Nokia FPS-8 - Manuals

Nokia FPS-8 – Manual in PDF format online.

Manuals:

Manual

Manual Nokia FPS-8

Summary

Page 2 - Contents

2 (30) Contents Introduction ........................................................................................................................................................... 3 Glossary ...........................................................................................................

Page 3 - Introduction; Pictures in this document may differ from the actual.

3 (30) Introduction This is a user guide for installing service sw and phone programming in FPS-8 environment. This guide will help you with the installation and with the basic problem solving. NOTE! Pictures in this document may differ from the actual.

Page 4 - Glossary; See Bootstrap code

4 (30) Glossary Algorithm code Flash programming algorithm code. This code runs in the target system and it must support used Flash type and phone hw. The prommer box can contain several algorithm codes; each code supports one or more different Flash devices. E.g. u_intel.fia supports a number of In...

Page 5 - Overview

5 (30) 1 Overview FPS-8 is a programming device for DCT4 phones. When equipped with power supply module ACS-10 it can also be used for programming latest DCT-3 phones. Software for FPS-8 Prommer is delivered in one installation package file. When the new installation package is installed to the cont...

Page 6 - Contents of the Sales package; Pic 1 Contents of a FPS-8 sales package

6 (30) 2 Contents of the Sales package FPS-8 Sales package (0080321) contains following items: o FPS-8 FLASH prommer (0750123) o Power supply ACF-8 (0680032) o CDROM (contains user guide and install sw) (0774271) o FPS-8 activation sheet (9359289) o Cables: AXS-4 Serial Cable (connects to PC COM por...

Page 7 - Minimum PC hardware requirements; Processor Pentium 233 Mhz

7 (30) 3 Minimum PC hardware requirements o Processor Pentium 233 Mhz o RAM 64 MB o Needed disk space 50 - 100 MB o Supported Operating Systems: Windows 95 Windows 98 Windows NT 4.0 Windows 2000

Page 8 - Usage; Installations; Before anything can be done, some installations must be made:; Activation; Phoenix should be closed before running BoxActivation.exe.; Pic 2 BoxActivation Welcome screen

8 (30) 4 FPS-8 Usage For successful use of FPS-8 also pc sw is needed. All needed sw modules are supplied with the Phoenix software (Official service software for DCT-4) and with WinTesla sw (official service software for DCT3 phones). 4.1 SW Installations Before anything can be done, some installat...

Page 9 - Deactivation; Pic 3 Deactivation; FPS-8 Maintenance with Phoenix; Pic 4 FPS-8 sw update dialog

9 (30) 4.3 FPS-8 Deactivation If there is a need to send FPS-8 box to somewhere e.g. for repair, box must be first deactivated. FPS-8 can be deactivated with BoxActivation sw. Just select Deactivate when asked to choose function. Pic 3 Deactivation 4.4 FPS-8 Maintenance with Phoenix Select”FPS-8 / F...

Page 10 - Pic 5 FPS-8 maintenance UI; Phone programming with Phoenix; Phone is programmed by selecting “FPS-8 flash” from “Flashing” -menu

10 (30) All files can also be loaded separately to FPS-8. To do this, just press right mouse button in ”Flash box files” window and select file type to be loaded . Pic 5 FPS-8 maintenance UI More information and help can be found from dialogs help (press F1 or Help –button). 4.5 Phone programming wi...

Page 12 - Needed devices for DCT3 phone programming:

12 (30) 5 FPS-8 DCT3 setup Needed devices for DCT3 phone programming: o PC with WinTesla Service SW (Diskette Code 0774046) equipped with product specific support dlls. o FPS-8 FLASH prommer box (0750123) o DCT3 power supply module ACS-10 (0770340) o Power Supply ACF-8 (0680032) o Cables: AXS-4 Seri...

Page 15 - Pic 12 FPS-8 DCT4 environment

15 (30) 6 FPS-8 DCT4 setup Needed devices for DCT4 phone programming: o PC with Phoenix Service SW CD ROM Code (0775311) o Product specific data package o FPS-8 FLASH prommer box (0750123) o Power supply ACF-8 (0680032) o Cables: AXS-4 Serial Cable (Connects to PC COM port) (0730090) Centronics Cabl...

