Paradyne 5620 RTU - Manuals

Page 2 - Package Checklist; What Does the Hotwire RADSL RTU Do?

2 Package Checklist Verify that your package contains the following: - Model 5620 Remote Termination Unit (RTU) - DSL interface cable with RJ11 connectors - Power cord with power transformer - Two ferrite chokes What Does the Hotwire RADSL RTU Do? The Hotwire 5620 RTU is a component in the Hotwire D...

Page 3 - DSL Access with a Hotwire 5038 Distributed POTS Splitter

3 98-16105 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Point Local Loop CP POTS Splitter DSL – Digital Subscriber Line POTS – Plain Old Telephone Service NID – Network Interface Device RTU – Remote Terminat...

Page 4 - DSL Access without a POTS Splitter; Network

4 DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter, a second telephonewiring pair is needed for DSL access. 97-15345-02 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) POTS DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) ...

Page 5 - Installing the DSL Access Wiring; Procedure; Important Safety; Punchdown Block

5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connectedfrom the customer premises side of the punchdown block or the NID to the DSL jack.Typically, the punchdown block is installed in commercial locations and the NID isinstalled in residen...

Page 7 - RJ11 Wall Jack; or; Wiring can be run from the

97-15300a RJ11 Wall Jack or 7 The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation pointto an RJ11 wall jack. The DSL twisted-pair wiring from the local loop terminates at anew or existing wall jack. It may be necessary to install a standard single RJ11 jack orreplace a si...

Page 8 - Installing the Hotwire 5620 RTU; Hotwire RTU; Customer

8 Installing the Hotwire 5620 RTU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Procedure 1. Use the supplied RJ11 6-pin interface cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jacklabele...

Page 11 - Optional RTU Wall Placement

11 Optional RTU Wall Placement The Hotwire 5620 RTU is designed for tabletop placement. The RTU can also bemounted on a wall. To mount an RTU, you will need: - Three slotted-head #6 self-threading screws with molly bolts - Drill and 3/16 I drill bit for the molly bolts - Screwdriver A template with ...

Page 12 - RTU Hardware Template

12 RTU Hardware Template Front(LEDs) 98-16171 5.43" 7.55" To Bottom Hole

Page 13 - Status LEDs; LED

13 Power-On When power is applied, the RTU performs self-diagnostics and the PWR LED is on.The self-diagnostics includes a power-on self-test. During the power-on self-test, all ofthe LEDs turn on for one second. TST DSL ETHERNET ALM PWR TM 98-15835 Power – green Alarm – red Test – yellow Digital Su...

Page 14 - Troubleshooting; LED Symptom; Increasing the Number of End-User Systems

14 Troubleshooting LED Symptom Action All LEDs are on. The RTU may be in download mode. Wait ten minutes. If LEDs remain on after ten minutes and the RTU is not indownload mode, the RTU is not functional. Contact the NSP. ALM LED remainson. The power-on self-test may have failed. Unplug the unit and...

Page 15 - Function

98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 15 Cables & Connectors Use standard twisted-pair CAT3 or better cables. This section is reference information. The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — To connect the RTU to an Ethernet hub, use the straight-throu...

Page 16 - Model 5620 RTU Technical Specifications; Item

98-15304-01 6-Pin RJ11 Plug DSLCable Pin #1 Pin #6 16 The DSL interface connector uses a 6-pin, non-keyed modular plug. RJ11 6-Pin Connector Pin # Function 1 & 2 Not used 3 DSL Ring 4 DSL Tip 5 & 6 Not used Model 5620 RTU Technical Specifications Item Specification * Height x Width x Depth 1...

Page 17 - Important Safety Instructions

17 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and...

Page 18 - Declaration of Conformity

18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2and 15 of the Federal Communications Commission’s Rules. This complianceinformation statement pertains to the following products: Trade Name: Hotwire Model Number: 5620-A2-200 This device c...

Page 19 - Canada EMI Warnings; To Users of Digital Apparatus in Canada:; Notice to Users of the Canadian Telephone Network

19 Canada EMI Warnings ! WARNING: To Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadianinterference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences durèglement sur le matérial brouilleur du Ca...

Page 20 - Visit the Paradyne World Wide Web site at; Trademarks

20 Warranty, Sales, and Service Information Contact your local sales representative, service representative, or distributor directly forany help needed. For additional information concerning warranty, sales, service, repair,installation, documentation, training, distributor locations, or Paradyne wo...