Planet WGSW-24040R - Manuals

Page 3 - TABLE OF CONETNTS

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 3 TABLE OF CONETNTS 1. INTRODUTION .................................................................................................................... 12 1.1 Packet Contents .............................................................

Page 12 - Product Description; Center Networking

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 12 1. INTRODUTION The PLANET Layer 2 Managed Gigabit Switch series - WGSW-24040 / WGSW-24040R / SGSW-24040 / SGSW-24040R are all multiple ports Gigabit Ethernet Switched with SFP fiber optical connective ability and robust layer 2 fe...

Page 14 - Reliability Stacking Management; setting each unit one by one.; it gives enterprise, service; Ethernet ports can be managed by a stacking group and; you can add ports and functionality as needed. The stacking; AC / DC Power Redundant to ensure continuous operation; How to Use This Manual; The section describes how to use the Command Line interface (CLI).

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 14 Reliability Stacking Management The SGSW Series Managed Switch provides a switch stacking function to manage up to 16 switches using a single IP address. That helps network managers to easily configure switches via one single IP a...

Page 15 - Product Features; Physical Port

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 15 1.4 Product Features ¾ Physical Port WGSW-24040 / WGSW-24040R 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 4 mini-GBIC/SFP slots , shared with Port-21 to Port-24 RS-232 DB9 console interface for Switch basic management a...

Page 17 - Product Specification; Hardware Specification; K entries; Layer 2 function; Bandwidth control on each port.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 17 1.5 Product Specification Product WGSW-24040 WGSW-24040R SGSW-24040 SGSW-24040R Hardware Specification Copper Ports 24 10/ 100/1000Base-T RJ-45 Auto-MDI/MDI-X ports SFP/mini-GBIC Slots 4 SFP interfaces, shared with Port-21 to Port...

Page 18 - Access Control List; FCC Part 15 Class A, CE

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 18 Port trunking IEEE 802.3ad LACP / Static Trunk Support 8 groups of 8-Port trunk support QoS Traffic classification based, Strict priority and WRR 4-level priority for switching - Port Number - 802.1p priority - DS/TOS field in IP ...

Page 19 - read this chapter completely.; Hardware Description; and; Gigabit TP interface; and so on) to enter the statup screen of the device.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 19 2. INSTALLATION This section describes the hardware features and installation of the Managed Switch on the desktop or rack mount. For easier management and control of the Managed Switch, familiarize yourself with its display indic...

Page 21 - monitor and troubleshoot when needed.; to indicate that the Switch is powered on.; Green; If 1000 LNK/ACT LED Off -> indicate that the port is link down

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 21 2.1.2 LED Indications The front panel LEDs indicates instant status of port links, data activity, system operation, Stack status and system power, helps monitor and troubleshoot when needed. WGSW-24040 / WGSW-24040R LED indication...

Page 23 - LED; speed; LNK; To indicate that the SFP port is link down; -Segment LED Display; To indicate the; Switch ID; shows the rear panel of these Managed Switches

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 23 Lights: To indicate the link through that port is successfully established with speed 10Mbps or 100Mbps Blink : To indicate that the switch is actively sending or receiving data over that port. 10/100 LNK/ACT Orange Off: If 1000 L...

Page 25 - position and the DC power is; OFF

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 25 Figure 2-9 SGSW-24040 / SGSW-24040R Stack Ports ■ DC Power Connector The rear panel of the WGSW-24040R and SGSW-24040R contains a power switch and a DC power connector, which accepts DC power input voltage from -30V to -60V DC. Co...

Page 26 - Install the Switch; simply complete the following steps.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 26 2.2 Install the Switch This section describes how to install your Managed Switch and make connections to the Managed Switch. Please read the following topics and perform the procedures in the order being presented. To install your...

Page 30 - Pull out the SFP transceiver

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 30 Figure 2-14 Pull out the SFP transceiver Never pull out the module without pull the handle or the push bolts on the module. Direct pull out the module with violent could damage the module and SFP module slot of the Managed Switch.

Page 31 - OFF”

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 31 2.2. 4 Connecting DC Power Supply – WGSW-24040R / SGSW-24040R The WGSW-24040R and SGSW-24040R support -48VDC power input, connect the power cable to the switch at the input terminal block. 1. The size of the two screws in the term...

Page 32 - Stack Installation; fabric will scale to meet increasing traffic demands.; Chain topology (same as a disconnected ring); Please find the following picture for sample connection.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 32 2.3 Stack Installation SGSW-24040 / SGSW-24040R The SGSW-24040 series Managed Switch provides a switch stacking function to manage up to 16 switches using a single IP address. And up to 384 Gigabit Ethernet ports can be managed by...

Page 34 - indicated by a lit green “; Master; ” LED on the front panel. As the; PLANET Smart Discovery Utility; to displayt the IP address of the

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 34 STEP-5 : Once the stack start operation, the Stack master be automatically elected without any configure. The Stack master is indicated by a lit green “ Master ” LED on the front panel. As the Figure 2-19 appears. Figure 2-19 Stac...

Page 36 - SWITCH MANAGEMENT

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 36 3. SWITCH MANAGEMENT This chapter explains the methods that you can use to configure management access to the Managed Switch. It describes the types of management applications and the communication and management protocols that de...

Page 37 - Management Access Overview; Console; Administration Console

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 37 3.2 Management Access Overview The Managed Switch gives you the flexibility to access and manage it using any or all of the following methods: An administration console Web browser interface An external SNMP-based network ma...

Page 38 - Console management; Direct Access; HyperTerminal; When using this management method, a; data bits; Terminal parameter settings

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 38 Figure 3-1 Console management Direct Access Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal ) to the Managed Switc...

Page 39 - Web management; Microsoft; or

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 39 3.4 Web Management The Managed Switch offers management features that allow users to manage the Managed Switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. After you set up your IP a...

Page 40 - SNMP-Based Network Management; same community string; Protocols; .1 Virtual Terminal Protocols; Telnet

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 40 3. 5 SNMP-Based Network Management You can use an external SNMP-based application to configure and manage the Managed Switch, such as SNMPc Network Manager, HP Openview Network Node Management (NNM) or What’s Up Gold. This managem...

Page 41 - Start the Telnet program on a PC and connect to the Managed Switch.; SNMP Protocol

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 41 2. Start the Telnet program on a PC and connect to the Managed Switch. The management interface is exactly the same with RS-232 console management. 3. 6. 2 SNMP Protocol Simple Network Management Protocol (SNMP) is the standard ma...

Page 42 - WEB CONFIGURATION; About Web-based Management; IP subnet address with the Managed Switch.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 42 4. WEB CONFIGURATION This section introduces the configuration and functions of the Web-Based management. About Web-based Management The Managed Switch offers management features that allow users to manage the Managed Switch from ...

Page 43 - Logging on the switch; factory-default IP Address as following:; Login screen; admin

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 43 Logging on the switch 1. Use Internet Explorer 6.0 or above Web browser. Enter the factory-default IP address to access the Web interface. The factory-default IP Address as following: http://192.168.0.100 2. When the following l...

Page 44 - Save; button, you need to

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 44 Figure 4-1-3 Default main page Now, you can use the Web management interface to continue the switch management or manage the Managed Switch by Web interface. The Switch Menu on the left of the web page let you access all the comma...

