Paradyne SMD2000-24T - Manuals

Paradyne SMD2000-24T – Manual in PDF format online.

Manuals:

Manual

Manual Paradyne SMD2000-24T

Summary

Page 2 - Software and Firmware License Agreement

2 Software and Firmware License Agreement The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or firmware (individually or collectively the “Software”) incorporated into the Paradyne product (the “Product”) purchased by you and any derivatives obtained...

Page 3 - Product Documentation Online

3 b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so...

Page 4 - Unpacking and Inspecting the Equipment; HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES; Site Selection Criteria

4 Unpacking and Inspecting the Equipment HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control p...

Page 5 - Installing Uplink Interface Modules (Optional); Procedure; Remove the Chassis Cover.; Side

5 Installing Uplink Interface Modules (Optional) An SMD2000-24T does not require installation of an Uplink Interface Module (UIM) for operational purposes. A UIM offers additional upstream network ports to supplement the two T1 uplink ports already provided. You may wish to install a UIM if your net...

Page 6 - Align and secure the PCBs.; Standoffs

6 2. Mount the UIM on the SMD2000-24T Printed Circuit Board (PCB). A UIM may be installed in either Port 1 or Port 2, or both for redundancy purposes. Using a Phillips screwdriver, remove the flathead screws from both sides of the chosen port on the chassis faceplate. Remove the slot cover. C AUTION...

Page 7 - Secure the faceplate.; Replace the chassis cover.; Tabletop Installation

7 5. Secure the faceplate. Using a Phillips screwdriver, secure the UIM faceplate to the SMD2000-24T faceplate with the two flathead screws included in your UIM packaging. 6. Replace the chassis cover. Replace the chassis cover and secure with the original eight flathead screws as depicted in Step 1...

Page 8 - Rack Installation

8 Rack Installation Procedure To install the SMD2000-24T in a rack: 1. Using a Phillips screwdriver, attach the two provided rack mount brackets to the sides of the SMD2000-24T with the ten provided bracket screws. 2. Mount the chassis onto the rack and secure the rack mount brackets to the sides of...

Page 9 - Connect the other end of the ground wire to a frame ground.

9 Powering Up the SMD2000-24T C AUTION : Turn your DC power source off until you have completed connection of the SMD2000-24T as described below. Do not operate your SMD2000-24T without a ground connection. Procedure To connect the SMD2000-24T to power: 1. Connect a ground wire to the SMD2000-24T. L...

Page 10 - Attach the other ends of the power leads to a fuse panel.

10 The two terminal blocks on the SMD2000-24T are independent feeds. Chassis power is supplied by only one terminal block at a time; the second supply is merely backup. Likewise, the two terminal blocks do not load-share. Each terminal block must be supplied with the adequate amperage to run the cha...

Page 11 - Connecting the SHDSL RJ21 Cable

11 7. Verify the connection. Turn your power source ON. The PWR (power) LED on your SMD2000-24T faceplate will illuminate solid green to indicate that the chassis is receiving power. Connecting the SHDSL RJ21 Cable Procedure To connect the SHDSL cable to the SMD2000-24T RJ21 connector: 1. Configure ...

Page 12 - Connecting to the Remote SHDSL Modems; Loop Bonded SHDSL Connection

12 3. Slide the RJ21 plug connector of your SHDSL cable underneath the hook-and-loop fastener from the right and press it firmly into the RJ21 socket on the chassis. 4. Pull the hook-and-loop fastener strap upward, making sure that it is snug against the RJ21 connector, and then pull the strap back ...

Page 13 - Single Line SHDSL Connection

13 The speed and data passing capability of multiple SHDSL lines, as used for one network connection, is cumulative. For example, loop bonding three SHDSL lines for one network connection nets three times the speed and data passing capability of a single-line SHDSL connection. Additionally, use of m...

Page 14 - Connecting the Uplink Lines

14 Connecting the Uplink Lines To connect the SMD2000-24T to T1 service: 1. Configure the T1 uplinks. No configuration is necessary for the SMD2000-24T to operate at default settings. However, if you wish to run uplinks at settings other than the SMD2000-24T defaults, configure the uplinks prior to ...

