NAD T 765 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INSTRUCTIONS

1. Read instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions sho...

Page 4 - THANK YOU FOR CHOOSING NAD.; For warranty information contact your local distributor.; TABLE OF CONTENTS; INTRODUCTION

THANK YOU FOR CHOOSING NAD. The T 765 A/V Receiver is a technologically advanced and highly capable product — yet we have invested great effort in making it simple and easy to use. The T 765 delivers a range of genuinely useful options for surround sound and stereo listening alike, using powerful di...

Page 5 - A second set of speaker terminals (Speakers B) for remote listening.; EASE OF USE

INTRODUCTION ABOUT THE T 765 Though the T 765 is among the most technically sophisticated A/V Receiver, we worked hard to make it one of the most musically transparent home-theater components available as well; this is what we mean by NAD’s “Music First” design philosophy. Here are just few examples...

Page 6 - GETTING STARTED; WHAT’S IN THE BOX; Packed with your T 765 A/V Receiver you will find; SAVE THE PACKAGING; INITIAL SETUP; Source; viewed in their native format or via Component Video OUT.

INTRODUCTION GETTING STARTED WHAT’S IN THE BOX Packed with your T 765 A/V Receiver you will find • An AM loop antenna • A FM ribbon-wire antenna with balun • A removable AC cable (if you wish, any IEC-standard AC cable of suitable wattage may be substituted). • The HTR 3 remote control with 4 (four)...

Page 7 - DEALING WITH HUM AND NOISE; Connect the speakers to the A/V Receiver only, and check for hum.

DEALING WITH HUM AND NOISE Hum and noise may sometimes prove a challenge in complex, multi-channel audio systems. Note these considerations to help prevent hum and noise problems: • Power all your system's audio component from AC outlets originating from the same circuit of your house wiring. As far...

Page 8 - • The rear panel POWER switch must be in the ON position for the Power; IDENTIFICATION OF CONTROLS; FRONT PANEL

1 POWER BUTTON : Press this button or the HTR 3 remote’s [ON] button to switch ON the T 765. The Standby LED indicator will turn from amber to blue and illuminate the VFD. Pressing the power button again turns the unit back to standby mode. The T 765 can also be switched ON from standby mode by pres...

Page 9 - 7 FRONT INPUT jacks :

11 SOURCE : Press these buttons to toggle through the input selections – Source 1, Source 2, Source 3, Source 4, iPod, Source 7, Front Input, Media Player and Tuner. More Sources could be directly recalled through these buttons upon enabling them at the Setup Menu (See the section ‘Source Setup’ at ...

Page 10 - NOTE; Connect; REAR PANEL

1 DIGITAL AUDIO IN (OPTICAL 1-3, COAXIAL 1-3) : Connect to the optical or coaxial S/PDIF-format digital output of sources such as CD or DVD players, HDTV or satellite tuners and other components. Coaxial and Optical digital input association is configurable via the Setup Menu. DIGITAL AUDIO OUT (OPT...

Page 13 - Press or ENTER to select a menu item. Use; MAIN MENU; LISTENING MODE; STEREO; OPERATION; USING THE T 765 – MAIN MENU

ABOUT THE ON-SCREEN DISPLAY (OSD) The T 765 receiver employs a simple, self-explanatory system of on-screen display “menus” that will appear on the connected video monitor/TV. These are required during the setup process (and are useful in day-to-day operation), so be sure to connect the monitor/TV b...

Page 15 - ADjUSTING LISTENING MODES; DSP OPTIONS

ADjUSTING LISTENING MODES Several of the T 765’s listening modes have one or more selectable variations and adjustable parameters that you can modify to suit you system or personal preferences. At Listening Mode menu, use a combination of ENTER and keys to navigate and effect desired settings. NOTE ...

Page 16 - ZONE CONTROLS; If a Zone is set to ‘Off,’ it is deactivated or powered off.

ZONE CONTROLS Depending on the settings made at the separate ‘Zone Setup’ menu under the ‘Setup Menu’ section discussion, the applicable Zone can be configured and managed via this ‘Zone Controls’ window. Select ‘On’ to activate the applicable Zone. When activated, the Source input for the particula...

Page 17 - SOURCE; USING THE T 765 – SETUP MENU

SETUP MENU The Setup Menu allows one to customize the operation of the T 765 to the ancillary equipment used in one’s specific AV system. Unless your system exactly matches the factory defaults as shown in the accompanying Quick Start Guide, you will need to use the setup menu to configure the input...

Page 19 - Scrolling to ‘A/V Preset’ and by pressing and then; TRIGGER OUT

ABOUT VIDEO FORMATS For many years, there was only one type of video format used. Composite video signals include the Luminance (black & White) and Chroma (color) signals combined on one wire. S-Video uses separate wires in a single cable for Luminance and Chroma signals. Component Video goes a ...

Page 20 - The following are the Speaker Setup Menu sections.; AUDYSSEY SETUP; The following measurements are performed:

SOURCE SETUP (TABLE VIEW) The Source Setup ( Table View) reflects the settings made in the Source Setup (Normal View) menu. All the Source settings are summarized and displayed in tabulated form in the Source Setup ( Table View). Navigating through the Source Setup ( Table View) via a combination of...

