: a. Connect the Laminator Stand to the left hand side of the DuplicatorMAX as shown: b. Remove the Input Bin closest to the Laminator Stand to make room for the Lamin...

Optical Disc Laminator Connectivity Guide 5 5) From the Main Application Screen click Robotics then Options . 6) Enable the Use Laminator checkbox. 7) Click the button labeled Move to (Calibrate) . This will move the Picker Mechanism to the Laminator Tray position. 8) Lower the disc to the Laminator...

6 Optical Disc Laminator Connectivity Guide b) While the LEDs are flashing, press the Pause button. The Picking Mechanism will lower to the Laminator Tray Position. c) Adjust the Laminator Tray forward and back by loosening the adjusting screws located towards the front of the stand. d). For left-to...

Optical Disc Laminator Connectivity Guide 7 f) Tighten the Adjusting Screws on the front of the Laminator Stand to lock the stand in position. 9. You have now calibrated your Laminator to the Duplicator MAX and are ready to produce discs! D. CREATING DISCS WITH YOUR DUPLICATOR MAX IN PRIMO Laminatin...

8 Optical Disc Laminator Connectivity Guide The Laminator is positioned at the front left corner of the Duplicator. The optional Duplicator XL/Pro Laminator Stand is needed for both of these configurations. The stand is shown here: STAND-ALONE MODE The Automated Stand-Alone Mode allows you to connec...

Optical Disc Laminator Connectivity Guide 9 4. Connect the Laminator Stand to the back of the Laminator as shown: 5. Place the Laminator on the Laminator Stand as shown: There are two sets of holes on the underside of your Laminator. Set the Laminator on the stand locating the smaller set of holes o...

10 Optical Disc Laminator Connectivity Guide 6. Connect the Auxiliary Control Cable and Power Cable the Laminator as shown: 7. Align the Laminator's tray position to the picker. This is done as follows: a. Make certain the Laminator has power and is turned on. b. Load a disc into the Input Bin. This...

Optical Disc Laminator Connectivity Guide 11 8. The Laminator is now aligned properly. Once the Laminator's Heat Roller has achieved proper operating temperature (indicated by a solidly lit Ready LED on the Laminator's Control Panel), you are ready to laminate discs. Load the input bin with discs an...

12 Optical Disc Laminator Connectivity Guide 4. Place the Laminator on the stand. The Laminator will need to be placed on the stand with the Laminator's rubber feet resting in the four holes located on the top of the Stand as shown: 5. Using the provided USB Cable, connect the Laminator to your PC a...

Optical Disc Laminator Connectivity Guide 13 c. If the Laminator Tray is not in the OUT position, press the Laminate button to eject the Laminator Disc Tray. d. From the Main Application Screen click Robotics then Options. e. Enable the Use Laminator checkbox. f. Click the button labeled Move to (Ca...

14 Optical Disc Laminator Connectivity Guide 8. From the Main Application Screen click Robotics then Options . Select Lamination as shown: 9. Set up your print and record job as you normally would per the Duplicator XL/Pro User's Manual. 10. Click the red circle Record button to start your job! 5108...

Optical Disc Laminator Connectivity Guide 15 F. TROUBLESHOOTING Problem Resolution Will not Laminate • Check Power to the Laminator • Make sure that the Ready LED is on and steady indicating the Laminator's Heat Roller has achieved normal operating Temperature I do not see an option • In PrimoDVD, c...

Printed in the United States of America P/N 510887 510887.qxd 1/21/2004 7:35 PM Page 16