Page 45 - Panel Display; The port states are illustrated as follows:; State

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 45 4.1 Main WEB PAGE The WGSW / SGSW Managed Switch provides a Web-based browser interface for configuring and managing it. This interface allows you to access the Managed Switch using the Web browser of your choice. This chapter des...

Page 46 - Main Menu; those listed in the Main Function. The screen in

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 46 Main Menu Using the onboard web agent, you can define system parameters, manage and control the Managed Switch, and all its ports, or monitor network conditions. Via the Web-Management, the administrator can setup the Managed Swit...

Page 48 - SNTP Server

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 48 4.2.1 System Information The System Info page provides information for the current device information. System Info page helps a switch administrator to identify the hardware MAC address, software version and system uptime. The scr...

Page 50 - SNTP; dotted decimal notation; VLAN ID; VLAN

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 50 4.2.2 IP Configuration The IP Configuration includes the IP Address, Subnet Mask and Gateway. The Configured column is used to view or change the IP configuration.Fill up the IP Address, Subnet Mask and Gateway for the device. The...

Page 51 - “Save”; User Authentication page screenshot; Object; and are case sensitive.; Confirm New; “Reset”

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 51 : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. 4.2.3 User Authentication This page allows you to configure the system password required to access the web pages or log in fr...

Page 53 - Software successfully loaded notice screen

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 53 It is recommended that you research any time server selection to ensure that it can meet your specific time server requirements. Any NTP time server selection should be evaluated to determine if the server in question meets your s...

Page 56 - Configuration Save; Configuration Download:; Figure

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 56 4.2. 7 Configuration Save This function allows backup and reload the current configuration of the Managed Switch to the local management station. The screen in Figure 4-2-10 appears. Figure 4-2-10 Configuration Save page screensho...

Page 57 - File save screen; screen in; Configuration Upload:; saved at the local machine already.; Configuration Upload

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 57 Figure 4-2-12 File save screen 4.2. 8 Configuration Upload This function allows backup and reload the current configuration of the Managed Switch to the local management station. The screen in Figure 4-2-13 appears. Figure 4-2-13 ...

Page 58 - Upload; ”, the bottom of the browser shows the upload status.; Transfer Completed

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 58 Figure 4-2-14 Windows file selection menu popup 2. Select on the configuration file then click “ Upload ”, the bottom of the browser shows the upload status. 3. After down, the main screen appears “ Transfer Completed ”.

Page 59 - Factory Default; Factory Default Reset screen; Factory; The other setting value is back to disable or none.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 59 4.2. 9 Factory Default The Factory Reset button can reset the VDSL2 Switch back to the factory default mode. Be aware that the entire configuration will be reset; include the IP address of the VDSL2 Switch. Once the Factory Reset ...

Page 60 - System Reboot; The; Reboot; re-login the WEB interface about 60 seconds later, the screen in; SYS LED

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 60 4.2.1 0 System Reboot The Reboot page enables the device to be rebooted from a remote location. Once the Reboot button is pressed, user have to re-login the WEB interface about 60 seconds later, the screen in Figure 4-2-16 appears...

Page 61 - Example 1: Save Current Configuration setting; automatically across a system reboot.; Copy Operation; ” as the file transfer method.; Apply; Configuration saving screenshot

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 61 Example 1: Save Current Configuration setting To save all applied changes and set the current configuration as startup configuration. The startup-configuration file will be load automatically across a system reboot. 1. Click Sys...

Page 62 - Example 2: Downloading System Software from a Server; ” as the file transfer method, enter the

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 62 Example 2: Downloading System Software from a Server When downloading runtime code, you can specify the destination file name to replace the current image, or first download the file using a different name from the current runti...

Page 63 - Example 3: Downloading Configuration Settings from a Server; IP address; of the TFTP server.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 63 • If you download to a new destination file, go to the System / File / Set Start-Up menu, mark the operation code file used at startup, and click Apply. • To start the new firmware, reboot the system via the System / Reset menu. •...

Page 64 - Reset; Example 4: Saving or Restoring Configuration Settings; You can upload/download; configuration settings; restore the Managed Switch’s settings.; ” or “; startup-config to tftp; of the TFTP; Upload system configuration screenshot

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 64 configuration file. To use the new settings, reboot the system via the System / Reset menu. Example 4: Saving or Restoring Configuration Settings You can upload/download configuration settings to/from a TFTP server. The configur...

Page 65 - Simple Network Management Protocol; SNMP

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 65 4.3 Simple Network Management Protocol 4.3.1 SNMP Overview The Simple Network Management Protocol (SNMP) is an application layer protocol that facilitates the exchange of management information between network devices. It is part ...

Page 67 - SNMP System Information Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 67 4.3.3 SNMP System Information Configuration The switch system information is provided here. The System Information Configuration screen in Figure 4-3-2 appears. Figure 4-3-2 System Information Configuration page screenshot The pag...

Page 74 - excluded; : An optional flag to indicate that this view subtree should be; OID Subtree; EXAMPLE: Add a new SNMPv3 user; In the New User page, define a name and assign it to a group, then click; Add; to save the configuration and return to the

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 74 • View Type Indicates the view type that this entry should belong to. Possible view type are: • included : An optional flag to indicate that this view subtree should be included. • excluded : An optional flag to indicate that this...

Page 75 - EXAMPLE: Add a new SNMPv3 Group; In the; New Group page; to save the new group and return to the Groups list.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 75 Figure 4-3-9 SNMPv3 Users-NEW page screenshot Once the new SNMPv3 user be successed add and be assign to a snmp group, this entry will shows in the users table. Figure 4-3-10 SNMPv3 Users page screenshot EXAMPLE: Add a new SNMPv...

Page 76 - SNMPv3 Groups-NEW page screenshot

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 76 Figure 4-3-11 SNMPv3 Groups-NEW page screenshot

Page 77 - Port Configuration; Configures port connection settings; Port Statistics; Lists Ethernet and RMON port statistics; Mirror Port Configuration; Sets the source and target ports for mirroring

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 77 4.4 Port Management Use the Port Menu to display or configure the Managed Switch's ports. This section has the following items: Port Configuration Configures port connection settings Port Statistics Lists Ethernet and RMON por...

Page 79 - Enabled; : Link up and link down power savings enabled.; Total Power Usage; Total power usage in board, measured in percent.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 79 • Enabled : Link up and link down power savings enabled. • Total Power Usage Total power usage in board, measured in percent. When set each port to run at 100M Full, 100M Half, 10M Full, and 10M Half-speed modes. The Auto-MDIX fun...

Page 81 - Receive Total and Transmit Total; Receive and Transmit Size Counters; Short frames are frames that are smaller than 64 bytes.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 81 The page includes the following fields: Receive Total and Transmit Total Object Description • Rx and Tx Packets The number of received and transmitted (good and bad) packets • Rx and Tx Octets The number of received and transmitte...

Page 82 - Transmit Error Counters

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 82 Transmit Error Counters Object Description • Tx Drops The number of frames dropped due to output buffer congestion. • Tx Late/Exc. Coll. The number of frames dropped due to excessive or late collisions. 4.4.4 Port Mirroring Config...

Page 83 - Port to mirror to

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 83 Mirror Port Configuration The Port Mirror Configuration screen in Figure 4-4-5 and Figure 4-4-6 appears. WGSW Standalone Switch Figure 4-4-5 Port Mirror Configuration page screenshot The page includes the following fields: Objec...

