Northern Industrial 6237D - Manuals

Page 2 - SPECIFICATIONS

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. Model 6217D 6237D 6317D 6337D 6347D Capacities Steel 10 mm (3/8”) 13 mm (1/2”) Wood 25.4 mm (1”) 32 mm (1-1/4”) 25.4 mm (1”) 32 mm (1-1/4”) 38 mm (1-1/2”) ...

Page 3 - GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS; Work Area; Electrical Safety

3 GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/orserious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well l...

Page 4 - SPECIFIC SAFETY RULES

4 Tool Use and Care 12. Use clamps or other practical way tosecure and support the workpiece to astable platform. Holding the work by hand or against your body is unstable and may leadto loss of control. 13. Do not force tool. Use the correct tool foryour application. The correct tool will do the jo...

Page 9 - Tips for maintaining maximum battery life

9 NOTE: • The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries. • When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a no...

Page 10 - Speed change

10 Switch action CAUTION: • Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased. To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch...

Page 11 - Selecting action mode; Adjusting the fastening torque; ASSEMBLY

11 • Do not use the speed change lever while the tool isrunning. The tool may be damaged. Selecting action mode This tool has an action mode change lever. For drilling,depress the lock button and then slide the action modechange lever to the left ( symbol). For screwing, slide the action mode change...

Page 12 - Installing or removing driver bit or drill bit; OPERATION; Screwdriving operation

12 Installing or removing driver bit or drill bit Hold the ring and turn the sleeve counterclockwise to openthe chuck jaws. Place the bit in the chuck as far as it will go.Hold the ring firmly and turn the sleeve clockwise to tightenthe chuck. To remove the bit, hold the ring and turn the sleeve cou...

Page 13 - Drilling operation; Drilling in wood

13 • If the tool is operated continuously until the batterycartridge has discharged, allow the tool to rest for 15minutes before proceeding with a fresh battery. Drilling operation First, slide the action mode change lever to the position of symbol. Drilling in wood • When drilling in wood, the best...

Page 14 - MAINTENANCE; Replacing carbon brushes

14 • Always secure small workpieces in a vise or similar hold-down device. • If the tool is operated continuously until the batterycartridge has discharged, allow the tool to rest for 15minutes before proceeding with a fresh battery. MAINTENANCE CAUTION: • Always be sure that the tool is switched of...

Page 15 - Recycling the Battery; ACCESSORIES

15 EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it.The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. a) Take the battery to your nearest Makita Factory Ser-vice Center or b) Take the battery to ...

Page 16 - Memo

Page 18 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

18 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 19 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

19 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...

Page 20 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation of America

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...