Porter-Cable 4630 - Manuals

Page 3 - CALIFORNIA PROPOSITION 65; SAFETY GUIDELINES - DEFINITIONS

3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silic...

Page 4 - GENERAL SAFETY RULES

4 R e a d a l l i n s t r u c t i o n s . F a i l u r e t o f o l l o w a l l instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (c...

Page 6 - ADDITIONAL SPECIFIC SAFETY RULES; Never; To do

6 ADDITIONAL SPECIFIC SAFETY RULES SAVE THESE INSTRUCTIONS! 1. Hold power tools by insulated gripping surfaces when performingan operation where the cutting tool may contact hidden wiring or itsown cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and ...

Page 7 - for the time/current characteristic, as given in IEC 60127; IPXX; symbol; SAVE THESE INSTRUCTIONS!; EXTENSION CORD SELECTION; MOTOR; Do not operate your tool on a current on which the

7 2 ........................ two-phase alternating current 2 N ........................ two-phase alternating current with neutral 3 ........................ three-phase alternating current 3 N ........................ three-phase alternating current with neutral ........................ rated curre...

Page 8 - FOREWORD; FUNCTIONAL DESCRIPTION; TO START AND STOP THE TOOL

8 FOREWORD Porter-Cable screwdrivers are designed to install or remove various sizes andtypes of fasteners. FUNCTIONAL DESCRIPTION CARTON CONTENTS Carton contents include the screwdriver, an instruction manual, and a parts list. NOTE: This tool is shipped completely assembled. No assembly time or to...

Page 9 - DISCONNECT TOOL FROM POWER SOURCE.; ADJUST DEPTH STOP –; STEPS 1; TO CHANGE HEX NUTSETTER –

9 Never attempt to change direction of rotation while the switchis “ON” . To do so, may damage interlock feature built into switch. Be sure that the switch is “OFF” and the motor has completely stopped before changing the direction of rotation. 4. VARIABLE SPEED – As the trigger switch is squeezed, ...

Page 10 - CHANGE BIT HOLDER –; A D J U S T D E P T H S T O P ,; Do not push the bit holder in.; DRIVING DRYWALL SCREWS –

10 CHANGE BIT HOLDER – MODELS 4630, 4634 DISCONNECT TOOL FROM POWER SOURCE. 1. Pull the Depth Stop Assembly (A)Fig. 4 from the clutch housing. 2. Pull the bit holder (C) Fig. 4 out. Ifit is difficult to remove, grip it withpliers and pull. NOTE: You can remove the bit (B) Fig. 4 from the bit holder ...

Page 11 - TO REMOVE SCREWS – ALL MODELS; TROUBLESHOOTING; CHECK CLUTCH CONDITION

11 DRIVING SELF-DRILLING/TAPPING SCREWS – MODELS 4640 NOTE: Maximum size screws for use with this tool are #12 wood screws and 1/4" self-drilling/tapping screws. These screws drill and tap their own hole as they are driven. This differs fromself-tapping screws in that pre-drilled holes for tappi...

Page 12 - BRUSH INSPECTION; DELTA FACTORY; KEEP TOOL CLEAN; Wear ANSI Z87.1 safety glasses while using compressed air.; FAILURE TO START; The clutch housing is attached to the power unit with

12 BRUSH INSPECTION (If applicable) For your continued safety and electrical protection, brush inspection andreplacement on this tool should ONLY be performed by an AUTHORIZEDPORTER-CABLE SERVICE STATION or a PORTER-CABLE • DELTA FACTORY SERVICE CENTER. At approximately 100 hours of use, take or sen...

Page 13 - REPLACEMENT PARTS

13 SERVICE A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since acc...