Page 84 - SGSW Stackable Switch; Port Mirror Configuration page screenshot; mirrored to this switch.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 84 SGSW Stackable Switch The SGSW Stackable switch supports port mirror function over stack switch. Figure 4-4-6 Port Mirror Configuration page screenshot Object Description • Switch to mirror to Frames from ports that have either ...

Page 85 - Link Aggregation

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 85 4.5 Link Aggregation Port Aggregation optimizes port usage by linking a group of ports together to form a single Link Aggregated Groups (LAGs). Port Aggregation multiplies the bandwidth between the devices, increases port flexibil...

Page 87 - Hash Code Contributors; Aggregation Mode Configuration page screenshot; to disable. By default, Destination MAC Address is disabled.; IP Address; Static Aggregation Group Configuration; The Aggregation Group Configuration screen in

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 87 4.5.1 Static Aggregation Configuration This page is used to configure the Aggregation hash mode and the aggregation group. The aggregation hash mode settings are global, whereas the aggregation group relate to the currently select...

Page 90 - LACP

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 90 each second, while Passive will wait for a LACP packet from a partner (speak if spoken to). 4.5.3 LACP System Status This page provides a status overview for all LACP instances. The LACP Status page display the current LACP aggreg...

Page 93 - Private VLAN; Creates/removes primary or community VLANs

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 93 4.6 VLAN 4.6.1 VLAN Overview A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical layout. VLAN can be used to combine any collection of LAN segments into an au...

Page 95 - Tagging; presence is indicated by a value of

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 95 ports and work normally. Any port can be configured as either tagging or untagging. The untagging feature of IEEE 802.1Q VLAN allow VLAN to work with legacy switches that don’t recognize VLAN tags in packet headers. The tagging fe...

Page 96 - Port VLAN ID; PVID is not used to make packet forwarding decisions, the VID is.; Default VLANs; The factory default setting assigns all ports on the Switch to; Assigning Ports to VLANs

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 96 Adding an IEEE802.1Q Tag Dest. Addr. Src. Addr. Length/E. type Data Old CRC Dest. Addr. Src. Addr. E. type Tag Length/E. type Data New CRC Priority CFI VLAN ID ■ Port VLAN ID Packets that are tagged (are carrying the 802.1Q VID in...

Page 97 - VLAN Classification; them by enabled routing on this switch.; Untagged VLANs

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 97 VLANs, and any intermediate network devices or the host at the other end of the connection supports VLANs. Then assign ports on the other VLAN-aware network devices along the path that will carry this traffic to the same VLAN(s), ...

Page 99 - tagged

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 99 4.6.4 VLAN Port Configuration This page is used for configuring the Managed Switch port VLAN. The VLAN per Port Configuration page contains fields for managing ports that are part of a VLAN. The port default VLAN ID (PVID) is conf...

Page 103 - Overview; application examples are provided in this section:; Promiscuous ports; — Ports which can receive traffic from all ports in the private VLAN; Isolated ports; just the promiscuous ports within the private VLAN.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 103 4.6.6 Private VLAN Configuration Overview When a VLAN is configured to be a private VLAN, communication between ports within that VLAN can be prevented. Two application examples are provided in this section: • Customers connected...

Page 105 - Rapid Spanning Tree Protocol; IEEE 802.1W Rapid Spanning Tree

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 105 4.7 Rapid Spanning Tree Protocol The Spanning Tree protocol can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers. This allows the switch to interact with other bridging...

Page 109 - chosen to forward packets.; Illustration of STP; some major network problems if the STP assistance is not applied.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 109 the Root Bridge, the set Hello Time will be used if and when your Switch becomes the Root Bridge. The Hello Time cannot be longer than the Max. Age. Otherwise, a configuration error will occur. Max. Age – The Max Age can be from ...

Page 110 - After Applying the STA Rules

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 110 Bridge ID = 15 Port 3 Port 1 Port 2 A Bridge ID = 20 Port 1 Port 2 Port 3 C Bridge ID = 30 Port 1 Port 2 Port 3 B LAN 1 LAN 2 LAN 3 Portcast = 19 Portcast = 19 Portcast = 19 Portcast = 4 Portcast = 4 Portcast = 19 Portcast = 4 Po...

Page 111 - RSTP System Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 111 4.7. 1 RSTP System Configuration This page allows you to configure RSTP system settings. The settings are used by all RSTP Bridge instances in the Switch or switch Stack. The Managed Switch support the following Spanning Tree pro...

Page 112 - “Compatibles”; RSTP Bridge Status; one

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 112 Compatible – Classis STP (802.1d) : Provides a single path between end stations, avoiding and eliminating loops. The Gigabit Ethernet Switch implement the Rapid Spanning Protocol as the default spanning tree protocol. While selec...

Page 113 - RSTP Port Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 113 4.7. 3 RSTP Port Configuration This page allows the user to inspect the current RSTP port configurations, and possibly change them as well. This page contain settings for aggregations and physical ports. The aggregation settings ...

Page 114 - forced Point2Point

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 114 path cost ports are chosen as forwarding ports in favor of higher path cost ports. Valid values are in the range 1 to 200000000. • Priority Controls the port priority. This can be used to control priority of ports having identica...

Page 116 - RSTP Port Status; The RSTP Port Status screen in; Port; The switch port number of the logical RSTP port.; Role

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 116 4.7. 4 RSTP Port Status This page displays the RSTP port status for port physical ports in the currently selected switch. The RSTP Port Status screen in Figure 4-7-10 appears. Figure 4-7-10 RSTP Port Status page screenshot The pa...

Page 117 - Bridge Status, if the port is RSTP enabled.; RSTP Port Statistics; The RSTP Port Statistics screen in

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 117 • State The current RSTP port state. The port state can be one of the following values: • Disabled • Blocking • Learning • Forwarding • Non-STP . • Bridge The RSTP Bridge instance (VLAN ID). This is also a link to the RSTP Detail...

Page 118 - Quality of Service; QoS Terminology; Classifier

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 118 4.8 Quality of Service 4.8.1 Understand QOS Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic. QoS enables you to assign various grades of network ser...

Page 119 - QCE Type

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 119 3. Create a QoS profile which associates a service level and a classifier. 4. Apply a QoS profile to a port(s). 4.8.2 QoS Control List Configuration This page lists the QCEs for a given QCL. Frames can be classified by 4 differ...

Page 124 - Frames that hit this QCE are set to match this specific QCL.; Port Members; port in a QCL member, click the radio button.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 124 Figure 4-8-6 Set up Policy Rules page screenshot The page includes the folling fileds: Object Description • QCL ID Frames that hit this QCE are set to match this specific QCL. • Port Members A row of radio buttons for each port i...

Page 125 - Audio and Video; Indicates the common servers that apply to the specific QCE .; Games; Indicates the common games that apply to the specific QCE.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 125 4.8.4.2 Set up Typical Network Application Rules Set up the specific QCL for different typical network application quality control. STEP-1 Set up the specific QCL for different typical network application quality control by sel...

Page 127 - Select the QCL ID to which this QCE applies.; ToS Precedence Class

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 127 4.8.4.3 Set up ToS Precedence Mapping Set up the traffic class mapping to the precedence part of ToS (3 bits) when receiving IPv4/IPv6 packets. The screen in Figure 4-8-10 appears. Figure 4-8-10 Set up ToS Precedence Mapping page...

