Paradyne Broadband Services Switch - Manuals

Page 3 - Product Documentation Online; Release Notes

BSX8-A2-GZ40-10 March 2005 3 BSX8000-5 Overview The BSX8000-5 Broadband Services Switch provides multi-gigabit Ethernet uplink support capability, full-nonblocking switching throughput, and enhanced management functionality for the 4000E and 12000E Broadband Loop Carriers (BLCs). The BSX8000-5 suppo...

Page 4 - Unpacking and Inspecting the Equipment; Procedure

4 March 2005 BSX8-A2-GZ40-10 Unpacking and Inspecting the Equipment HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, t...

Page 5 - Connect the MIM to the Network

BSX8-A2-GZ40-10 March 2005 5 Installing the BSX8000-5 in a BLC The 12000E is a 14-slot Broadband Loop Carrier (BLC). Slots 1–12 are reserved for access modules (such as the AIM24000-48) and slots U1 and U2 are reserved for uplink modules. Although not required for operational purposes, if redundancy...

Page 6 - BLC Management; Web Browser

6 March 2005 BSX8-A2-GZ40-10 MIM-4000F The MIM-4000F is a four-port fiber gigabit Ethernet interface connecting directly to the gigabit Ethernet switch in the BSX8000-5 uplink module. MIM-2E1 Plug your E1 cable into one of the RJ45 E1 ports on the MIM-2E1 faceplate. The MIM-2E1 connects to an E1 net...

Page 7 - Configuring Your Windows PC to Communicate with NMS

BSX8-A2-GZ40-10 March 2005 7 Configuring Your Windows PC to Communicate with NMS To communicate with NMS, your PC’s Ethernet interface must be on the same subnet as the BSX8000-5. For example, to configure the IP address under Windows XP: Procedure 1. In the Windows task bar, click on the Start butt...

Page 9 - NMS Management Configuration; Parameter

BSX8-A2-GZ40-10 March 2005 9 NMS Management Configuration Use the Management Configuration screen to set the unit’s IP address and other management parameters. Procedure To configure management parameters: 1. From the home screen, click on the Management Config button. The Management Configuration s...

Page 10 - CLI System Requirements; Straight-Through RJ45 to RJ45 Ethernet Cable –

10 March 2005 BSX8-A2-GZ40-10 3. Click on Submit. Command Line Interface (CLI) CLI System Requirements Straight-Through RJ45 to RJ45 Ethernet Cable – Required for establishing a direct connection from the COM port to a DB9 adapter. DB9 Female to RJ45 Male Adapter – Required for conversion of you...

Page 11 - Connecting a PC Directly; Launching the Terminal Emulation Program; Command

BSX8-A2-GZ40-10 March 2005 11 Connecting a PC Directly To connect a PC directly to the DSLAM to use the CLI: Procedure 1. Plug a DB9 to RJ45 adapter into the RS232 serial port on your PC. See DB9 to RJ45 Adapter Pinouts on page 14. 2. Connect one end of a straight-through RJ45 to RJ45 Ethernet cable...

Page 13 - LED Indicators; Table 2. LED States and Meanings

BSX8-A2-GZ40-10 March 2005 13 LED Indicators Table 2. LED States and Meanings LED State Indication Additional Information PWR (Power) Solid green BSX8000-5 uplink module is receiving power Both BLC power terminals are connected. Solid amber BSX8000-5 uplink module is receiving power Only one of the ...

Page 14 - DB9 to RJ45 Adapter Pinouts

14 March 2005 BSX8-A2-GZ40-10 10/100/1000BaseT Connectors The uplink ports are 8-pin unkeyed modular jacks for a 10/100/1000BaseT interface. The MGMT port is an 8-pin modular jack supporting 10/100BaseT. DB9 to RJ45 Adapter Pinouts To connect the COM port to the DB9 serial por t of a PC, use an adap...

Page 15 - Regulatory Compliance for Class A Equipment; US Federal Communications Commission (FCC); Europe

BSX8-A2-GZ40-10 March 2005 15 Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to a BSX8000-5 as installed in a Paradyne BLC. US Federal Communications Commission (FCC) NOTE: This equipment has been tested and found to comply with the limits for a C...