Palsonic 6138 - Manuals - manualsarea.com

Page 3 - OPERATING INSTRUCTION:

OPERATING INSTRUCTION: POWER ON/OFF SWITCH Press the Power Switch, the appliance will be in "STANDBY" mode. A red light shows onthe control panel. Press "PR-/+" buttons to turn on the set. The red light goes out, anda green light, shows on the control panel.If there is no TV signal o...

Page 4 - TUNING CHANNELS

There are two ways to choose the channel number you want-the single-number method andthe double-number method. Single-digit Method (highest Program Number is 9)This allows numbers 0 ~ 9 ONLY and is useful for limiting the number of channels if youdo not mind some channels on the wrong number (10 and...

Page 5 - STORE; CHANNEL STORE; PERSONAL PREFERENCE STORE

VHF-1 When the set finds a TV signal, it will stop searching automatically, and show the TVpicture on the screen. The tuning is optimised for strong signals. Weak signals may need finetuning for the best result. If you want another channel, press the SEARCH button again. The station may be fine-tune...

Page 7 - THE CONTROL OF PICTURE AND SOUND

Low (Left Speaker) THE CONTROL OF PICTURE AND SOUND Function selectOn the Front Panel, the "PICTURE" button is used to select the following functions:BRIGHTNESS, COLOUR, CONTRAST, BALANCE and VOLUME in that order. Eachof the functions is adjusted by means of the adjacent -/+ level control bu...

Page 8 - REMOTE CONTROL UNIT; Remove the battery cover of Remote Control Unit.

REMOTE CONTROL UNIT The remote control unit allows almost everything to be adjusted from the armchair. DIGITAL BUTTON 16 MUTE 9 VOLUME UP/DOWN 5 BRIGHTNESS UP/DOWN 2 PR (+/-) 6,7 RECALL 15 BATTERIES: 1. Remove the battery cover of Remote Control Unit. 2. Insert two "AA" 1.5V batteries making...

Page 9 - BUTTON LIST; TV FUNCTIONS; This button returns all other modes back to TV.

11. S.MPX (Stereo switching) BUTTON LIST The trick is to push the buttons slowly; it takes a moment to register. Be careful that thebutton does not lock down. Some buttons behave differently in TV and Teletext. The followinglist is grouped according to TV or Teletext. If the description of a button ...

Page 10 - LISTENING TO STEREO/DUAL-CHANNEL TV SOUND

16. DIGITAL BUTTON In single-digit mode, press these buttons to select any of 0~9 channels.In double-digit mode, press these buttons to select any of 00~39 channels. LISTENING TO STEREO/DUAL-CHANNEL TV SOUND The Model 6138 is fitted with full performance Stereo Theatre Sound where the internal speak...

Page 13 - CONNECTION DIAGRAMS; RECORDING FROM THE TV

NOTE:* You can use either RF or Audio/Video input from the VCR, but the quality of picture and sound is better using the Audio/Video sockets.* If the VCR has Mono sound, connect it to the L/Mono input socket. The R/Stereo cable is optional for Stereo and need not be used. CONNECTION DIAGRAMS 1. VIDE...

Page 14 - off during the session.

Press AV Button (13) to switch to Video mode. The TV set will act as a monitor to help edit while dubbing. The set MUST remain in Video mode and MUST NOT be switched off during the session. 3. DUBBING The figure below shows how to connect TWO VCRs to the TV for dubbing one from the other. 13

Page 15 - CONNECTING EXTERNAL SPEAKERS; Connect speaker leads

CONNECTING EXTERNAL SPEAKERS You can connect speakers to the EXTERNAL SPEAKER terminals on the TV set to enhance sound from the TV. Note: Before connecting the external speakers, turn off your TV set. While pressing the button, insert the wire into the hole as shown below, and then release the butto...

Page 16 - TROUBLE SHOOTING

TROUBLE SHOOTING Many apparent malfunctions may be caused by slight misadjustment of regular controls orsome other similar causes. If any difficulty arises in the operation of your set, firstcheck through this list of symptoms and correction. Should the difficulty cause concern,unplug the set and co...

Page 17 - Specifications

Specifications Colour System: Receivers Channel Cable Channel Stereo Power supply CRT Audio Output Antenna Impedance Dimension (mm) Weight Remote Control Unit Power Supply * Design and specifications are subject to change without notice. : CCIR PAL, B/G; NTSC PLAYBACK : VHFL 0-3; VHFH 4-11; UHF 21-6...

Page 18 - PALSONIC CUSTOMER SERVICE

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-64063-01