Page 128 - VLAN Priority Class

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 128 4.8.4.4 Set up VLAN Tag Priority Mapping Set up the traffic class mapping to the User Priority value (3 bits) when receiving VLAN tagged packets. The screen in Figure 4-8-11 appears. Figure 4-8-11 Set up VLAN Tag Priority Mapping...

Page 130 - The logical port for the settings contained in the same row.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 130 4.8.6 Bandwidth Control Configure the switch port rate limit for Policers and Shapers on this page. The settings relate to the currently selected stack unit, as reflected by the page header. The screen Bandwidth Control in Figure...

Page 134 - IGMP Versions 1 and 2; IGMP Message Format; Type Meaning

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 134 IGMP Versions 1 and 2 Multicast groups allow members to join or leave at any time. IGMP provides the method for members and multicast routers to communicate when joining or leaving a multicast group. IGMP version 1 is defined in ...

Page 135 - message, and query messages that are specific to a given group.; Delaying Member; IGMP State Transitions; IGMP Querier –; ” and assumes the

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 135 message, and query messages that are specific to a given group. The states a computer will go through to join or to leave a multicast group are shown below: Non-Member Delaying Member Idle Member Leave Group Leave Group(Stop Time...

Page 140 - EAPOL; authentication methods, like; PEAP; Overview of MAC-Based Authentication; has nothing to do with the 802.1X standard.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 140 4.10 IEEE 802.1X Network Access Control Overview of 802.1X (Port-Based) Authentication In the 802.1X-world, the user is called the supplicant, the switch is the authenticator, and the RADIUS server is the authentication server. T...

Page 141 - Client

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 141 4.10.1 Understanding IEEE 802.1X Port-Based Authentication The IEEE 802.1X standard defines a client-server-based access control and authentication protocol that restricts unauthorized clients from connecting to a LAN through pub...

Page 142 - Authentication Initiation and Message Exchange; ” shows a message

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 142 z Switch (802.1X device) —controls the physical access to the network based on the authentication status of the client. The switch acts as an intermediary (proxy) between the client and the authentication server, requesting ident...

Page 143 - EAP message exchange; Ports in Authorized and Unauthorized States; unauthorized

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 143 Figure 4-10-2 EAP message exchange Ports in Authorized and Unauthorized States The switch port state determines whether or not the client is granted access to the network. The port starts in the unauthorized state. While in thi...

Page 147 - globally enabled; Port State

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 147 • Port The port number for which the configuration below applies. • Admin State Sets the authentication mode to one of the following options (only used when 802.1X or MAC-based authentication is globally enabled ): • Auto: Requir...

Page 148 - Restart; Schedules a reauthentication to whenever the

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 148 The stackswitch is "born" with a pool of state-machines, from which all ports draw whenever a new client is seen on the port. When a given port's maximum is reached (both authorized and unauthorized clients count), furthe...

Page 149 - the individual states.; Last Source

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 149 4.10.4 802.1X Port Status This page provides an overview of the current IEEE 802.1X port states for the selected switch. The 802.1X Port Status screen in Figure 4-10-5 appears. Figure 4-10-5 802.1X Status page screenshot The page...

Page 151 - EAPOL Counters

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 151 The selected port belongs to the currently selected stack unit as reflected by the table header. EAPOL Counters These counters are not available for MAC-based ports. Supplicant frame counter statistics. There are seven receive ...

Page 152 - RADIUS Counters

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 152 RADIUS Counters RADIUS Server frame counter statistics. For MAC-based ports there are two tables containing RADIUS counters. The left-most shows a summary of all RADIUS counters on this port. The right-most shows RADIUS counter...

Page 153 - Last Supplicant/Client Info; This table is only available for MAC-based ports; MAC Address; No clients attached; authenticated a client, it is unauthorized.; Last Authentication

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 153 MAC-based: Counts all the RADIUS packets sent from the switch towards the RADIUS server for a given port (left-most table) or client (right-most table). Possible retransmissions are not counted. Last Supplicant/Client Info For ...

Page 154 - Windows Platform RADIUS Server Configuration; you had set at the switch RADIUS server –; Local Authenticate; ”, the establishment of the user data needs to be

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 154 4.10.6 Windows Platform RADIUS Server Configuration 1. Setup the RADIUS server and assign the client IP address to the Managed switch. In this case, field in the default IP Address of the Managed Switch with 192.168.0.100. And al...

Page 155 - Windows Server RADIUS Server setting path; Active Directory Users and Computers; enter properties, and what to be noticed:

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 155 Figure 4-10-9 Windows Server RADIUS Server setting path 5. Enter ” Active Directory Users and Computers ”, create legal user data, the next, right-click a user what you created to enter properties, and what to be noticed: Figure ...

Page 156 - Configure Sample: EAP-MD5 Authentication

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 156 Set the Ports Authenticate Status to “ Force Authorized ” if the port is connected to the RADIUS server or the port is a uplink port that is connected to another switch. Or once the 802.1X stat to work, the switch might not be ab...

Page 157 - OK

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 157 Figure 4-10-12 7. Click “ OK ”. 8. When client has associated with the Managed Switch, a user authentication notice appears in system tray. Click on the notice to continue. Figure 4-10-13

Page 158 - ” to complete the validation process.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 158 9. Enter the user name, password and the logon domain that your account belongs. 10. Click “ OK ” to complete the validation process. Figure 4-10-14

Page 159 - Access Control Lists; Access Control List Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 159 4.11 Access Control Lists ACL is an acronym for Access Control List. It is the list table of ACEs, containing access control entries that specify individual users or groups permitted or denied to specific traffic objects, such as...

Page 160 - Policy

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 160 • Policy : The ACE will match ingress ports with a specific policy. • Port: The ACE will match a specific ingress port. • Frame Type Indicates the frame type of the ACE. Possible values are: • Any: The ACE will match any frame ty...

Page 163 - ARP Parameters; RARP

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 163 ARP Parameters The ARP parameters can be configured when Frame Type "ARP" is selected. Object Description • ARP/ RARP Specify the available ARP/RARP opcode (OP) flag for this ACE. • Any : No ARP/RARP OP flag is specifie...

Page 164 - IP; IP Parameters; IP Protocol Filter; Specify the IP protocol filter for this ACE.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 164 address field (THA) settings. 0 : RARP frames where THA is not equal to the SMAC address. 1 : RARP frames where THA is equal to the SMAC address. Any : Any value is allowed ("don't-care"). • IP/Ethernet Length Specify whe...

Page 166 - ICMP Parameters

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 166 address and destination IP mask in the DIP Address and DIP Mask fields that appear. • DIP Address When "Host" or "Network" is selected for the destination IP filter, you can enter a specific DIP address in dotted ...

Page 168 - Ethernet Type Parameters

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 168 Ethernet Type Parameters The Ethernet Type parameters can be configured when Frame Type "Ethernet Type" is selected. Object Description • EtherType Filter Specify the Ethernet type filter for this ACE. Any : No EtherTyp...

Page 170 - Frames that hit this ACE are set to match this specific policy.; port in a policy member, click the radio button.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 170 4.11.3.2 Set up Port Policies Group ports into several types according to different ACL policies. The settings relate to the currently selected stack unit, as reflected by the page header. The screen in Figure 4-11-4 appears. Fig...

Page 171 - ACL; Common Servers

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 171 4.11.3.3 Set up Typical Network Application Rules Set up the specific ACL for different typical network application access control. The screen in Figure 4-11-5 appears. STEP-1: Selecting the Network Application Type: Figure 4-1...