Page 16 - hardware; Phone service cable connector

16 (30) 7 FPS-8 hardware 7.1 FPS-8 Front panel FPS-8 front panel and LEDs are shown like they are when prommer is in normal mode. If everything is OK, prommer should be in this state after power is connected. Connectors: Phone service cable connector DCT-4 power output connectors for DCT-4 service b...

Page 17 - Phone connector; Pic 13 FPS-8 rear panel

17 (30) 7.2 FPS-8 rear panel (Without DCT3 power supply module ACS-10) Connectors: Parallel input (Centronics) Phone connector Serial input (RS232) PWR (power connector) Pic 13 FPS-8 rear panel

Page 18 - Pic 14 FPS-8 mainboard

18 (30) 7.3 FPS-8 main board Prommer main board has 8 MB SRAM and 16 MB Flash memory for MCU file storing. The mainboard has a socket for add-on memory modules: SRAM module SF12 (8 MBytes), 0080346 FLASH module SF13 (64 MBytes), 0080347 The mainboard has also a socket (Pic 24 DCT3 power supply modul...

Page 19 - modules; Additional SRAM and Flash modules can be plugged into the; Figure 1 Example of possible memory combinations

19 (30) 7.3.1 Memory modules Additional Memory modules are needed when bigger than 8MB files are needed program to the phone (more SRAM needed) or there is need to store several MCU files in to the FPS-8 (more flash memory needed). (SRAM module (8MB) SF12, 0080346 and FLASH module (64MB) SF13, 00803...

Page 20 - FPS-8 has to be powered off; when mounting memory modules or DCT-3; Pic 17 Memory extension connector

20 (30) 7.3.1.1 Memory module installation instructions NOTE! When opening the prommer box or installing power / memory modules all work should be done in an ESD – safe environment! Step1: power off FPS-8. FPS-8 has to be powered off when mounting memory modules or DCT-3 power supply ACS-10 module. ...

Page 23 - DCT3 power supply module ACS-10; Pic 22 DCT3 power supply module ACS-10 from inside

23 (30) 7.4 DCT3 power supply module ACS-10 If FPS-8 prommer box is wanted to be used for programming DCT3 phones, additional DCT3 power supply module ACS-10 is needed to provide correct current and voltage levels. FPS-8 add-on rear panel Pic 22 DCT3 power supply module ACS-10 from inside Pic 23 DCT...

Page 24 - DCT3 power supply module ACS-10 installation instructions; DCT3 power supply module ACS-10 will replace; when mounting memory modules or DCT-3

24 (30) 7.4.1 DCT3 power supply module ACS-10 installation instructions DCT3 power supply module ACS-10 will replace original rear panel . Step1: power off FPS-8. FPS-8 has to be powered off when mounting memory modules or DCT-3 power supply ACS-10 module. Mounting modules with power supply connecte...

Page 28 - Troubleshooting; Flash programming problems; -FPS-8 is activated with a wrong activation file; Other problems in operation; Although all cables are connected, FPS-8 seems not to be ON.

28 (30) 8 Troubleshooting 8.1 Flash programming problems Symptoms: Flashing fails when proper cables are not used between FPS-8 and phone. Possible error codes: many different errors during flash programming. Cure: Use only shielded cable between FPS-8 and phone (e.g. XCS-4, code 0730178) Symptoms: ...

Page 29 - Meaning of the LEDs in the front panel during startup

29 (30) 8.3 Meaning of the LEDs in the front panel during startup Disconnect all cables from FPS-8. Connect power plug to "POWER 5.5 - 8VDC" connector. Inspect the mode leds while FPS-8 is starting. The leds in the front panel should flash as follows: ON +------------------------------------...

Page 30 - What to do with malfunctioning FPS-8 devices

30 (30) 8.4 What to do with malfunctioning FPS-8 devices If trouble shooting does not help then fill in Repair Request Note, which comes with the sales package. NOTE! Deactivate box before sending. See 4.3 FPS-8 Deactivation.