Page 2 - Read these instructions carefully before you use the Nailer.
2 Always wear approved front and side EYE PROTECTION when operating this Nailer. Others in the work area should also wear front and side EYE PROTECTION . Eye protection will help guard against flying nails and debris, which could cause severe eye injury. EAR PROTECTION may be required to prevent hea...
Page 3 - FLEX Foot Adjustment:; Raise or lower the FLEX to your wood sample.
ADAPTER FOOT LOCATING EAR 3 FLEX Foot Adjustment: Wood varies from one manufacturer to the next. The different wood profiles may be due to height and length of the flooring tongue and whether or not there is a nail pocket.First, loosen the two hex bolts under the FLEX foot with the Allen Wrench supp...
Page 4 - and could stain the wood flooring, walls or furnishings.; We will not be responsible for oil stains.; and may damage the seals. Consult the filter regulator; WARNING; flooring, walls or furnishings. Dry fire the Nailer, without; We will not be responsible for oil stains.; WARNING
4 WARNING It is not necessary to hit the Nailer hard to activate it. Never hit the Nailer with excessive force or with the metal end of the mallet, this will damage the Nailer.Never use the Safety Trigger interlock to lock up the plunger and rack the wood with blows to the Nailer body. This will sev...
Page 5 - DRIVING BLADE ASSEMBLY REMOVAL:; Videos and
from turning while unscrewing the Jam Nut by holding the piston hex with the 1-1/8" box wrench supplied.6. Push out the 1/4" diameter blade retaining Dowel Pin and remove the broken Driving Blade stub.7. Install a new Driving Blade in the slot and replace the Dowel Pin. Screw on the retainin...
Page 8 - Powernail FLEX with Power Roller - Parts List
ITEM # PART NO. DESCRIPTION Qty Req’d Key Ref. Assy/Kit 1 09-50P-3001 Body 1 F 2 09-50P-3002 Cap 1 S 3 09-445-29815 Handle - Extra Long 1 S/A A-5 4 09-445-29703 Handle - Long 1 S/A A-2 5 09-445-29703.1 Handle - Short 1 S/A A-3 6 09-445-29704 Handle Half Cover 1 S/A A-2,A-3,A-5 8 09-50P-3006 Foot 1 S...
Page 9 - Powernail FLEX Assemblies, Kits and Accessories
ITEM # PART NO. DESCRIPTION QTY REQ’D Key/Ref Assy/Kit 47 09-445-29745 #10-32 X 1-1/4 SHCS (Knob) 1 S/A A-4,A-9 48 09-445-29747 1/4-20 X 1-1/4 SHCS W/patch (Foot) 4 S 49 09-445-29748 5/8-18 Jam Nut (Driving Blade) 1 S/A A-6 50 09-445-29750 #8-32 X 1-1/2 FHCS (Spacer) 2 S/A A-4 51 09-445-29751 #8-32 ...
Page 10 - Seal Placement
Page 11 - SCHEMATIC - FLEX with POWER ROLLER
11 SCHEMATIC - FLEX with POWER ROLLER 76 78 79 72 73 77 83 89 86 92 93 87 63 71 91 75 48 54 82 85 88 84 81 63 8 52 FLEX Power Roller Conversion Parts. For Step-by-Step Videos and Instructions, Visit our Web Site at www.Powernail.com
Page 12 - POWERCLEATS LENGTH DETERMINATION CHART
POWERCLEATS LENGTH DETERMINATION CHART This chart will assist you in determining the proper length of Powercleats to use for various thicknesses of flooring. Approximate vertical penetration of the Powercleat under the hardwood floor is shown for each application. This is only a guide. Results shoul...
Page 13 - POWERNAILER TROUBLE SHOOTING CHART
13 PROBLEM POSSIBLE CAUSE SOLUTION 1 Driving blade does not retract 1. Zero or Low air pressure Check air supply for 70 psi minimum to 110 psi maximum 2. Lack of lubrication Manually lubricate through male air inlet fitting 3. Excessive dirt inside nailer Disassemble and clean 4. Bent or burred driv...
