Porter-Cable 884 - Manuals - manualsarea.com

Page 2 - GENERAL SAFETY RULES; FOR ALL BATTERY OPERATED TOOLS; WORK AREA

2 GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fireand/or serious personal injury. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER C...

Page 6 - FUNCTIONAL DESCRIPTION; FOREWORD; change direction of rotation.; ELECTRIC BRAKE; Always set reversing button to center (locked OFF) position

6 FUNCTIONAL DESCRIPTION FOREWORD Your Porter-Cable Cordless Driver/Drill is designed to drill holes and drivefasteners in various materials as indicated in the following chart: SWITCH OPERATION Squeeze trigger switch (A) Fig. 1, tostart motor. Release trigger to stopmotor. As the trigger is squeeze...

Page 7 - ADJUSTING TORQUE COLLAR

7 3. Clean and insert smooth end of bit as far as it will go into the chuck, or up to the flutes for small bits. 4. While holding the bit with one hand, turn outer sleeve (A) Fig. 2, clockwise until the bit is gripped in the chuck. 5. Tighten chuck by holding chuck ring (B) Fig. 2, with one hand whi...

Page 8 - OPERATION; CHARGING THE BATTERY PACK GENERAL; Battery temperature will increase during and shortly after use.; NORMAL CHARGING; Disconnect charger from power source when not in use.; DIAGNOSTICS

8 OPERATION CHARGING THE BATTERY PACK GENERAL Before using your cordless Driver/Drill for the first time, the battery packshould be fully charged. If the battery pack is installed in the Driver/Drill,remove it by following instructions under INSTALLING OR REMOVINGBATTERY PACK. As a battery pack appr...

Page 9 - The front end of the Driver/Drill may be made live if the tool; GENERAL DRILLING; Be sure drill bit is securely gripped in chuck.; A B

9 • Green light (A) glows continuously and red light (B) flashes: indicates that the battery pack is receiving a “Fast Charge”, but the battery pack voltage islow. It is not unusual for a new, or a fully discharged battery pack to give thisindication for the first several minutes of charge. If the r...

Page 10 - DRILLING WOOD; IT’S

10 3. Set REVERSING BUTTON for clockwise rotation. 4. CAUTION: Make sure work is held securely in vise or clamped in place prior to starting drilling operation. Loose work may spin and cause bodilyinjury. 5. Locate exact center for hole to be drilled and using a center punch, make a small dent in wo...

Page 11 - IT’S A; SUGGESTED HOLE SIZES

11 DRILLING METAL In addition to the instructions listed under GENERAL DRlLLlNG, the followingalso apply: 1. Use only good quality sharp high speed steel twist bits when drilling metal. 2. Start drilling with slow speed and gradually increase speed as drill cuts. The harder the material, the slower ...

Page 12 - MAINTENANCE

12 DRIVING SELF-TAPPING SCREWS 1. Drill pilot hole of correct size as recommended by screw manufacturer for fastener being used. 2. Install proper bit that fits screw to screwdriver. 3. Set torque adjusting collar for desired torque and set speed selector to LOW. 4. Set screwdriver for correct rotat...

Page 13 - REMOVE

13 CHUCK REPLACEMENT 1. CAUTION: Remove battery pack to prevent accidental start-up. 2. Open chuck jaws as wide as possible to gain access to the chuck retaining screw. 3. Remove chuck retaining screw by turning it clockwise (left-hand thread) with an allen wrench. 4. Place the two-speed gear shift ...

Page 14 - ACCESSORIES; Since accessories other than those listed have not been

14 ACCESSORIES The testing of this tool has been accomplished with the following accessories.For safest operation, it is recommended that only these accessories be usedwith this product. WARNING: Since accessories other than those listed have not been tested with this product, use of such accessorie...

Page 15 - ONE YEAR WARRANTY

15 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...

Page 16 - NOTES

NOTES 900469 - 11-30-00.QXD 9/25/02 11:26 AM Page 16

Page 17 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE · DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE · DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE · DELTA Corporation): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PO...