Porter-Cable 6603 - Manuals

Page 3 - CALIFORNIA PROPOSITION 65; SAFETY GUIDELINES - DEFINITIONS

3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silic...

Page 4 - GENERAL SAFETY RULES

4 R e a d a l l i n s t r u c t i o n s . F a i l u r e t o f o l l o w a l l instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (c...

Page 6 - ADDITIONAL SPECIFIC SAFETY RULES; SAVE THESE INSTRUCTIONS!

6 1. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its owncord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Keep hands away from cutting area. ...

Page 7 - IPXX

7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litre...

Page 8 - EXTENSION CORD SELECTION; MOTOR; Do not operate your tool on a current on which the; CARTON CONTENTS

8 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough toprevent excessive voltage drop which will cause loss of power and possiblemotor damage. A table of recommended extension cord sizes will be found inthis section. This table is based on limiting li...

Page 9 - FOREWORD; Shear is designed for cutting cold-rolled steel; HOW TO HOLD THE SHEAR; M a k e s u r e t h a t t h e p o w e r; FUNCTIONAL DESCRIPTION

9 FOREWORD The Porter-Cable Model 6603 Shear is designed for cutting cold-rolled steel sheets up to 18 Ga. and stainless steel sheets up to 20 Ga. You can makeboth straight and curved cuts with a minimum radius of 7". The Shearremoves a ¼ " wide continuous curl of waste material without bend...

Page 10 - The lock button can be engaged only when the drill is running at; HOW TO USE SHEAR; REMOVING CUTTER BLADES

10 TO LOCK the trigger switch “ON”, squeeze the trigger as far as it will go,push in the lock button and release the trigger. TO UNLOCK the lock button, squeeze the trigger and release, leaving thelock button free to spring out. NOTE: The lock button can be engaged only when the drill is running at ...

Page 11 - INSTALLING CUTTER BLADES; For Model 6605, change the side knives after they show a width wear; DISCONNECT TOOL FROM POWER SOURCE.

11 INSTALLING CUTTER BLADES NOTE: For Model 6605, change the side knives after they show a width wear pattern of fifty percent (50%).Swap the knives left to right and use them untilthe patterns meet. When the patterns meet, invert the left and right sideknives and use them until they show a width we...

Page 12 - SERVICING THE ECCENTRIC BEARING

12 SERVICING THE ECCENTRIC BEARING NOTE: For model 6603 only. Once every three months (depending on usage), remove the shear headf r o m t h e p o w e r u n i t f o l l o w i n g t h e i n s t r u c t i o n s i n t h e " R E P L A C I N GCUTTERS" section of the manual. Disconnect the tool fr...

Page 13 - KEEP TOOL CLEAN; Wear ANSI Z87.1 safety glasses while using compressed air.; FAILURE TO START; DELTA FACTORY; MAINTENANCE; For assistance with your tool, visit our website at; TROUBLESHOOTING

KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic partsshould be cleaned with a soft damp cloth. NEVER use solvents to clean plasticparts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed ai...

Page 14 - REPLACEMENT PARTS; SERVICE

14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...