Premier Mounts PWM-F110 - Manuals

PWM-F110 Page - 6 - Installation Manual Parts List NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installati...

PWM-F110 Installation Manual Page - 7 - Mounting Bracket Installation NOTE : Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING :...

PWM-F110 Page - 8 - Installation Manual 3. If needed, install the nylon spacers to the mounting points on the flat panel (Figure 3). 4. Lay the left and right mounting brackets (stamped arrows facing out) - (Figure 4). Figure 3 Figure 4 5. Match the center of viewing guide with the centerline you ma...

PWM-F110 Page - 10 - Installation Manual Wall Stud Location 1. Using a (commercially available) wood stud finder, locate four 16" or 24" stud centers behind the wall. Once found, make a pencil marking on the center of the wood studs (Figure 9). NOTE: The wall plates have (3) 16" and (1) ...

PWM-F110 Page - 11 - Installation Manual 3. To connect the two wall plates, lay them on a flat surface, end to end. Make sure that the holes line up (Figure 11). 4. Insert two (2) M8 x 16mm Hex Head bolts through the two holes and secure with two (2) M8 Hex nuts (Figure 11). 5. Place the bottom port...

PWM-F110 Installation Manual Page - 12 - 7. Level and secure the plate to the wall with the reference arrow facing up to the ceiling. 8. Secure the plate using the eight (8) 5/16" lag bolts and flat washers (supplied) – (Figure 13). CAUTION: Do not over tighten the lag bolts. NOTE : Use a minimu...

PWM-F110 Page - 13 - Installation Manual 9. Level and secure the plate to the wall with the reference arrow facing up to the ceiling. 10. Use a minimum diameter of 5/16” x 2 ¼” large concrete wedge anchors (commercially available) – (Figure 14). CAUTION: Do not over tighten the wedge anchors bolts. ...

PWM-F110 Installation Manual Page - 14 - Installing the Flat Panel Display WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. 1. Raise the flat panel with the LEFT...

PWM-F110 Page - 15 - Installation Manual 2. Make any lateral shift adjustment and lock it by tightening the two (2) ¼”-20 Phillips screws found on the bottom of the mounting brackets. Use the wall bumper to adjust your flat panel. CAUTION : Do not over tighten the ¼”-20 screws to the rods (Figure 16...

PWM-F110 Installation Manual Page 19 Technical Specifications 16.000(406.4) 16.000 (406.4) 1.943(49.3) 5.000 (127) 28.000 (171.2) CL 3.500 (88.9) CL 5.000 (127) 16.000(406.4) 24.290 (616.97) 16.000 (406.4) 21.790 (553.4) 1.245 (31.75) A B C D E F G H B A F H 21.790 (553.4) Figure 17

PWM-F110 Page 20 Installation Manual Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, displa...

PWM-F110 Installation Manual Page - 18 - Notes Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 [email protected] www.mounts.com