Poulan PRO 96192001803 - Manuals

Page 2 - IMPORTANT; Safe Operation Practices for Walk-Behind Snow Throwers

2 IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: This snow thrower is for use on sidewalks, driveways and ot...

Page 3 - CUSTOMER RESPONSIBILITIES; Clearing a Clogged Discharge Chute; TABLE OF CONTENTS; PRODUCT SPECIFICATIONS

3 CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance.Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent,...

Page 4 - PARTS PACKED SEPARATELY IN CARTON; REMOVE SNOW THROWER FROM CAR TON

4 PARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maint...

Page 8 - OPERATION; KNOW YOUR SNOW THROWER

8 OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols ma...

Page 10 - HOW TO USE YOUR SNOW THROWER

10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vi...

Page 12 - BEFORE STARTING THE ENGINE

12 TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for cu...

Page 13 - SNOW THROWING TIPS

13 TO START ENGINE • Be sure fuel shut-off valve is in the OPEN position.Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household ...

Page 14 - MAINTENANCE; LUBRICATION CHART

14 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made perio...

Page 15 - ENGINE

15 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate ...

Page 16 - SERVICE AND ADJUSTMENTS; SNOW THROWER

16 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower. 4. Connect spark plug wire to spark plug. Replace safety ignition key. WARNING: To avoid serious injury, before performing any service or ad just ments: 1. Be sure throttle is in STO...

Page 19 - TROUBLESHOOTING

19 Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position. 4. Move throttle to FAST position. 5. Choke...

Page 21 - REPAIR PARTS

21 KEY PART NO. NO. DESCRIPTION 4 191079 Pulley, Impeller 5 188909 Bearing Assembly, Flange 6 155377 Nut, Hex Flange 5/16-18 7 180355 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 72270505 Bolt, Carriage 5/16-18 9 163183 Bolt, Hex Head 10 404930X428 Housing, Auger 11 404933X479 Bar, Scraper 12 178675X00...

Page 32 - LIMITED WARRANTY

LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur- chaser, we will repair or replace, at our option, wit...