Page 175 - The screen in

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 175 Figure 4-11-9 4.11.3.5 Set up DoS Attack Detection Rules Set up the specific ACL for different typical network application access control. The screen in Figure 4-11-10 appears. Figure 4-11-10 Set up DoS Attack Detection Rules pag...

Page 176 - Death; ACE

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 176 packet of destination unreachable to the spoofed source address. Eventually leading it to be unreachable by other clients and the system will go down. • ICMP DoS - Ping of Death A malicious attacker sending a malformed ICMP reque...

Page 181 - Aging Configuration; Enables/disables the the automatic aging of dynamic entries; Aging Time

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 181 4.12 Address Table Switching of frames is based upon the DMAC address contained in the frame. The Managed Switch builds up a table that maps MAC addresses to switch ports for knowing which ports the frames should go to ( based up...

Page 183 - Type

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 183 4.12.3 MAC Address Table Status Dynamic MAC Table Entries in the MAC Table are shown on this page. The MAC Table contains up to 8192 entries, and is sorted first by VLAN ID, then by MAC address. Figure 4-12-3 MAC Address Table St...

Page 185 - MAC Table Learning

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 185 4.13 Port Security (To be Continued) Port security is a feature that allows you to configure a switch port with one or more device MAC addresses that are authorized to access the network through that port. When port security is e...

Page 188 - LLDP Parameters; frame is determined by the; Tx Interval; value. Valid values are restricted to 5 -

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 188 4.14.2 LLDP Configuration This page allows the user to inspect and configure the current LLDP port settings. The LLDP Configuration screen in Figure 4-14-1 appears. Figure 4-14-1 LLDP Configuration page screenshot LLDP Paramete...

Page 189 - Transmission Interval; Tx Reinit

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 189 This attribute must comply with the following rule: (Transmission Interval * Hold Time Multiplier) ≤ 65536, and Transmission Interval >= (4 * Delay Interval) • Tx Hold Each LLDP frame contains information about how long the in...

Page 192 - LLDP Statistics; LLDP Statistics page screenshot; Global Counters; the time elapsed since last change was detected.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 192 4.14. 4 LLDP Statistics This page provides an overview of all LLDP traffic. Two types of counters are shown. Global counters are counters that refer to the whole stack, switch, while local counters refers to counters for the curr...

Page 193 - Local Counters

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 193 • Total Neighbors Entries Dropped Shows the number of LLDP frames dropped due to that the entry table was full. • Total Neighbors Entries Aged Out Shows the number of entries deleted due to Time-To-Live expiring. Local Counters...

Page 194 - Network Diagnastics; This page is used for running the Cable Diagnostics.; The port where you are requesting Cable Diagnostics.; Cable Status

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 194 4.15 Network Diagnastics 4.15.1 Cable Diagnostics This page is used for running the Cable Diagnostics. Press to run the diagnostics. This will take approximately 5 seconds. If all ports are selected, this can take approximately 1...

Page 198 - Assigning and Swapping Switch IDs; so that it is easier for the user to remember the ID of each switch.; Removing a Switch From the Stack

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 198 4.16.1 Stack This section provides information for understand stacking architecture, include the below items: Switch IDs • Assigning and Swapping Switch IDs • Removing a Switch From the Stack • Replacing a Switch • General Swit...

Page 199 - General Switch ID Assignment Rules; Deleting a switch will remove any configuration pertaining to it.; master; master for the longest period of time will become master.; smallest master priority; The switch with the; smallest MAC address; uninterrupted management and monitoring.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 199 "Save". 5. The new hardware has now taken over the configuration of the failing hardware. General Switch ID Assignment Rules When assigning Switch IDs to the devices in the stack, you must note the following: 1. Switche...

Page 200 - Remove or Replace a switch from the stack; shortest path forwarding as below:; Automatic Loop Prevention; True Ring Topology

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 200 Figure 4-16-4 Remove or Replace a switch from the stack 4.16.1.4 Shortest Path Forwarding The SGSW Swtich supports shortest path forwarding technology to optimal data flow across the stack. The advantage of shortest path forwardi...

Page 202 - Stack Topology; Stack List

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 202 4.16.3 Stack Information This page provides an overview of the stack topology, as detected by SPROUT. Stack Topology The Stack Topology screen in Figure 4-16-7 appears. Figure 4-16-7 Stack Information page screenshot - Stack To...

Page 203 - Master Forwarding Table

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 203 Figure 4-16-8 Stack Information page screenshot - Stack List The page includes the following fields: Object Description • Delete Deletes this switch from the stack configuration. • Stack Member The MAC address of the switch. • Sw...

Page 204 - Stack Information page screenshot - Master Forwarding Table; page.The port states are illustrated as follows:

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 204 Figure 4-16-9 Stack Information page screenshot - Master Forwarding Table 4.16.4 Stack Port State Ovewview This page provides an overview of the current switch port states. Clicking on the image of a port opens the Port Statistic...

Page 207 - arp –d

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 207 Reflash the web browser, the switch with MAC address “00-30-4f-24-04-76” become the stack master now. Figure 4-16-14 The result after master election Step 6: After the Stack Master and Members have been configured, any switch i...

Page 208 - COMMAND LINE INTERFACE; Accessing the CLI; This chapter describes how to use the Command Line Interface (CLI).; Logon to the Console; WGSW / SGSW Managed Switch Console Login screen

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 208 5. COMMAND LINE INTERFACE 5.1 Accessing the CLI When accessing the management interface for the switch over a direct connection to the server’s console port, or via a Telnet connection, the switch can be managed by entering comma...

Page 209 - Only accept command in lowercase letter under console interface.; Show the current IP address; As show in; Configure IP address; ” prompt, enter the following command and press

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 209 1. For security reason, please change and memorize the new password after this first setup. 2. Only accept command in lowercase letter under console interface. Configure IP address The WGSW / SGSW Managed Switch is shipped with d...

Page 210 - help; ” anytime in

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 210 Switch/> ip setup 192.168.1.100 255.255.255.0 192.168.1.1 The previous command would apply the follow settings for the Switch. IP: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 Figure 5-3 Set IP address screen ...

Page 211 - login when using telnet, please use; “admin”

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 211 5.2 Telnet login The Managed Switch also supports telnet for remote management. The switch asks for user name and password for remote login when using telnet, please use “admin” for password.

Page 212 - Command Line Mode; System Command; System Configuration; Show system configuration.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 212 6. Command Line Mode The CLI groups all the commands in appropriate modes according to the nature of the command. A sample of the CLI command modes are described below. Each of the command modes supports specific software command...

Page 213 - all

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 213 all : Show all switch configuration, default: Show system configuration <port_list> : Port list or 'all', default: All ports Example: To display system information: Switch/>system configuration System Name : SGSW-24040 S...

Page 214 - System Name; Set or show the system name.; System Prompt; Set the CLI prompt string.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 214 Parameters: keep_ip : Keep IP configuration, default: Restore full configuration Example: To restore default value but not reset IP address: Switch/>system restore default keep_ip System Name Description: Set or show the syste...

Page 215 - System Password; Set or show the system password.; System SNTP; Set or show the SNTP Time server address.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 215 Parameters: <prompt> : CLI prompt string Default Setting: SWITCH Example: To change CLI title: Switch/>system prompt SGSW-24040 SGSW-24040/> System Password Description: Set or show the system password. Syntax: System...

