NordicTrack NTSA03990 - Manuals

Page 3 - Important Precautions

3 WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.Read all instructions before using. ICON assumes no responsibility for personal injury or propertydamage sustaine...

Page 4 - Part Identification Chart—Model No. NTSA03990

4 3/8" x 2" Bolt (121) 3/8" Flat Washer (120) 1/4" x 3/4" Bolt (130) 3/8" Nylon Locknut (118) 3/8" x 3 1/4" Bolt (124) 3/8" x 2 3/4" Bolt (125) 3/8" Nylon Jam Nut (122) 5/8” x 1/4” Spacer (127) 1/4" x 1 1/2" Bolt (131) 3/8" x 3" Carriage Bo...

Page 5 - Assembly

5 Assembly Make sure you have the following tools: • Two adjustable wrenches • One rubber mallet • You will also need grease or petroleum jelly, a small amount of soapy water, and clear tape ormasking tape. Note: Assembly will be more convenient if you havea socket set, a set of open-end or closed-e...

Page 6 - Frame Assembly

6 2. Remove the inner cap and the four hole plugs fromthe end of the stabilizer. Secure the Base Support (103) to the stabilizer withtwo 3/8” x 2 3/4” Bolts (125), four 3/8” Washers (120),and two 3/8” Nylon Locknuts (118). Press the inner cap into the indicated end of the BaseSupport (103). 1. Befor...

Page 8 - Cable Assembly

8 10. Wrap the Cable (133) around a 4” Pulley (113) and attach the Pulley and a Cable Trap (116) to the PressFrame (101) with a 3/8” x 3 3/4” Bolt (110), a 3/8”Washer (120), and a 3/8” Nylon Locknut (118). Make sure that the Cable (133) is routed in thedirection shown. 11. Slide the end of the Cable...

Page 9 - Assembly Option A

9 13. Locate the Pulley Bracket (91), one 1/4” Flat Washer (71), and one 1/4” Nylon Locknut (25) that came withyour weight system. Attach the end of the Cable (133)to the Pulley Bracket with the Flat Washer and theNylon Locknut. 13 71 25 91 133 12. Wrap the Cable (133) around a 4” Pulley (113) and a...

Page 11 - Assembly Option B

11 13 13. Loosen the 1/2” Plain Nut (68) on the bolt at the end of the High Cable (73). Detach the bolt from the topof the Weight Tube (36) and the Long Bushing (76). Remove the 1 1/2” Flat Washer (40) and the LongBushing (76). Put them where you can easily findthem later. 14. Locate the Pulley Brac...

Page 12 - Seat and Plate Assembly

12 19. Attach the Backrest (134) to the Seat Frame (106) with four 1/4” x 3/4” Bolts (130). 18. Open the parts bag labeled “SEAT ASSEMBLY.” Attach the Seat (111) to the Seat Frame (106) withfour 1/4” x 3/4” Bolts (130). 19 130 134 18 111 130 106 106 20. Attach the Foot Press (107) to the Press Plate...

Page 15 - Exploded Drawing—Model No. NTSA03990

15 108 107 124 120 122 120 124 124 11 0 11 3 11 6 122 120 11 8 11 5 11 2 11 2 124 11 8 11 7 125 11 8 126 120 133 127 122 11 5 11 8 11 8 11 0 11 3 11 6 120 11 8 120 11 9 123 11 6 11 3 11 3 121 11 6 11 8 132 132 130 11 2 131 128 128 11 2 130 109 109 11 8 105 104 103 102 106 111 134 129 12 0 101 133 11...

Page 16 - Ordering Replacement Parts; Limited Warranty

Ordering Replacement Parts To order replacement parts, simply call our Customer Service Department toll-free at 1-888-825-2588, Mondaythrough Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-pared to give the following information: • The MODEL NUMB...