Newcon Optik LAM 3 IR - Manuals

2 Carefully read all the instructions prior to use. Failure to obey the instructions will void the warranty ! INVISIBLE LASER RADIATION CLASS 3B LASER PRODUCT 830–860 nm 25 mW, 630-650 nm 8 mW. DON’T LOOK INTO THE BEAM! 1. Brief description LAM laser aimer/illuminator (hereinafter referred as LAM) i...

3 1. LAM 3IR APPEARANCE Fig. 1 — Front view 1 - Windage and elevation adjustment knobs, for Visible & IR aimer channel 2 - Windage and elevation adjustment knobs, for illuminator channel 3 – Housing 4 - IR aimer 5 - Visible red aimer 6 - Battery compartment cover 7 – Illuminator 8 - Illuminator ...

4 Fig. 2 — LAM rear view 11 - Bracket 12 - blocking ring 13 - mode switch 14 - low battery indicator 15 – high / low (working / training modes) power switch 16 - remote button connector 17 - windage adjustment knob, illuminator channel 11 17 16 15 14 13 12

6 OFF LAM is off R Visible aimer is on P IR aimer is on IL Illuminator is on ILP Both IR aimer and Illuminator are on BT Battery test The LED (14, Fig. 2) in BT mode indicates battery level: solid red LED means the battery charge is normal, if it is blinking - the battery must be replaced. IR channe...

7 High power mode is a health hazard! Lock switch (15, Fig.2) with blocking ring (12, Fig.2) when you do not intend using LAM in high power mode. Use filter with the Red Channel in the training mode LAM can be turned on either with a switch (13, Fig. 2) or with a remote control pressure switch, when...

9 2. DELIVERY SET Standard delivery set Quantity Laser aimer / illuminator LAM 3 IR with mount 1 Remote pressure switch 1 O-Ring 1 Soft case 1 Manual 1 Warranty card 1

11 4. OPERATION INSTRUCTIONS DANGER! THIS LASER EQUIPMENT IS HAZARDOUS FOR YOUR EYES!  Do not look into laser beam with naked eyes or through any optical device.  Do not point an active unit at highly reflective surfaces or towards other individuals or animals. Battery installation  Ensure the mo...

12 Mounting LAM on a weapon  Mount LAM on the Picatinny rail using the quick release lever mount (9, Fig. 1) so that the laser emission is directed towards the target;  If desired, connect the remote switch cable to the connector (16, Fig. 2) and tighten the nut. Fix the remote switch on the weapo...

13 1. Mount LAM on the weapon. 2. Fix the weapon in the aiming rest. 3. Insert the laser bore sight into the barrel. 4. Zero the bore sight in accordance with its operation manual. 5. Set the target at the distance, required for this weapon and this target. 6. Activate LAM in ILP mode. 7. Set minima...

14 4. Set the minimal divergence of the illuminator channel. 5. Superpose centers of the spots produced by the aimer and illuminator on the aiming mark by rotating adjustment knobs (1, Fig. 1), (17, Fig. 2). 6. Fire the weapon. 7. If point of impact is off the aiming mark adjust windage and elevatio...

15 Preparing LAM for transportation 1. Turn LAM off by turning operating modes switch (13, Fig. 2) to OFF position. 2. Disconnect the remote switch from the weapon. 3. Loosen quick release lever (9, Fig.1), remove LAM from Picatinny rail. 4. Pack LAM and remote switch into the case

16 5. CARE, STORAGE AND TRANSPORTATION General LAM is a sophisticated precise optical instrument equipped with electronics. Therefore, it should be handled with due care. - Never disassemble LAM. - Keep away from direct sunlight, impacts, dust, moisture, and sharp changes of temperature. - Do not st...

17 If LAM was exposed to salt water it should be rinsed in fresh water and dried outside at no more than 55 o C. Long-term storage When preparing for long-term storage, cover the external metal surfaces of LAM with protective lubricant. Each 4 (four) years old layer of lubricant should be removed an...

19 8. Presence of acid and alkaline vapor, as well as of other aggressive admixtures in the air in the storage area may cause damage to LAM. 9. After 4 years of storage, it is necessary to perform thorough inspection of units’ functionality. Transportation When packed, LAMs can be transported by any...

21 7. WARRANTY NEWCON warrants this product against defects in material and workmanship for one year from the date of the original purchase. Longer warranty is available, subject to the terms of the specific sales contract. Should your Newcon product prove to be defective during this period, please ...

24 10. QUALITY CERTIFICATE LAM 3 IR serial number_____________________________ complies with all technical specifications and has passed the inspection. Date of production: _________________________________ Quality Inspector: __________________________________ Quality Assurance Seal