Page 216 - System Timezone; Set or show the system timezone offset.; System Firmware Load; Load new firmware from TFTP server.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 216 Parameters: <ip_addr> : IP address (a.b.c.d), default: Show IP address Default Setting: 0.0.0.0 Example: Set SNTP server: SWITCH/>system sntp 220.130.158.52 System Timezone Description: Set or show the system timezone of...

Page 217 - : Firmware file name

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 217 <ip_server> : TFTP server IP address (a.b.c.d) <file_name> : Firmware file name

Page 218 - enable

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 218 IP Configuration Description: Show IP configuration. Syntax: IP Configuration Example: Show IP configuration: Switch/>ip configuration DHCP Client: Disabled IP Address : 192.168.100.105 IP Mask : 255.255.255.0 IP Router : 192....

Page 219 - IP Setup; Set or show the IP setup.; IP Ping

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 219 IP Setup Description: Set or show the IP setup. Syntax: IP Setup [<ip_addr>] [<ip_mask>] [<ip_router>] [<vid>] Parameters: <ip_addr> : IP address (a.b.c.d), default: Show IP address <ip_mask> :...

Page 221 - Port Management Command

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 221 6.2 Port Management Command Port Configuration Description: Show port configuration. Syntax: Port Configuration [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports Example: Display port1~4 s...

Page 222 - Port Mode; auto; Port Flow Control

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 222 Default Setting: Enable Example: Disable port1 SWITCH/>port state 1 disable Port Mode Description: Set or show the port speed and duplex mode. Syntax: Port Mode [<port_list>] [10hdx|10fdx|100hdx|100fdx|1000fdx|auto] Para...

Page 223 - : Enable flow control; disable; : Disable flow control; Port Maximum Frame; Set or show the port maximum frame size.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 223 Syntax: Port Flow Control [<port_list>] [enable|disable] Parameters: <port_list> : Port list or 'all', default: All ports enable : Enable flow control disable : Disable flow control (default: Show flow control mode) D...

Page 226 - Port Numbers; Show port numbering.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 226 Port Numbers Description: Show port numbering. Syntax: Port Numbers

Page 227 - Mirror Configuration; Show mirror configuration.; Mirror Port; Set or show the mirror port.; Mirror SID; Set or show the mirror switch ID.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 227 Mirror Configuration Description: Show mirror configuration. Syntax: Mirror Configuration [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports Mirror Port Description: Set or show the mirror ...

Page 228 - Mirror Mode

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 228 Default Setting: 1 Example: Set mirror SID 2 for switch SWITCH/>mirror sid 2 Mirror Mode Description: Set or show the mirror mode. Syntax: Mirror Mode [<port_list>] [enable|disable|rx|tx] Parameters: <port_list> : ...

Page 229 - Link Aggregation Command; Aggregation Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 229 6.3 Link Aggregation Command Aggregation Configuration Description: Show link aggregation configuration. Syntax: Aggr Configuration Example: SWITCH/>aggr configuration Aggregation Mode: SMAC : Enabled DMAC : Disabled IP : Enab...

Page 231 - Aggregation Mode

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 231 Aggregation Mode Description: Set or show the link aggregation traffic distribution mode. Syntax: Aggr Mode [smac|dmac|ip|port] [enable|disable] Parameters: smac : Source MAC address dmac : Destination MAC address ip : Source and...

Page 232 - LACP Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 232 LACP Configuration Description: Show LACP configuration. Syntax: LACP Configuration [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports Example: Show LACP configuration SWITCH/>lacp confi...

Page 233 - LACP Mode; LACP Key

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 233 21 Disabled Auto Active 22 Disabled Auto Active 23 Disabled Auto Active 24 Disabled Auto Active LACP Mode Description: Set or show LACP mode. Syntax: LACP Mode [<port_list>] [enable|disable] Parameters: <port_list> : ...

Page 235 - LACP Statistics

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 235 Parameters: <port_list> : Port list or 'all', default: All ports Example: Show LACP status of port1~4 SWITCH/>lacp status 1-4 Port Mode Key Aggr ID Partner System ID Partner Port ------ ------------ ----- ------- -------...

Page 237 - VLAN Configuration Command; VLAN Configuration; portbased

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 237 6.4 VLAN Configuration Command VLAN Configuration Description: Show VLAN configuration. Syntax: VLAN Configuration [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports Example: Show VLAN stat...

Page 239 - VLAN Ingress Filter; VLAN Link Type

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 239 (default: Show accepted frame types) Default Setting: All Example: Set port20 that allow tagged frames only SWITCH/>vlan frametype 20 tagged VLAN Ingress Filter Description: Set or show the port VLAN ingress filter. Syntax: VL...

Page 240 - VLAN Ethernet Type; Set or show out layer VLAN tag ether type in Q-in-Q VLAN mode.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 240 Parameters: <port_list> : Port list or 'all', default: All ports untagged : VLAN Link Type Tagged tagged : VLAN Link Type Untagged Default Setting: Un-tagged Example: Enable tagged frame for port2 SWITCH/>vlan linktype 2...

Page 241 - : Set out layer VLAN tag ether type : 802.1Q; VLAN Add; Add or modify VLAN entry.; VLAN Delete

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 241 dot1q : Set out layer VLAN tag ether type : 802.1Q Default Setting: N/A Example: SWITCH/>vlan ethtype 10 man VLAN Add Description: Add or modify VLAN entry. Syntax: VLAN Add <vid> [<port_list>] Parameters: <vid&...

Page 242 - VLAN Lookup; Show VLAN status

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 242 <vid> : VLAN ID (1-4095) Example: Delete port17 to port24 in VLAN10 SWITCH/>vlan delete 10 17-24 VLAN Lookup Description: Lookup VLAN entry. Syntax: VLAN Lookup [<vid>] Parameters: <vid> : VLAN ID (1-4095), d...

Page 244 - Spanning Tree Protocol Command; RSTP Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 244 6.5 Spanning Tree Protocol Command RSTP Configuration Description: Show RSTP configuration. Syntax: RSTP Configuration [<port_list>] Parameters: <port_list> : Port list or 'all'. Port zero means aggregations. Default ...

Page 245 - Set RSTP system priority value in 4096; RSTP Age; Set or show the RSTP maximum age.; RSTP Delay; Set or show the RSTP forward delay.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 245 Default Setting: 32768 Example: Set RSTP system priority value in 4096 SWITCH/>rstp sysprio 4096 RSTP Age Description: Set or show the RSTP maximum age. Syntax: RSTP Age [<max_age>] Parameters: <max_age>: RSTP maxi...

Page 246 - RSTP Version; compatible; RSTP Mode

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 246 15 Example: Set RSTP forward delay value in 25 SWITCH/>rstp delay 25 RSTP Version Description: Set or show the RSTP protocol version. Syntax: RSTP Version [compatible|normal] Parameters: compatible : Compatible with STP normal...

Page 248 - Set RSTP priority value in 16 for port1; RSTP Edge; Set or show the RSTP edge parameter.; Enable; RSTP P2P; Set or show the RSTP point2point parameter.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 248 <priority> : RSTP priority (0/16/32/48/.../224/240) Default Setting: 128 Example: Set RSTP priority value in 16 for port1 SWITCH/>rstp priority 1 16 RSTP Edge Description: Set or show the RSTP edge parameter. Syntax: RST...

