Paradyne 3811PLUS - Manuals

Page 2 - Equipment Support and Warranty on page 4.

2 June 1998 3980-A2-GZ41-20 information must be provided to the telephonecompany. 2. The Universal Service Order Code (USOC) for Permissive mode is RJ21X. The Canadianequivalent to the USOC is CA21A. 3. The Ringer Equivalence (REN) is used to determine the quantity of devices which may beconnected t...

Page 4 - Installation; Customer-Supplied Equipment

4 June 1998 3980-A2-GZ41-20 command line or from a directory. An occurrence of therestriction is canceled when a different number is dialed,or when three minutes have elapsed. Equipment Warranty andSupport Technical Support Contact your local sales representative, service representative, or distribu...

Page 5 - Plus Modem

5 3980-A2-GZ41-20 June 1998 496-14488-02 TXD RXD RTS CTS DSR DTR LSD 103 104 105 106 107 108 109 Pwr Alrm Test Dial RI Busy Serv SQ Status Front Panel 3811 Plus 142 125 Spkr Faceplate EIA232/V.24 Edge Card Connector EIA232/V.24 Connector Unused V .35 (3600/3500) RS366A/V .25 (3800) EIA232/V .24 Rear...

Page 6 - Procedure; At the rear of the carrier, install the rear connector; DTE Connectors; CAUTION; At the front of the carrier, hold the modem

6 June 1998 3980-A2-GZ41-20 The COMSPHERE 3000 Series Carrier has 17 slots which can hold up to 16 modems and one SDU. The SDUis required when the modems in the carrier are controlledby an NMS, or when multiple carriers in a cabinetconfiguration are to be controlled by a single SDCP. TheSDCP of the ...

Page 7 - Circuit; Check the SDCP

7 3980-A2-GZ41-20 June 1998 3. Rotate the circuit pack lock(s) into the closed position, and tighten the screw. Circuit Card Guides Circuit PackLock Latch Open (Unlocked) Closed (Locked) 495-14813 4. If the carrier is connected to power, the Power LED on the faceplate of the 3811Plus lights up.After...

Page 8 - Configuring a Modem Using the SDCP; Configuring a Modem Using AT Commands

8 June 1998 3980-A2-GZ41-20 Select Factory ConfigurationOptions After the modem passes the power-up self-test, configure it for operation using one of the factory presetconfigurations. The 3811Plus modem has several factory preset templates that contain the proper configuration options(straps) for d...

Page 9 - Where: n is one of the following Factory; Menu Structure

9 3980-A2-GZ41-20 June 1998 To change a factory template using AT commands, perform the following steps. Procedure 1. Enter the appropriate factory configuration command (&Fn) followed by the &W0 commandto store the configuration in Active (Saved) andthe Z command to reset the modem. TYPE: A...

Page 11 - Customer1

11 3980-A2-GZ41-20 June 1998 Configure Ld EditArea frm: Edit Save Choose Function Active (Saved) Customer1 Customer2 V42/MNP/BufferErr Contrl ModeSync Comp ModeSDC NegotiationSDC Idle FillSDC BitEncodingSyncDTE CRCSDC Delay MinSync Flow CntrlV42bis CompressMNP5 CompressEC Negotiat BfrEC Fallbck Char...

Page 12 - Copyright

12 June 1998 3980-A2-GZ41-20 Control Remote Speaker Reset Make_Busy or RemoveMakeBusy Service_Line or DiscServLine Download Code Secondary Prim (data blckd) (ExitRem appears instead of Remote when using Remote Mode) Does not appear in Remote Mode.(Rem_Digital_Loop, Loc_Digital_Loop, andPattern appea...