Palsonic 4890 - Manuals - manualsarea.com

Page 2 - Contents; Operation

Congratulations on your purchase of this Palsonic colour television receiver.We recommend that you thoroughly read this manual before use to fully enjoy themany functions and excellent effects of this receiver.Retain is manual in an easily accessible location for future reference. Contents Notes for...

Page 4 - ANTENNA CONNECTIONS; effective to obtain a clear-picture.

CONTROL PANEL REMOTE SENSOR POWER INDICATOR ANTENNA INPUT AV IN OUT 1. ANTENNA CONNECTIONS 1.1 Optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture. 1.2 Insert the out-door antenna into the antenna socket on the cabinet back. Adjust t...

Page 5 - MFT

3.1 STANDBY ( ) Button 3.1.1 Press STANDBY ( ) button to turn on the set (the indicator shows yellow) when the set is in STANDBY mode (the indicator shows red) , the channel position number is displayed in the screen. Press STANDBY ( ) button to return the set to the STANDBY mode when the set is in ...

Page 6 - CHANNEL SELECTION; llllllllllllll

3.2.2.4 Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position, 3.2.2.5 Repeat 1~ 4 steps to search another channel. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased.* ...

Page 8 - REMOTE CONTROL UNIT; matches the polarity marks inside the unit.

4. REMOTE CONTROL OPERATION: REMOTE CONTROL UNIT : STANDBY 1 ~ 9 : DIGITAL CHANNEL SELECTOR10/0 : CHANNEL 10 OR CHANNEL 0 SELECTORSYSTEM : COLOUR SYSTEM CONTROL -/- - : DIGIT OR TWO DIGIT CHANNEL SELECT : PREVIOUS 4.1 INSTALLING BATTERIES: 4.1.1 Remove the battery cover of Remote Control Unit. 4.1.2...

Page 9 - CHANNEL SELECTION

4.3 CHANNEL SELECTION 4.3.1 Press CHANNEL SELECTOR ( ) the channel number will be increased or decreased and displayed in the upper right corner of the screen. 4.3.2 Use the DIGITAL CHANNEL SELECTOR button for direct channel selection. 1) 1~10 channel Method 1: Example: To select channel 2 To select...

Page 10 - CONTRAST

6 5 4.3.3 PREVIOUS BUTTON Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach chann...

Page 12 - SLEEP; TIMER

4.8 SLEEP BUTTON 4. 8. 1 Using SLEEP button allows you to have the appliance automatically turned off after a pre-determined time, and set the appliance to STAND BY mode. 4. 8. 2 After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes. NOTE...

Page 13 - TIME SET

4.9.1 CLOCK 4.9.1.1 Press the TIMER button till "CLOCK" displays-on the screen. 4.9.1.2 Press the button to set the present hour. Press the button to set the present minute. 4.9.1.3 After setting the clock, press TIME SET button to start operating. Now the indication on the screen is green i...

Page 14 - AUTO; SYSTEM SELECTION; Press it again

AUTO 4.9.8.8 Press TIME SET button, then the OFF TIME indication is green instead of red. OFF TIME function starts operating. 4.9.8.4 The appliance will be turned off when your setting time is up, and return to stand by mode. NOTE: * The built-in clock employs the 24-hour system. * The OFF TIME func...

Page 17 - TROUBLE SHOOTING GUIDE

6. TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls orsome other equally similar simple causes. If any problem arises in the operation of your set, firstcheck through this list of symptoms and correction. Should the problem be unsettled, unp...

Page 19 - PALSONIC CUSTOMER SERVICE

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-51703-05