Paradyne 4000E - Manuals

IPD4-A2-GZ40-10 July 2005 5 Installation in a Rack Using a Phillips Screwdriver, attach the two [2] provided rack mount brackets to the sides of the 4000E with eight [8] of the ten [10] provided bracket screws. There are seven position options for the rack brackets; position them as best suited to t...

6 July 2005 IPD4-A2-GZ40-10 Installing Your Management Module A management module provides the functional control for the 4000E BLC; the 4000E cannot function without one. There are several different models available for purchase. Refer to www.paradyne.com for further information, or contact your sa...

IPD4-A2-GZ40-10 July 2005 7 3. Slide the Management Module Firmly into the Chassis. Tighten the fastening screws on the management module faceplate. Installing Your Interface Module(s) Interface modules provide the subscriber connections for a 4000E BLC; up to four interface modules may be installed...

8 July 2005 IPD4-A2-GZ40-10 Procedure 1. Select a Slot for Installation. Although the 4000E is factory shipped with Slot 1 open, interface modules may be installed in any slot, 1–4. 2. Align the interface module with the slot module guides. With the interface module PCB facing up and the interface m...

IPD4-A2-GZ40-10 July 2005 9 Powering Up Your 4000E BLC CAUTION: Turn your DC power source(s) OFF until you have completed connection of the 4000E as outlined in the following sections. Do not operate the 4000E without a ground connection. Procedure 1. Connect a ground wire to the 4000E: Line up the ...

IPD4-A2-GZ40-10 July 2005 11 5. Remove the right-hand screw (labeled "–") from the same terminal block. Slide the ring terminal of your NEGATIVE lead around the shaft of the screw and inser t the screw into the same "–" terminal from which it was removed. 6. Connect both power leads ...

12 July 2005 IPD4-A2-GZ40-10 Uplink Connections No configuration is necessary for Uplink Interface Modules (UIMs) or Media Interface Modules (MIMs) installed on the management module in your 4000E to operate at default settings. However, if you wish to run your uplink connections at settings other t...

14 July 2005 IPD4-A2-GZ40-10 4. Pull the hook-and-loop fastener strap upward, making sure that it is snug against the connector, then pull the strap back down, such that the hook-and-loop fastener layers stick to one another across the top of the connector. 5. Tuck the tab at the end of the strap do...

IPD4-A2-GZ40-10 July 2005 15 Securing the Connecting Cables Position all connecting cables such that they will not become a tripping hazard or pull loose from the chassis; secure with cable ties or hook-and-loop fastener straps. Configuration and Management Although no configuration is necessary to ...

IPD4-A2-GZ40-10 July 2005 17 Specifications Product Documentation Online Complete documentation for Paradyne products is available at www.paradyne.com . Select Support → Technical Manuals . To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2...

18 July 2005 IPD4-A2-GZ40-10 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous high voltage points or oth...

IPD4-A2-GZ40-10 July 2005 19 — Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. — Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. — Use caution when installing or ...

20 July 2005 IPD4-A2-GZ40-10 CANADA – EMI NOTICE: ! This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur le matérial brouilleur du Canada. Warranty, Sales...