Poulan PRO 115275026 - Manuals

Page 3 - IDENTIFICATION OF SAFETY SYMBOLS

3 IDENTIFICATION OF SAFETY SYMBOLS When servicing unit, use only identical replacement parts. Never allow children to operate this unit. Store unit indoors in a high, dry place out of the reach of children. Always stop unit and disconnect spark plug before clean- ing or servicing. WARNING: Fire haza...

Page 4 - OPTIONAL ATTACHMENTS; SAFETY RULES; OPERATOR SAFETY

4 OPTIONAL ATTACHMENTS Cutting attachment / guard, Powerhead model Attachments Type part. no. Trimmer head TNG 7 537419214 / 545071802 Brushcutter attachment PP4000C 952711610 Attachments Type Part. no. Edger attachment PP1000E 952711607 Cultivator attachment PP2000T 952711608 Blower attachment PP30...

Page 6 - ADDITIONAL SAFETY RULES; FOR OPTIONAL ATTACHMENTS

6 S Make sure unit is assembled correctly as shown in this manual. S Use only recommended Poulan PRO ac- cessories and replacement parts. FUEL SAFETY S Mix and pour fuel outdoors. S Keep away from sparks or flames. S Use a container approved for fuel. S Do not smoke or allow smoking near fuel or the...

Page 9 - ASSEMBLY; INSTALLING TRIMMER OR EDGER

9 S Do not run engine at high speed while not removing snow. S Be attentive when using the snowthrower, and stay alert for holes in the terrain and other hidden hazards. S Make sure the rotor will spin freely before attaching the snowthrower to the power- head. S If the rotor will not rotate freely ...

Page 10 - ATTACHING SHIELD (FOR LINE; OPERATION; KNOW YOUR TRIMMER

10 ATTACHING SHIELD (FOR LINE TRIMMER ATTACHMENT) WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others and is equipped with a line limiter blade which cuts excess line to the proper length. The line li...

Page 11 - HELPFUL TIP

11 TRIMMER HEAD The TRIMMER HEAD holds the cutting line and rotates during operation. It is designed to cut grass. BLADE The BLADE is designed to cut sod. DEPTH ADJUSTMENT KNOB The DEPTH ADJUSTMENT KNOB is used to adjust the wheel for blade cutting depth when edging. BEFORE STARTING ENGINE WARNING: ...

Page 12 - OPERATING INSTRUCTIONS

12 4. Pull starter rope handle sharply until en- gine starts and runs. 5. Allow unit to run for 10--15 seconds, then fully squeeze the throttle trigger to disen- gage the starting system. STARTING A WARM ENGINE 1. Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engi...

Page 13 - LINE TRIMMER ATTACHMENT; OPERATING POSITION

13 LINE TRIMMER ATTACHMENT OPERATING POSITION Eye Protection Long Pants Heavy Shoes ALWAYS WEAR: Cut from your right to your left. WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other seriou...

Page 14 - EDGER ATTACHMENT

14 Mowing SWEEPING -- The fanning action of the rotat- ing line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side. Sweeping EDGER ATTACHMENT OPERATING POSITION Heavy Shoes Long Pants Eye Protection ALWAYS WEAR:...

Page 15 - MAINTENANCE

15 MAINTENANCE WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. HELPFUL TIP IMPORTANT: Have all repairs other than the rec- ommended maintenance described in the instruction manual performed by an authorized service dealer. If any dealer other than ...

Page 16 - SERVICE AND ADJUSTMENTS; REPLACING THE LINE

16 SERVICE AND ADJUSTMENTS REPLACING THE LINE 1. Press the tabs on the side of the trimmer head and remove cover and spool. Tab Cover Tab Spool 2. Remove any remaining line. 3. Clean dirt and debris from all parts. Re- place spool if it is worn or damaged. 4. Replace with a pre-wound spool, or re- p...

Page 17 - REPLACING THE TRIMMER HEAD; EDGER BLADE REPLACEMENT

17 10. Insert the ends of the lines through exit holes in the sides of the cover. Line exit hole Cover 11. Reinstall the spool and cover onto the trimmer head. Push until cover snaps into place. REPLACING THE TRIMMER HEAD 1. Hold the dust cup with a wrench to keep the shaft from turning while removi...

Page 18 - STORAGE

18 CARBURETOR IDLE SPEED ADJUSTMENT WARNING: Keep others away when making idle speed adjustments. The trimmer head or any optional attachment will be spin- ning during most of this procedure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer hea...