Nikon SF-200 - Manuals - manualsarea.com

Page 2 - Cautions; permission has been obtained.; Trademark Information; The; The

18 Cautions • The reproduction of this manual in whole or in par t is prohibited save in cases in which Nikon’s prior permission has been obtained. • The information contained in this manual is subject to change without notice. • Nikon has made ever y effor t to produce a perfect manual, but should ...

Page 3 - Items prohibited by law from being copied or reproduced

19 Federal Communications Commission (FCC) Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Par t 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer...

Page 4 - A Note on Nikon Scan

20 1. Overview Thank you for your purchase of an SF-200 (S) slide feeder for 4000 ED (SUPER COOLSC AN 4000 ED)and LS-2000 (SUPER COOLSCAN 2000) Nikon film scanners. The SF-200 (S), which can hold up tofifty mounts 1.5 mm in thickness, automates the scanning of consecutive 35 mm slides. Like the othe...

Page 5 - Parts and Accessories

21 SF-200 (S) slide feeder (1) 2. Parts and Accessories This chapter lists the items packaged with your slide feeder and identifies the par ts of the SF-200 (S). 2.1 Package Contents Purchasers of the SF-200 (S) should find that the package contains all the items listed below. Should youfind that an...

Page 7 - be inser ted or removed while the status LED is blinking.; Status LED; The illustration shows the SUPER COOLSCAN 4000 ED

23 The SF-200 (S) can be mounted on the scanner whether the scanner is off or on and connected to acomputer. If the scanner is on, before mounting the feeder check that the status LED is glowing steadily.The SF-200 (S) should NOT be inser ted or removed while the status LED is blinking. The scanner ...

Page 8 - Loading the feeder; Load mark

24 Close the magazine cover. You are now ready to begin scanning. For details on automatic consecutivescanning of multiple slides, refer to the software reference manual. Slides can be loaded into the feed magazine up to the load mark. Do not attempt to fill the magazinepast this point. Once the fee...

Page 9 - from the magazine and that the last slide to be fed has been ejected.; par ts or are not of an even thickness may jam in the feeder.; Insertion guide

25 • Do not load slides in the feed magazine past the load mar k, as this may cause the feeder to jam.• Do not move the scanner while scanning is in progress.• Remove scanned slides from the ejection magazine before the magazine is full. Continuing scanning when there is no room left in the ejection...

Page 10 - The following mounts can be used only in restricted orientations:; Mount; The following mounts are known to cause jams:

26 Slide Mounts That Can Be Used in the SF-200 (S) • The following mounts have been tested and approved for use in the SF-200 (S): GEPE 3mm, GEPE 2mm, bonum, REVUE, AGFA system G, AGFA reflecta CS, Reflecta GR, Kaiser SR,hama fix, ROWI quickslide • The following mounts can be used only in restricted...

Page 11 - (Macintosh) folder in the folder to which you installed; Attachment Utility; icon to star t the attachment utility.; select a; Windows

27 4.2 Removing slides Slides will be sent to the ejection magazine after scanning. To remove slides from the ejection magazine,pull back the push plate and remove the slides. Slides must be removed before the ejection magazinefills up. 4.3 Using the Feed-Mechanism Attachment Thick mounts (over 2 mm...

Page 12 - to return the feed mechanism to its initial posi-; OK; position. You are now ready to begin scanning.; Caution; attachment

28 Open the SF-200 (S)’s magazine cover, pull back the feed push-plate to the end of its grove, and hookit in the notch so that it does not spring back to its original position. Click the double right-arrow button in the attachment utility to move the feed mechanism to where itis fully visible. If y...

Page 13 - What to do if the feeder jams; To use the attachment utility, open the; FDUtility; folder to which you installed Nikon Scan and double-click the; icon to star t the

29 4.5 What to do if the feeder jams If a jam occurs, open the magazine cover and remove the slides remaining in the feed and eject maga-zines. Pull back the feed push-plate and hook it in the notch so that it does not spring back to its originalposition. The method for resolving a jam depends on th...