Planet SW-801 - Manuals - manualsarea.com

Page 3 - CE Mark Warning; Revision

- 2 - user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harm- ful interference, in which case the user will be required to correct the in- terference at his own expense. CE Mark Warning In a domestic environment...

Page 4 - Table of Contents

Table of Contents CHAPTER 1 INTRODUCTION ................................................... 1 F AST E THERNET T ECHNOLOGY .................................................................. 1 S WITCHING T ECHNOLOGY ......................................................................... 1 F EATURES...

Page 5 - About This Manual; Purpose; Switch

About This Manual Congratulations on your purchasing of SW-501/SW-801, 5/8-port 10/100Mbps Fast Ethernet Switch. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible desktop package. Purpose This manual discusses how to install your SW-501/SW-801...

Page 7 - Chapter 1 Introduction; Fast Ethernet Technology; Switching Technology

- 1 - Chapter 1 Introduction This chapter describes the features of the Switch and some background information about Ethernet/Fast Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the ne...

Page 8 - Features

- 2 - segments. The switch, without interfering with any other segments, auto- matically forwards traffic that needs to go from one segment to another. By doing this the total network capacity is multiplied, while still maintaining the same network cabling and adapter cards. For Fast Ethernet networ...

Page 10 - Chapter 2 Unpacking and Setup; Unpacking

- 4 - Chapter 2 Unpacking and Setup This chapter provides unpacking and setup information for the Switches. Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: One 5/8-port 10/100Mbps Ethernet Switch One external power ...

Page 11 - Chapter 3 Identifying External Components; Front Panel; Rear Panel

- 5 - Chapter 3 Identifying External Components This section identifies all the major external components of the hub. Both the front and rear panels are shown followed by a description of each panel feature. The indicator panel is described in detail in the next chapter. Front Panel The figure below...

Page 12 - LED Indication

- 6 - DC Power Jack: Power is supplied through an external AC power adapter. Check the printing on the adapter for information about the AC power in- put voltage. Since the switch does not include a power switch, plugging its power adapter into a power outlet will immediately power it on. Numbered M...

Page 13 - Chapter 4 Connecting The Switch; PC to Switch; Hub to Switch

- 7 - Chapter 4 Connecting The Switch This chapter describes how to connect the Switch to your Fast Ethernet network. PC to Switch A PC can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable. The PC (equipped with a RJ-45 10/100Mbps phone jack) should be connected to a...

Page 14 - Port Speed & Duplex Mode; If the attached device does not support

- 8 - Switch to switches (other devices) The Switch can be connected to another switch or other devices (routers, bridges, etc.) via a two-pair Category 3, 4, 5 UTP/STP straight or crossover cable. When using straight or crossover cable, this is done from the any (MDI/MDIX) port of the Switch to any...

Page 15 - Chapter 5 TECHNICAL SPECIFICATIONS

- 9 - Chapter 5 TECHNICAL SPECIFICATIONS Standards IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100 Base-TX Fast Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full duplex) Fast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex) Topology Star Network Cables 10BA...

Page 16 - Appendix A RJ-45 PIN Specification

- 10 - Appendix A RJ-45 PIN Specification When connecting your 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/MDI-X detection. That means you can directly connect the Switch to any Ethernet device...

Page 18 - Appendix B SWITCH OPERATION; Address Table; Learning

- 12 - Appendix B SWITCH OPERATION Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address infor- mation of some node in network, including MAC address, port no, etc. The information comes from the learning p...