Paradyne 5216 - Manuals - manualsarea.com

Page 2 - Package Checklist; What Does the Hotwire RTU Do?; DSL Access with a POTS Splitter

2 Package Checklist Verify that your package contains the following: - Model 5216 Remote Termination Unit (RTU) - DSL interface cable with RJ11 modular plugs - Power cord with power transformer - Two ferrite chokes - Warranty card Refer to Cables & Connectors , page 13, for standard pin numbers....

Page 4 - DSL Access without a POTS Splitter; Network

4 DSL Access without a POTS Splitter When the 5216 RTU is installed without a POTS splitter, a second telephone wiring pairis needed for DSL access. 97-15609 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) POTS DSL Ethernet Crossover Cable Central Office (CO) Demarcation Point Local Loop ...

Page 5 - Installing the DSL Access Wiring; Procedure; Important Safety; Punchdown Block

5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connectedfrom the customer premises side of the punchdown block or the NID to the DSL jack.Typically, the punchdown block is installed in commercial locations and the NID isinstalled in residen...

Page 8 - DSL Jack Installation; o r

8 DSL Jack Installation The 5216 RTU connects to the local loop via wiring from the demarcation point to anRJ11 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new orexisting wall jack. It may be necessary to install a standard single RJ11 jack or replacea single jack with...

Page 9 - Installing the RTU; Hotwire RTU; Hotwire RTU

9 Installing the RTU Place the 5216 RTU on a flat surface with clearance for the rear connectors. " Procedure 1. Use the RJ11 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL. 97-15300-01 DSL Jack POWER...

Page 11 - Status LEDs; LED

11 6. Close the two halves around the cable and snap the ferrite choke shut. Press down on the plastic latch to secure the ferrite choke in place around the cable. 7. Plug the transformer into an AC outlet. The RTU hardware installation is now complete. When the power cord is installed, theRTU goes ...

Page 12 - ON; LED Symptom

12 LED Status Condition DSL Blinking ON OFF RTU is establishing the DSL link. The LED blinks on andoff about five times per second. The DSL link is now active and ready to transmit andreceive data. The DSL link has not been established. ETHERNET ON OFF The Ethernet 10BaseT connection to the end-user...

Page 13 - This section is reference information.; Function

97-15304 6 -P in R J 11 P lu g D S L L i n e P in # 1 P in # 6 13 LED Symptom Action DSL and EthernetLEDs are on andthere is no datatransmission. The DSL link and the Ethernet link have been established. Ifthe problem continues, contact the NSP. Ethernet LED is off. Verify that the Ethernet 10BaseT ...

Page 15 - Model 5216 RTU Technical Specifications; Item

15 Model 5216 RTU Technical Specifications Item Specification * Height x Width x Depth 1.35 ″ x 6.00 ″ x 8.75 ″ (3.43 cm x 15.35 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Class 2 Transformer normalservice input voltage range Input: 100 Vac, 50 Hz; 120 Vac, 60 Hz; or230 Vac, 50/60 Hz Output: ...

Page 16 - Important Safety Instructions

16 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and...

Page 17 - Class 2 ITE

17 CE Marking When the product is marked with the CE mark on the equipment label, thisdemonstrates full compliance with the following European Directives: H Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonizationof the laws of the member states relating to electrical equipme...

Page 18 - Declaration of Conformity

18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2and 15 of the Federal Communications Commission’s Rules. This complianceinformation statement pertains to the following products: Trade Name: Hotwire Model Number: 5216-A2-200 This device c...

Page 19 - EMI Warnings; To Users of Digital Apparatus in Canada:; Notice to Users of the Canadian Telephone Network

19 EMI Warnings ! WARNING: To Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadianinterference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences durèglement sur le matérial brouilleur du Canada. N...