Page 249 - RSTP Status

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 249 Parameters: <port_list> : Port list or 'all', default: All ports enable : Enable RSTP point2point disable : Disable RSTP point2point auto : Automatic RSTP point2point detection Default Setting: Auto Example: Enable RSTP P2P...

Page 250 - RSTP Statistics; Show RSTP statistics.; RSTP mCheck

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 250 RSTP Statistics Description: Show RSTP statistics. Syntax: RSTP Statistics [<port_list>] Parameters: <port_list>: Port list or 'all', default: All ports RSTP mCheck Description: Set the RSTP mCheck (Migration Check) v...

Page 251 - Multicast Configuration Command; IGMP Configuration

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 251 6.6 Multicast Configuration Command IGMP Configuration Description: Show IGMP snooping configuration. Syntax: IGMP Configuration [<port_list>] Parameters: <port_list>: Port list or 'all', default: All ports Default Se...

Page 252 - IGMP State

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 252 Enable IGMP mode SWITCH/>igmp mode enable IGMP State Description: Set or show the IGMP snooping state for VLAN. Syntax: IGMP State [<vid>] [enable|disable] Parameters: <vid>: VLAN ID (1-4095), default: Show all VLA...

Page 253 - IGMP Querier; IGMP Fast Leave

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 253 disable : Disable IGMP snooping (default: Show IGMP snooping mode) Default Setting: Enable Example: Disable VID 1 SWITCH/>igmp state 1 disable IGMP Querier Description: Set or show the IGMP snooping querier mode for VLAN. Synt...

Page 254 - IGMP Router

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 254 IGMP Fastleave [<port_list>] [enable|disable] Parameters: <port_list> : Port list or 'all', default: All ports enable : Enable IGMP fast leave disable : Disable IGMP fast leave (default: Show IGMP fast leave mode) Def...

Page 255 - IGMP Flooding; Set or show the IGMP snooping unregistered flood operation.; : Enable IGMP flooding; : Disable IGMP flooding; IGMP Groups

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 255 IGMP Flooding Description: Set or show the IGMP snooping unregistered flood operation. Syntax: IGMP Flooding [enable|disable] Parameters: enable : Enable IGMP flooding disable : Disable IGMP flooding (default: Show IGMP flood mod...

Page 257 - Quality of Service Command; QoS Configuration; Show QoS Configuration.; QoS Classes; Set or show the number of traffic classes.; QoS Default; Set or show the default port priority.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 257 6.7 Quality of Service Command QoS Configuration Description: Show QoS Configuration. Syntax: QoS Configuration [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports QoS Classes Description: S...

Page 258 - QoS Tag Priority; Set or show the port VLAN tag priority.; QoS QCL Port; Set or show the port QCL ID.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 258 Parameters: <port_list> : Port list or 'all', default: All ports <class> : Traffic class low/normal/medium/high or 1/2/3/4 Default Setting: Low Example: Set high priority for port5 SWITCH/>qos default 5 high QoS Ta...

Page 259 - Set QCL ID5 for port10; QoS QCL Add; QCE ID is not specified, the QCE will be placed last in the list.; etype; : Ethernet Type keyword

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 259 QoS QCL Port [<port_list>] [<qcl_id>] Parameters: <port_list> : Port list or 'all', default: All ports <qcl_id> : QCL ID Default Setting: 1 Example: Set QCL ID5 for port10 SWITCH/>qos qcl port 10 5 QoS ...

Page 260 - QoS QCL Delete

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 260 <etype> : Ethernet Type vid : VLAN ID keyword <vid> : VLAN ID (1-4095) port : UDP/TCP port keyword <udp_tcp_port> : Source or destination UDP/TCP port (0-65535) dscp : IP DSCP keyword <dscp> : IP DSCP (0-6...

Page 261 - QoS Mode; Set or show the port egress scheduler mode.; strict; Strict; QoS Weight; Set or show the port egress scheduler weight.; QoS Rate Limiter; Set or show the port rate limiter.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 261 QoS Mode Description: Set or show the port egress scheduler mode. Syntax: QoS Mode [<port_list>] [strict|weighted] Parameters: <port_list> : Port list or 'all', default: All ports strict : Strict mode weighted : Weigh...

Page 262 - : Enable rate limiter; : Disable rate limiter; QoS Shaper; Set or show the port shaper.; : Enable shaper; : Disable shaper

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 262 Syntax: QoS Rate Limiter [<port_list>] [enable|disable] [<bit_rate>] Parameters: <port_list> : Port list or 'all', default: All ports enable : Enable rate limiter disable : Disable rate limiter (default: Show ra...

Page 263 - QoS Unicast; QoS Multicast

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 263 SWITCH/>qos shaper 9-16 enable 1000 QoS Unicast Description: Set or show the unicast storm rate limiter. Syntax: QoS Storm Unicast [enable|disable] [<packet_rate>] Parameters: enable : Enable unicast storm control disabl...

Page 264 - Enable multicast storm rate limiter in 1kpps; QoS Broadcast; Set or show the multicast storm rate limiter.; : Enable broadcast storm control; : Disable broadcast storm control

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 264 Example: Enable multicast storm rate limiter in 1kpps SWITCH/>qos storm multicast enable 1k QoS Broadcast Description: Set or show the multicast storm rate limiter. Syntax: QoS Storm Broadcast [enable|disable] [<packet_rate...

Page 266 - Dot1x Status; macbased; Dot1x Server

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 266 disable : Disable 802.1X (default: Show 802.1X mode) Default Setting: Disable Example: Enable IEEE802.1x founction for port1 SWITCH/>dot1x mode enable Dot1x Status Description: Set or show the 802.1X port state. Syntax: Dot1x ...

Page 267 - Dot1x Secret; Set or show the secret shared with the RADIUS server.; Dot1x Authenticate

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 267 Syntax: Dot1x Server [<ip_addr>] Parameters: ip_addr : RADIUS server IP address (a.b.c.d) (default: Show IP address) Default Setting: 0.0.0.0 Example: Set RADIUS server IP address for switch. RADIUS server IP address is 192...

Page 268 - now; Dot1x Re-authentication; Dot1x Period

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 268 Refresh (restart) 802.1X authentication process. Syntax: Dot1x Authenticate [<port_list>] [now] Parameters: <port_list> : Port list or 'all', default: All ports now : Force reauthentication immediately Dot1x Re-authen...

Page 269 - Set period re-authentication time in 3000 seconds; Dot1x Timeout; Set or show the time between EAPOL retransmissions.; Dot1x Statistics

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 269 <reauth_period> : Period between reauthentications (1-3600 seconds) (default: Show reauthentication period) Default Setting: 3600 Example: Set period re-authentication time in 3000 seconds SWITCH/>dot1x period 3000 Dot1x...

Page 270 - clear; : Clear statistics; eapol; : Show EAPOL statistics; radius; : Show RADIUS statistics; Dot1x Clients; : Allow all new clients; Dot1x Agetime

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 270 Parameters: <port_list> : Port list or 'all', default: All ports clear : Clear statistics eapol : Show EAPOL statistics radius : Show RADIUS statistics (default: Show all statistics) Dot1x Clients Description: Set or show t...

Page 271 - Set age time in 100 seconds; Dot1x Holdtime; Set hold time in 100 seconds

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 271 300 Example: Set age time in 100 seconds SWITCH/>dot1x agetime 100 Dot1x Holdtime Description: Time in seconds before a MAC-address that failed authentication gets a new authentication chance. Syntax: Dot1x Holdtime [<hold_...

