Poulan PRO 195806 - Manuals

6 ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper ...

7 ASSEMBLY FIG. 4 2466 02464 SEAT PAN SHOULDER BOLT ADJUSTMENT KNOB FLAT WASHER SEAT FIG. 3 NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. INSTALL SEAT (See Fig. 3) Adjust seat before tightening adjustment knob...

9 ASSEMBLY CHECK TIRE PRESSURE The tires on your tractor were overinfl ated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.• Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” section of this manual. CHECK DECK LEVELNESS For best cutt...

10 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-ing. OPERATION DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FO...

11 OPERATION 02561LSW KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. Compare the illustrations with your tractor to familiarize yourself with the location of various controls and adjustments. Save this man ual for future reference. HEIGHT AD JUST MENT KNOB...

12 OPERATION FIG. 9 MOWER BLADES -• To stop mower blades,move attachment clutch switch to “DIS EN GAGED” po si tion. GROUND DRIVE -• To stop ground drive, depress brake pedal into full “BRAKE” position. IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY...

13 OPERATION DE FLEC TOR SHIELD FIG. 11 TO OPERATE ON HILLS WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills. FIG. 10 02142 PUSH IN TO "D...

14 OPERATION TO START ENGINE (See Fig. 8) When starting the engine for the fi rst time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.• Be sure freewheel control is in the transmission en gaged position. • Sit on seat in operating posi...

15 OPERATION FIG. 13 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run- ning. To ensure proper operation and performance, it is rec om -mend ed that the transmission be purged before operating tractor for the fi rst time. This procedure will remove any tra...

16 MAINTENANCE LUBRICATION CHART ➀ SPRAY SILICONE LUBRICANT (MOVE BOOTS TO LU BRI CATE) ➁ GENERAL PURPOSE GREASE ➂ REFER TO MAINTENANCE“ENGINE” SECTION IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LU BRI CANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORT ...

17 MAINTENANCE BLADE REMOVAL (See Fig. 14) • Raise mower to highest position to allow access to blades. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.• Remove blade bolt by turning counterclockwise.• Install new or resharpened blade with stamped "THIS SIDE UP" facin...

18 MAINTENANCE TRANSAXLE COOLING The fan and cooling fi ns of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos-sible damage to seals, no not use high pressure water or stea...

19 MAINTENANCE 00667 MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam-age. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs fi rst. Spark plug type...

20 TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PROD UCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT (See Fi...

23 SERVICE AND ADJUSTMENTS TO ADJUST ATTACHMENT CLUTCH (See Fig. 25) The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop a...

24 0066 3sq RE TAIN ING RING WASH ERS FIG. 28 AXLE COVER TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL (See Fig. 28)• Block up axle securely.• Remove axle cover, retaining ring and washers to allow wheel removal. • Repair tire and reassemble.• Replace washers and snap retaining ring securely in axle groov...

26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open fl ame or spark. Allow the engine to cool before stor...

27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air fi lter. 5. Clean...

29 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-als and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, w...

31 15 DEGREES MAX. FOLD ALONG DO TTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL,NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mowslopes greate...

This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. For Parts and service, contact our authorized distributor: call 1-800-849-1297 • ...