Poulan PRO 195018 - Manuals

6 ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard wrench sizes are listed.(1) 3/4" wrench Pliers (1) 9/16" wrench Tire pressure gauge Utility knife When right or left hand is mentioned in this man ual, it means when you are in the operating po si...

7 ASSEMBLY NOTE: You may now roll or drive your tractor off the skid. Follow the ap pro pri ate instruction below to remove the tractor from the skid . FIG. 2 FIG. 3 2466 02464 SEAT PAN SHOULDER BOLT ADJUSTMENT KNOB FLAT WASHER SEAT TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location an...

8 CHECK TIRE PRESSURE The tires on your tractor were overinfl ated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.• Reduce tire pressure to PSI shown in “PRODUCT SPEC I FI CA TIONS” section of this manual. CHECK DECK LEVELNESS For best cutting r...

9 OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FOR...

10 02867 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to th...

11 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op-erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spe...

12 OPERATION TO OPERATE ON HILLS WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. 02661 AT TACH MENT CLUTCH SWITCH"DISENGAGED" PO SI TION ATTACHMENTLIFT LEVERHIGH PO SI TION ...

13 ADD GASOLINE • Fill fuel tank to bottom of fi ller neck. Do not overfi ll. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan ti...

14 FIG. 9 MOWING TIPS • Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has bee...

15 MAINTENANCE LUBRICATION CHART ➀ FRONT WHEEL BEARING ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ SPINDLE ZERK ➀ SPINDLE ZERK ➀ GENERAL PURPOSE GREASE ➁ REFER TO MAINTENANCE “ENGINE” SECTION IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LU BRI CANTS WILL...

16 MAINTENANCE BLADE REMOVAL (See Fig. 10) • Raise mower to highest position to allow access to blades. • Remove blade bolt, lock washer and fl at washer se cur ing blade. • Install new or resharpened blade with trailing edge up towards deck as shown. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOL...

17 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not ad just able. Re place belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fi ns should be kept clean to assure proper coolin...

18 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam-age. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs fi rst. Spark plug type and g...

19 SERVICE AND ADJUSTMENTS FIG. 15 TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PROD UCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower....

21 SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LE VER NEUTRAL ADJUSTMENT (See Fig. 23) The motion control lever has been pre set at the factory and adjustment should not be necessary.• Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. • Start engine and move motion c...

22 FIG. 25 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REPAIRS (See Fig. 24) • Block up axle securely.• Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble.• On rear wheels only: align grooves in rear whe...

24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open fl ame or spark. Allow the engine to cool before stor...

25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air fi lter. 5. Clean...

27 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-als and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, w...

29 15 DEGREES MAX. FOLD ALONG DO TTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL,NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mowslopes greate...

This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. For Parts and service, contact our authorized distributor: call 1-800-849-1297 • ...