Porter-Cable 6602 - Manuals

Page 2 - GENERAL SAFETY RULES; WORK AREA

2 WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, G R I N D I N G , D R I L L I N G , A N D O T H E R C O N S T R U C T I O N A C T I V I T I E S c o n t a i n s c h e m i c a l s k n o w n t o c a u s e c a n c e r , b i r t h d e f e c t s o r o t h e rreproductive harm. Some examples of thes...

Page 4 - SPECIFIC SAFETY RULES AND SYMBOLS FOR SHEARS; SYMBOL

4 SPECIFIC SAFETY RULES AND SYMBOLS FOR SHEARS 1. ALWAYS hold the tool as instructed in HOW TO HOLD TOOL section. This will prevent accidental shock resulting from cutting a live wire whencutting into a wall or other blind area. 2. KEEP hands away from cutting area. 3. ALWAYS use sharp cutting tools...

Page 5 - FUNCTIONAL DESCRIPTION; FOREWORD

REPLACEMENT PARTS When servicing use only identical replacement parts. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60cycle A.C. current and voltage within plus or minus 5 percent of that shownon the specification plate on the tool. Several models, however, are de...

Page 6 - OPERATION; HOW TO HOLD SHEAR; The gear housing, intermediate plate, and cutting; TO START AND STOP SHEAR; Make sure switch is in OFF position and hands, body and

6 Fig. 1 OPERATION HOW TO HOLD SHEAR WARNlNG: The gear housing, intermediate plate, and cutting head may be made live if the tool cuts into live wiring. To preventaccidental shock, the tool must be held as shown in Fig. 1. TO START AND STOP SHEAR CAUTION: Make sure switch is in OFF position and hand...

Page 7 - Replacement cutters are installed as follows:

7 HOW TO USE SHEAR Model 6602: B e s u r e t h e m a t e r i a l t o b e s h e a r e d i s f i r m l y s u p p o r t e d . C l a m p i n g i srecommended to insure control of the tool and the workpiece. Place sideknives of shear slightly on the edge of the top side of the workpiece tosteady tool. Sq...

Page 8 - Coat center blade yoke area with; MAINTENANCE; KEEP TOOL CLEAN; Wear safety glasses while using compressed air.; FAILURE TO START

8 1. Place the side knives (D) and (E) back into the shear housing, insert a capscrew through center hole in shear housing, side knife (E), spacer bushing(C), side knife, (D), and thread screw into housing threads one or two turns.DO NOT TIGHTEN. 2. Coat remaining spacer bushing (C) with lubricant a...

Page 9 - SERVICING THE ECCENTRIC BEARING; NOTE: For model 6602 only, Model 6604 does not require this service.; DISCONNECT TOOL; SERVICE AND REPAIRS; ACCESSORIES; Delta Factory Service Centers, and; Since accessories other than those offered by; P o r t e r - C a b l e; Delta

9 SERVICING THE ECCENTRIC BEARING (see Fig. 4) NOTE: For model 6602 only, Model 6604 does not require this service. Once every three months, dependingupon usage, remove the shear headf r o m t h e p o w e r u n i t f o l l o w i n g t h ei n s t r u c t i o n s i n t h e R E P L A C I N GCUTTERS sec...

Page 10 - ONE YEAR WARRANTY

10 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...