Porter-Cable 7418 - Manuals

Page 2 - GENERAL SAFETY RULES; WORK AREA

2 GENERAL SAFETY RULES WARNING: READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/orserious personal injury. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, G R I N D I N G , D R I L L I N G , A N D O T H E R C O N S T ...

Page 4 - SPECIFIC SAFETY RULES AND SYMBOLS; SYMBOL

4 SPECIFIC SAFETY RULES AND SYMBOLS 1. ALWAYS USE PROPER GUARD WITH GRINDING WHEEL. A guard protects operator from broken wheel fragments. 2. A C C E S S O R I E S M U S T B E R A T E D F O R A T L E A S T T H E S P E E D RECOMMENDED ON THE TOOL WARNING LABEL. Wheels and other accessories running ov...

Page 5 - ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

5 ______ – – – – .......................... alternating current 3 .......................... three-phase alternating current 3 N .......................... three-phase alternating current with neutral .......................... direct current n 0 .......................... no load .....................

Page 6 - CLEAN UP ALL REMOVED PAINT; and dust by wet mopping the floors.; AT THE END OF EACH WORK SESSION; put the paint chips and debris; REMOVE PROTECTIVE CLOTHING; and work shoes in the work area to; REPLACEMENT PARTS; When servicing use only identical replacement parts.; MOTOR; Do not operate your tool on a circuit on which the; EXTENSION CORD SELECTION

6 8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint ordust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a highphosphate detergent or trisodium (TSP) to wash and mop areas. 9. AT THE END OF EACH WORK SE...

Page 7 - FUNCTIONAL DESCRIPTION; FOREWORD; Make sure switch is OFF and power circuit voltage is the; ASSEMBLY; TO INSTALL AUXILIARY HANDLE; The cover of the auxiliary handle (A) Fig. 3 can be removed to

7 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable disc grinders are designed for numerous grinding operations.Typical applications are auto body grinding, smoothing welding beads,removing gates and flash from castings, and removing rust. TO START AND STOP THE MACHINE CAUTION: Make sure switch is OFF an...

Page 8 - TO INSTALL WHEEL GUARD; TYPE 1; TO INSTALL GRINDING WHEEL

TO INSTALL WHEEL GUARD A TYPE 27 wheel guard is furnished with the tool. A TYPE 1 wheel guard is available as an accessory for cut-off wheels. Both guards are installed andadjusted in the same manner. WARNING: Always use an approved, and properly adjusted wheel guard where required (see ACCESSORIES ...

Page 9 - OPERATION; USING A DISC GRINDER

4. Position inner flange (A) Fig. 6 onto spindle (B), with round hub facing outward, away from machine. Rotate flange until it drops into place on thespindle. CAUTION: Use Type 1 Wheel Guard when using Type 1 cut-off Wheels. 5. Position grinding wheel on spindle. 6. Position outer flange (A) Fig.7 o...

Page 10 - MAINTENANCE; KEEP TOOL CLEAN; Wear safety glasses while using compressed air.; FAILURE TO START

MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plasticparts should be cleaned with a soft damp cloth. NEVER use solvents toclean plastic parts. They could possibly dissolve or otherwise damage thematerial. CAUTION: Wear safety glasses while using comp...

Page 11 - ACCESSORIES; Delta Factory Service Centers, and; ONE YEAR WARRANTY

ACCESSORIES A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. WARNING:...

Page 12 - NOTES

12 NOTES 300918- 08-13-02.qxd 9/13/02 3:26 PM Page 12