Poulan PRO 188904 - Manuals

6 ASSEMBLY SHIFTROD HAIRPINCLIP SHIFTLEVERINDICATOR REMOVE TILLER FROM CRATE • Make sure shift lever indicator is in “N” position (See Fig. 7) • Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield. • Rotate tiller handle to the right and pull tiller out of carton. CO...

7 KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in li...

8 TURNING • Release the drive control bar.• Move throttle control to “SLOW” position.• Place shift lever indicator in “F” (forward) position. Tines will not turn. • Lift handle to raise tines out of ground. OPERATION 00155 HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel an...

9 OPERATION OIL LEVEL FIG. 12 BEFORE START ING ENGINE IMPORTANT : BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS. CHECK ENGINE OIL LEVEL (See Fig. 12) • The eng...

10 RUN CHOKE OPERATION • Soil conditions are important for proper tilling. Tines will not readily penetrate dry, hard soil which may con trib ute to excessive bounce and diffi cult handling of your tiller. Hard soil should be mois tened before tilling; however, extremely wet soil will “ball-up” or c...

11 MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main tain tiller as instructed in this manual. Some adjustments will need to be made periodical...

12 MAINTENANCE OIL FILLERPLUG OIL LEVEL OIL DRAINPLUG FIG. 16 Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine.Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank b...

13 MAINTENANCE engine _ar t_61 FIG. 19 AIR SCREEN BLOW ER HOUS ING MUFFLER Do not operate tiller without muffl er. Do not tamper with exhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sary. If your engine is equipped with...

14 SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into ...

16 SERVICE AND ADJUSTMENTS tine_13 FIG. 26 TINE REPLACEMENT (See Figs. 24, 25, and 26) CAUTION: Tines are sharp. Wear gloves or other protection when han- dling tines. A badly worn tine causes your tiller to work harder and dig more shallow. Most important, worn tines cannot chop and shred organic m...

17 SERVICE AND ADJUSTMENTS FIG. 27 engine_art_78 THROTTLE CONTROL CLAMP SCREW CASING AND WIRE ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 27) The throttle control has been preset at the factory and ad just ment should not be necessary. If adjustment is necessary, proceed as follows:• With engi...

18 STORAGE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remove spark plug.• Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder. • Pull starter handle slowly several times to distribute oil....

19 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait several minutes before attempting to start. 4. Dirty air cleaner. 4. Clean or replace air cleaner cartridge. 5. Water in fuel. 5. Empty fue...

20 REPAIR PARTS TILLER - - MODEL NUMBER PRRT65D HANDLE ASSEMBLY KEY PART NO. NO. DESCRIPTION 21 180517X428 Handle23 86777 Screw, Hex Washer Hd. Slotted #10-24 x 1/224 9484R Clip26 159231 Cable, Clutch27 73900400 Nut Hex Flange 1/4-20 unc29 73731000 Nut, Keps #10-24 unc 30 104164X Tie, Cable31 150696...

22 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION REPAIR PARTS TILLER - - MODEL NUMBER PRRT65D MAINFRAME, RIGHT SIDE 1 185190 Bumper 2 73970500 Locknut, Hex, Flange 5/16-183 19111116 Washer 11/32 x 11/16 x 16 Ga.4 74760512 Bolt, Hex 5/16-18 x 3/45 102332X Bracket, Reinforcement6 74760528 ...

23 12 13 15 16 14 9 9 8 5 18 23 22 21 19 18 3 2 31 7 6 5 4 11 10 29 30 28 18 32 33 34 18 48 60 24 44 18 42 43 41 49 40 39 37 38 37 50 36 20 25 27 35 25 24 44 51 58 53 52 53 transmission_19.5b KEY PART NO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 1 188554 ...

24 1 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 22 21 20 19 11 12 16 25 33 32 16 3 4 7 8 9 10 10 23 23 28 24 18 6 10 5 30 tine_shield_16_in 12 12 11 11 10 19 102701X Grip20 73220600 Nut, Hex 3/8-1621 102156X Stake, Depth22 74930632 Bolt, Hex 3/8-16 x 223 4440J Hinge24 72140404 Bolt, Carriage 1/4-...

25 2 11 11 10 9 9 4 4 5 6 7 3 3 1 2 1 1 1 9 9 8 tine_ipb_1 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 4459J Tine, Outer, L.H.2 132673 Clevis Pin3 6554J Tine, Inner, L.H.4 3146R Retainer, Spring Zinc5 132727 Assembly, Hub and Plate, L.H.6 73610600 Nut, Hex 3/8-247 10040600 Washer, Lo...

26 1 173196 Decal, CNTRL PNL 2 189872 Decal, Decal, Blt Grd 4 180816 Decal, Instruction, Tilling5 110614X Decal, Hand Placement 6 102180X Decal, Shift Indicator7 162384 Decal, caution9 120076X Decal, Warning, Rotating Tines11 173538 Decal, Rewind 13 173698 Decal, B&S Tank14 173248 Decal, B&S...

27 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-fects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, w...

Your POULAN PRO product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SERVICE OR REPLACEMENT PARTS: 1. Consult your dealer/place of purc...