Paslode 902400 - Manuals

4 Safety Instructions DANGER WARNING WARNING Do not expose the tool to temperatures in excess of 120° F (49° C). Fuel and/or the battery may burst, releasing flammable gas. WARNING WARNING The following safety instructions have been included in this booklet to provide you with basic information nece...

5 Safety Instructions WARNING 7. N E V E R O P E R AT E T H E T O O L W I T H T H E WORK CONTACTING ELEMENT REMOVED OR DISABLED. This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating until it is completely against the work surface. NEVER oper...

6 Safety Instructions 12. NEVER DRIVE FASTENERS INTO AREAS WITH CONCEALED HAZARDS. Always check the area behind the work surface for electrical wiring, gas pipes, water pipes, sewer drains or other potential hazards. 13. ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED FOOTING WHEN ON LADDERS, PLATFORMS OR O...

7 Warning CHEMICAL/EXPLOSIONHAZARDRead ALL instructions be-fore charging or using bat-tery. Failure to follow ALL instructions may result in fire, severe burns, or re-lease of toxic materials. Battery and Charging System Charging Instructions 1. 2. Remove the battery from tool or case and insert ter...

8 Battery and Charging System Inserting Battery 1. h s i n i F s s e l d r o C e h t o t n i ,t s r fi s t c a t n o c , y r e tt a b e h t d a o LNailer. 2. Push battery fully forward into its locked Ready position. The battery indicator light will light. 3. NOTE: If battery is left in tool for an ...

9 DANGER E X P L O S I O N / F I R E HAZARD WARNING Sunlight can raise the inside temperature of an unventilated car or van to above 140°F (60°C). Never puncture or attempt to open the fuel cartridge; it is non-refillable. Never incinerate, reclaim or recycle the fuel cartridge. Never smoke while in...

10 Fuel Cartridge NOTE: Paslode Cordless fuel cartridges are marked with a “Best Use Before” date on the bottom of the can. For maximum performance use fuel before the “Best Use Before” date. Paslode Cordless Fuel Cartridge Disposal Guidelines Paslode the industry leader in cordless technology provi...

11 Inserting Fuel Cartridge ➔ 1. PRESS UP ➔ 1. Close over 2. PULL OUT ➔ 2. PRESS DOWN ➔ Fuel Ca rtridge B. Lift the fuel cartridge adaptor and insert the fuelcartridge into the tool. C. Release the adaptor so it is centered on the fuelcartridge. A. When loading a fuel cartridge, lift the tool off of...

12 Paslode Cordless 16 ga. Angled y r d n i , s r o o d t u o r e li a N h s i n i F s s e l d r o C e h t e s Uweather, when the nailer, fuel cartridge and battery are between 20°F (-7°C) and 120°F (49°C). HOT WEATHER OPERATION The Cordless Finish Nailer requires cooling of the motor assembly to op...

13 Paslode Cordless 16 ga. Angled Depth of Drive Adjustment Remove the battery before adjusting the depth of drive. The depth of drive adjustment is done by turning the adjustment wheel as shown by the arrows on the side of the tool. PRESS WORK –CONTACTINGELEMENT AGAINST THE WORK SURFACE. Fan motor ...

14 Fasteners and Applications Applications The Paslode Cordless 16 ga. Angled Finish Nailer is suited for a variety of applications. These include securing door and window casings; attaching baseboards where walls meet floors; attaching moldings where walls meet ceilings; securing paneling; securing...

15 Restrict Field Service to the Following RECHARGING THE BATTERY CHECKING THE FUEL CARTRIDGE REPLACING THE FUEL CARTRIDGE CLEANING/REPLACING THE AIR FILTER CLEARING A JAM CLEANING THE TOOL (See cleaning manual) Attempts to go beyond these procedures could result in serious personal injury or damage...

16 Servicing Air Filter Open the grille by pressing slightly above the adapter and pivoting the cover open. The air filter simply lifts out. n a e l c d n a k c e h C . t s u d y n a e v o m e r o t Y L T N E G r e tl fi e h t p a Tthe air filter every two days. Soap and water restores the filter to...

17 Battery does not appear to accept charge when battery is plugged into the charger. Charger gets hot, makes excessively loud noise, or smokes during charging cycle. Charger cord or wall plug gets hot. Inoperative indicator lights on charger, or defective charger. Battery damaged or cycle life exha...

18 Tool operates properly, but fasteners do not drive fully. Tool operates properly, but fasteners are sometimes over-driven, and sometimes under-driven. Tool operates, but no fastener is driven. Tool operates erratically or appears to be losing power - tool indicator light is green. Work-contacting...