Premier Mounts PSD-BW - Manuals

PSD-BW/L Page - 5 - Installation Instructions BW Base Castor Installation (Figure 1) Unpack the PSD-BW/L Nesting Cart and review any WARNING statements that apply to the installation. Select the desired location for the PSD-BW/L Nesting Cart. Figure 1 1. Place the BW/L on a flat surface. NOTE : Make...

PSD-BW/L Installation Instructions Page - 6 - PSD-SPA Installation (Figure 3) NOTE : Use of the PSD-SPA will depend on the mount that is used. All PSM/CTM Series mounts require using the PSD-SPA. The Revolution Series, USA and UFA Mounts, however, do not require the use of the PSD-SPA. 1. Slide the ...

PSD-BW/L Page 7 Installation Instructions Optional Mounting Configurations CTM-Series Revolution Series USA/UFA Series

PSD-BW/L Installation Instructions Page 8 Technical Specifications All measurements are in inches (mm). Notes PSD-BW PSD-BWL

RTM-L TABLE OF CONTENTS Warranty 2 Contact Premier Mounts 2 Warning Statements 3 Parts List 4 Installation Tools 4 Thread Depth Indicator 7 Mount Installation 8 Universal Mounting Bracket Installation 9 Display Orientation 11 Securing the Display 11 Tilt Positioning 12 Optional Configurations 12 Tec...

RTM-L Page 4 Installation Instructions Parts List NOTE : This mount is shipped with all installation hardware and components. Make sure that none of these parts are missing and/ or damaged before beginning installation. If there are parts missingand/or damaged, please stop and contact Premier Mounts...

Page 6 Installation Instructions RTM-L Parts List (Cont.) Nylon spacers and flat washers' actual size NOTE : The nylon spacers may be stacked to achieve proper spacing. 1/2" Nylon spacers (large) Nylon sleeves (Qty 8) (Qty 12) (Qty 8) (Qty 8) (Qty 8) (Qty 8) 1/4" Nylon spacers (Small) (Qty 8...

RTM-L Installation Instructions Page 7 Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panelto make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread...

RTM-L Page 8 Installation Instructions NOTE : The installation instructions that are contained in this manual refer only to the RTM-L. The installation instructions for the various bases that are used with the RTM-L will be included with those products. NOTE : Prior to installing the RTM-L, the moun...

RTM-L Installation Instructions Page 9 Universal Mounting Bracket Assembly 1. Place the universal bracket bar and the universal brackets on a flat surface.2. Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing up. At this time, do not tighten the s...

RTM-L Page 10 Installation Instructions 3. Lower the universal bracket bar and display into the cradle (as to the left). NOTE : The circular portion of the universal bracket bar must rest inside the nylon sleeve. If seated improperly, the operation of the RTM-L will be hindered and the nylon sleeve ...

RTM-L Installation Instructions Page 11 Display Orientation The RTM-L will allow the user to adjust the display a full 360°. WARNING : BEFORE ROTATING THE RTM-L, MAKE SURE THAT THE M6 KNURL KNOB IS SECURELY FASTENED TO THE RTM-L. ALSO, PLEASE MAKE SURE YOU ALLOWENOUGH CABLE AND WIRE CLEARANCE FOR FU...

RTM-L Page 12 Installation Instructions Optional Configurations Technical Specifications All measurements are in inches (mm). PSD-TS PSD-BW PSD-EB

1 2 I N S T A L L A T I O N M A N U A L www. idt .com .au Phone: 1300 666 099 PSD-SHB Black Shelf Step 1 Open the box and remove all components. Step 2 Slide the shelf over the poles, select the desired height and lock the height by tightening the four (4) Allen head screws using the hex key.