Porter-Cable 7406 - Manuals

Page 2 - GENERAL SAFETY RULES; WORK AREA

2 WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, G R I N D I N G , D R I L L I N G , A N D O T H E R C O N S T R U C T I O N A C T I V I T I E S c o n t a i n s c h e m i c a l s k n o w n t o c a u s e c a n c e r , b i r t h d e f e c t s o r o t h e rreproductive harm. Some examples of thes...

Page 4 - SPECIFIC SAFETY RULES AND SYMBOLS; SYMBOL

4 SPECIFIC SAFETY RULES AND SYMBOLS 1. H o l d t o o l b y i n s u l a t e d g r i p p i n g s u r f a c e s w h e n p e r f o r m i n g a n operation where the cutting tool may contact hidden wiring or its owncord. Contact with a “live” wire will also make exposed metal parts of the tool “live” and...

Page 5 - ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

n 0 .......................... no load .......................... alternating or direct current .......................... Class II Construction .......................... splash-proof construction .......................... watertight construction …/min .......................... revolutions or rec...

Page 6 - CLEAN UP ALL REMOVED PAINT; and dust by wet mopping the floors.; AT THE END OF EACH WORK SESSION; put the paint chips and debris; REMOVE PROTECTIVE CLOTHING; and work shoes in the work area to; MOTOR; Do not operate your tool on a current on which the; EXTENSION CORD SELECTION

6 8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint ordust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a highphosphate detergent or trisodium (TSP) to wash and mop areas. 9. AT THE END OF EACH WORK SE...

Page 7 - FUNCTIONAL DESCRIPTION; FOREWORD; ASSEMBLY; TO INSTALL WHEEL GUARD; TYPE 1

FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable disc grinders are designed for numerous grinding operations.Typical applications are auto body grinding, smoothing welding beads,removing gates and flash from castings, removing rust and the like! TO START AND STOP THE MACHINE CAUTION: Make sure switch is...

Page 8 - A l w a y s m a k e s u r e t h e w h e e l g u a r d i s p o s i t i o n e d; TO INSTALL GRINDING WHEEL; DISCONNECT TOOL FROM POWER SOURCE.

8 3. Position the appropriate guard to the machine so that the three bosses (inside the guard mounting clamp) are aligned with the three notches in themounting flange of the grinder (see Fig. 3). 4. Seat guard onto mounting flange. Rotate the guard to a position that will place the guard between the...

Page 10 - OPERATION; USING A DISC GRINDER; Be certain wheel guard and auxiliary handle are installed.; MAINTENANCE; KEEP TOOL CLEAN; Wear safety glasses while using compressed air.; FAILURE TO START

10 4. Push retaining nut hub through an abrasive disc and position to spindle. Thread nut onto spindle finger tight. 5. Depress spindle lock pin (E) Fig. 10, and hold while rotating backup pad clockwise by hand until spindle lock engages. 6. While continuing to hold spindle lock pin engaged, grasp t...

Page 11 - ACCESSORIES

11 BRUSH INSPECTION AND LUBRICATION For your continued safety and electrical protection, brush inspection andreplacement on this tool should ONLY be performed by an AUTHORIZEDP O R T E R - C A B L E S E R V I C E S T A T I O N o r a P O R T E R - C A B L E / D E L T AFACTORY SERVICE CENTER. At appro...

Page 12 - ONE YEAR WARRANTY

12 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...