Page 272 - Access Control List Command; ACL Configuration; Show ACL Configuration.; ACL Action; Set or show the ACL port default action.; permit; : Deny forwarding

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 272 6.9 Access Control List Command ACL Configuration Description: Show ACL Configuration. Syntax: ACL Configuration [<port_list>] Parameters: <port_list>: Port list or 'all', default: All ports Default Setting: 300 Examp...

Page 273 - Rate Limiter: Disable; ACL Policy; Set or show the ACL port policy.; ACL Rate; Set or show the ACL rate limiter.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 273 Rate Limiter: Disable Port Copy: Disable Loading: Disable Shut down: Disable Example: ???? SWITCH/>acl action 17-24 deny 1 24 log shut ACL Policy Description: Set or show the ACL port policy. Syntax: ACL Policy [<port_list&...

Page 274 - ACL Add; switch

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 274 <rate_limiter_list> : Rate limiter list (1-15), default: All rate limiters <packet_rate> : Rate in pps (1, 2, 4, ..., 512, 1k, 2k, 4k, ..., 1024k) Default Setting: 1 Example: ??? SWITCH/>acl rate 15 1024k ACL Add D...

Page 275 - ACL Delete

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 275 <smac> : Source MAC address (xx-xx-xx-xx-xx-xx) or 'any' <dmac> : Destination MAC address (xx-xx-xx-xx-xx-xx) or 'any' arp : ARP keyword <sip> : Source IP address (a.b.c.d/n) or 'any' <dip> : Destination I...

Page 276 - Clear all ACL counters.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 276 ACL Lookup Description: Show ACE, default: All ACEs. Syntax: ACL Lookup [<ace_id>] Parameters: <ace_id> : ACE ID (1-1024) ACL Lookup Description: Clear all ACL counters. Syntax: ACL Clear

Page 277 - MAC Address Table Command; MAC Configuration; Show MAC address table configuration.; Mac Add; Add MAC address table entry.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 277 6.10 MAC Address Table Command MAC Configuration Description: Show MAC address table configuration. Syntax: MAC Configuration [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports Example: Sho...

Page 278 - MAC Delete; Delete MAC address entry.; MAC Lookup; Lookup MAC address entry.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 278 Example: Add Mac address 00-30-4F-01-01-02 in port1 and vid1 SWITCH/>mac add 00-30-4f-01-01-02 1 1 MAC Delete Description: Delete MAC address entry. Syntax: MAC Delete <mac_addr> [<vid>] Parameters: <mac_addr>...

Page 280 - MAC Dump; Show sorted list of MAC address entries.; MAC Statistics; Show MAC address table statistics.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 280 SWITCH/>mac learning 1 secure MAC Dump Description: Show sorted list of MAC address entries. Syntax: MAC Dump [<mac_max>] [<mac_addr>] [<vid>] Parameters: <mac_max> : Maximum number of MAC addresses 1-8...

Page 281 - MAC Flash; Flush all learned entries.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 281 MAC Flash Description: Flush all learned entries. Syntax: MAC Flush

Page 283 - LLDP Optional TLV; default; LLDP Interval

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 283 LLDP Optional TLV Description: Show / Set LLDP Optional TLVs. Syntax: LLDP Optional_TLV [<port_list>] [port_descr|sys_name|sys_descr|sys_capa|mgmt_addr] [enable|disable] Parameters: <port_list> : Port list or 'all', d...

Page 284 - Set transmission interval in 10; LLDP Hold; Set or show LLDP Tx hold value.; LLDP Delay; Set or show LLDP Tx delay.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 284 Parameters: <interval> : LLDP transmission interval (5-32768) Default Setting: 30 Example: Set transmission interval in 10 SWITCH/>lldp interval 10 LLDP Hold Description: Set or show LLDP Tx hold value. Syntax: LLDP Hold...

Page 285 - Set LLDP delay value in 1; LLDP Reinit; Set or show LLDP reinit delay.; LLDP Information; Show LLDP neighbor device information.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 285 <delay> : LLDP transmission delay (1-8192) Default Setting: 2 Example: Set LLDP delay value in 1 SWITCH/>lldp delay 1 LLDP Reinit Description: Set or show LLDP reinit delay. Syntax: LLDP Reinit [<reinit>] Parameter...

Page 286 - Show LLDP Statistics.; : Clear LLDP statistics

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 286 LLDP Statistics Description: Show LLDP Statistics. Syntax: LLDP Statistics [<port_list>] [clear] Parameters: <port_list> : Port list or 'all', default: All ports clear : Clear LLDP statistics

Page 287 - Stack Management Command; Show the list of switches in stack.; detailed; : Show detailed information; Set the master election priority.; Stack Master Reelect

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 287 6.12 Stack Management Command Stack List Description: Show the list of switches in stack. Syntax: Stack List [detailed|productinfo] Parameters: detailed : Show detailed information Stack List Description: Set the master election ...

Page 288 - Stack Select; Set or show the selected switch ID.; Stack SID Swap; Swap SID values used to identify two switches.; Stack SID Delect; Delete SID assignment and associated configuration.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 288 Stack Select Description: Set or show the selected switch ID. Syntax: Stack Select [<sid>|all] Parameters: <sid> : Switch ID (1-16), default: Show SID Example: Select switch2 to management switch2 SWITCH/>stack sel...

Page 289 - Stack SID Asign; Assign SID and associated configuration to switch.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 289 Stack SID Delete <sid> Parameters: <sid> : Switch ID (1-16) Stack SID Asign Description: Assign SID and associated configuration to switch. SID must be unassigned, switch must be present and switch must not already be...

Page 291 - If attached device is:

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 291 7.5 Auto-Negotiation The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Po...

Page 294 - Stacking not functioning; Check that modules are installed correctly; While IP Address be changed or forgotten admin password; at the front panel about

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 294 ■ Stacking not functioning Solution: 1. Check that modules are installed correctly 2. PLANET CB-STX50 or CB-STX200 cables not installed correctly (LEDs on front panel STX1 or STX2 do not light) 3. Check that the cables are insert...

Page 295 - APPENDEX A; Contact; is beyond the scope of this standard.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 295 APPENDEX A A.1 Switch's RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- Implicit impleme...

Page 297 - APPENDEX B : GLOSSARY; Port Aggregation, Link Aggregation; ARP

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 297 APPENDEX B : GLOSSARY A ACE ACE is an acronym for A ccess C ontrol E ntry. It describes access permission associated with a particular ACE ID. There are three ACE frame types (Ethernet Type, ARP, and IPv4) and two ACE actions (pe...

Page 303 - PING; ping; Policer

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 303 optional TLVs. If an optional TLVs is disabled the corresponding information is not included in the LLDP frame. P PING ping is a program that sends a series of packets over a network or the Internet to a specific computer in orde...

Page 305 - ROU

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 305 which is the underlying protocol used in Microsoft Windows networking. Samba can be installed on a variety of operating system platforms, including Linux, most common Unix platforms, OpenVMS, and IBM OS/2. Samba can also register...

Page 308 - the provider port with a double VLAN tag.

User’s Manual of WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R 308 forwarded to the provider port with a single VLAN tag. Tagged frames received on a subscriber port are forwarded to the provider port with a double VLAN tag. VLAN ID VLAN ID is a 12-bit field specifying the VLAN to which the fram...