Page 15 - Default Settings; SHDSL Parameter Defaults; Table 1. SHDSL Defaults

15 Default Settings SHDSL Parameter Defaults T1 Uplink Parameter Defaults Table 1. SHDSL Defaults Parameter Default Backbone-VLAN 0 (off) Circuit Identification n/a (no default) Flood Uplink IP Range 1 0.0.0.0 – 255.255.255.255 IP Range 2 0.0.0.0 – 0.0.0.0 Protocol All Speed 272 kbps VLAN Priority 0...

Page 17 - Data Storage; Memory; Table 6. Backup Criteria

17 Data Storage Configuration backup is inherent in the SMD2000-24T. Default parameters remain in place unless changed using the CLI, web management system, or SNMP. Memory Parameter configurations are automatically recorded in both Random Access Memory (RAM) and Non-Volatile Random Access Memory (N...

Page 18 - SHDSL Port Template

18 SMD2000-24T Template An SMD2000-24T template file records all management and port configurations except IP Address. SHDSL Port Template A SHDSL port configuration file records all of one port's configurations except Circuit ID. A previously saved port configuration file can be downloaded to multi...

Page 19 - System Reset

19 Reset Button The reset button is a small, unmarked button just to the right of the T1 uplink LEDs on the chassis faceplate. The button is recessed and you need a paper clip, mechanical pencil, or similar tool to press it. System Reset A system reset will clear all statistical data (stored in RAM)...

Page 20 - LED Indicators; State

20 Command Line Interface for 4000E and 12000E BACs, Micro DSLAMs, and Network Extenders User's Guide (Document Number CLI-A2-GB20) or the Network Management System User's Guide (Document Number NMS-A2-GB20) for further information. LED Indicators For purposes of the following descriptions, a pulsin...

Page 23 - Pin Assignments; SHDSL RJ21 Pinouts; Pins 25 and 50 are not used.; Table 10. SHDSL RJ21 Pinouts

23 Pin Assignments SHDSL RJ21 Pinouts Pins 25 and 50 are not used. Table 10. SHDSL RJ21 Pinouts Port Connector Pins (Ring, Tip) Port Connector Pins (Ring, Tip) Port 1 1, 26 Port 13 13, 38 Port 2 2, 27 Port 14 14, 39 Port 3 3, 28 Port 15 15, 40 Port 4 4, 29 Port 16 16, 41 Port 5 5, 30 Port 17 17, 42 ...

Page 24 - T1 RJ48C Pin Assignments

24 10/100BaseT RJ45 Pinouts T1 RJ48C Pin Assignments Table 11. Ethernet RJ45 Connection Pin Connection 1 Rx+ 2 Rx– 3 Tx+ 4 not used 5 not used 6 Tx– 7 not used 8 not used Table 12. T1 RJ48C Pin Assignments Pin Function Pin 1 Rx Ring Pin 2 Rx Tip Pin 3 not used Pin 4 Tx Ring Pin 5 Tx Tip Pin 6 not us...

Page 25 - DB9 to 8-Pin Modular Adapter Pinouts; Table 13. DB9 to 8-Pin Modular Adapter Pinouts

25 DB9 to 8-Pin Modular Adapter Pinouts To connect the COM port to the DB9 serial port of a PC, use an adapter wired as shown: Pins not shown are unused. Table 13. DB9 to 8-Pin Modular Adapter Pinouts Pin 8-Pin Modular Port Direction PC RS232 Serial Port Pin 1 Transmit Data TxD → RxD Receive Data 2 ...

Page 26 - Technical Specifications; Specification

26 Technical Specifications Table 14. SMD2000-24T Technical Specifications Specification Criteria Bandwidth and Distance Capabilities – SHDSL Ports Default is 272 kbps at up to 20,200 ft (6,157 m) Maximum distance is up to 24,000 ft (18,000 m) at 144 kbps Maximum bandwidth is 2320 kbps at up to 11,3...

Page 27 - EMI Notices; United States – EMI Notice; ACTA Customer Information; Facility Interface Codes Code Description

27 EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a...

Page 28 - CE Marking

28 A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. See installation instructions for details. If the network extender causes harm to the telephone network, the telephon...

Page 29 - Japan Notice; Class A ITE

29 Japan Notice Class A ITE This is a Class A product based on the standard of the Voluntary Control Council for interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be requir...

Page 30 - Important Safety Instructions; interconnecte

30 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and...