Page 21 - SPEAKER CONFIGURATION

MEASUREMENT IS THE FIRST STEP Connect the Audyssey microphone jack into the front panel’s MP/MIC input and the Audyssey Setup wizard will guide you through a simple step-by-step configuration. The sound at your main listening position is setup using the supplied Audyssey microphone. A special test t...

Page 23 - SPEAKER LEVELS; USING AN SPL METER; Use the remote’s; keys to adjust each speaker.; calibrate to exactly the same level offset readings.

SPEAKER LEVELS Adjusting the relative balance of your system’s loudspeakers ensures that surround-sound recordings, whether music or film, will present the balance of effects, music, and dialog that the artists intended. Additionally, if your system incorporates a subwoofer it establishes a correct ...

Page 24 - SPEAKER DISTANCE; SETTING SPEAKER DISTANCE; While at ‘Speaker Distance’ menu, use the; ADjUSTING THE VOLUME; In addition to the Volume knob, use the HTR 3’s VOL; MUTING THE SOUND; ADjUSTING CHANNEL LEVELS ‘ON THE FLY’

SPEAKER DISTANCE Your system’s speaker distance settings are a subtle but important refinement of your setup. Informing the T 765 of the loudspeaker-to-listener dimensions of each speaker automatically imposes the correct delays, optimizing imaging, intelligibility and surround-sound ambience. Enter...

Page 25 - ZONE SETUP; VOLUME; The ZR 4 remote control will only control Zone 2 applications.; AMPLIFIER SETUP

ZONE SETUP The Zone feature allows one to simultaneously experience in different zones of the house multiple sound and applicable video sources from all enabled Sources as well as from Front Input, Media Player and Tuner. The T 765 has three configurable Zones – Zone 2, Zone 3 and Zone 4. Use a comb...

Page 26 - TRIGGER SETUP; keys to navigate through the Trigger Setup; When the applicable Zone is at powered state, +12V DC is; DELAY; LISTENING MODE SETUP; keys to configure the following settings.; LISTENING MODES; the following settings – Pro Logic, PLIIx Movie, PLIIx Music or None.

TRIGGER SETUP The T 765 features three configurable +12V DC Trigger Output that can be used to activate a component or system it is fed into. A Trigger Input is also available to turn on the applicable link it is associated to. Use a combination of or ENTER and keys to navigate through the Trigger S...

Page 27 - DOLBY SETUP; Dynamic Range Control :; Please refer to the same description about ‘Adjusting Listening

DOLBY DIGITAL EX Using a Matrix decoder, this method creates the back channel (sometimes also called the “surround center”) by means of signals on the left and right surround channels recorded in Dolby Digital 5.1, reproduction being provided in Surround 6.1. This method should be selected with sour...

Page 28 - DTS SETUP; This is the same configurable Dynamic Range Control feature as; DTS SURROUND MODES

DTS SETUP Under this menu, the Dynamic Range Control of DTS Digital Surround can be adjusted as well as the settings for DTS Neo: 6 Music. Dynamic Range Control : This is the same configurable Dynamic Range Control feature as described above at Dolby Setup, the only difference being the soundtrack i...

Page 29 - DISPLAY SETUP

DISPLAY SETUP The Vacuum Fluorescent Display ( VFD) and On-Screen Display (OSD) can be shown in various ways by navigating through the parameters at the ‘Display Setup’ menu. Use a combination of or ENTER and keys to step through the ‘Display Setup’ menu items. NOTE The configurations set forth at ‘...

Page 30 - LISTENING TO RADIO; ABOUT ANTENNAS

LISTENING TO RADIO The T 765’s internal AM/FM tuner offers very high quality sound from radio broadcasts. The reception and sound quality will always be dependent to a degree however on the type of antenna(s) used as well as proximity to the broadcast origin, geography and weather conditions. ABOUT ...

Page 31 - ABOUT USER NAMES; NOTES; • Check with your NAD audio specialist for other versions of XM Mini-

CHOOSING THE TUNER MODE The front-panel ‘TUNER MODE’ key is a dual-purpose control. In the normal position, FM Mute FM Stereo icons on the VFD are illuminated, only the stations with a strong signal can be listened to, and the noise between stations is muted. Pressing the ‘TUNER MODE’ button again (...

Page 32 - ABOUT DAB RADIO; CONNECTING THE DAB MODULE; ABOUT iPod INPUT FEATURE; through T 765 may vary depending on your iPod player model.; NAVIGATING THE iPod PLAYER’S FUNCTIONS AND FEATURES; properly connected to the T 765 via the NAD docking station.; CONTROL FEATURES AND SETTINGS; Select [One] for repeated playback of the current song. Select; DISP

ABOUT DAB RADIO The T 765 has a Digital Audio Broadcast (DAB) module socket on the rear panel for adding a separately sold and NAD-specified outboard DAB module – the NAD DAB Adaptor DB 1. All the control software for this format is included; just plug-in the module and start enjoying the CD-like qu...

Page 33 - NAVIGATION BUTTONS; While at menu options or selection lists, toggle [; TO VIEW VIDEOS LOADED IN YOUR iPod

NAVIGATION BUTTONS During playback mode, press [ ] to skip forward to the next song or [ ] to skip back to the previous song. For quicker scrolling up or down the list, press and hold [ ]. While at menu options or selection lists, toggle [ ] to go up or down the options or lists. The equivalent fron...

Page 34 - SPECIFICATIONS; Controls up to 8 devices.; CONTROLLING THE T 765; USING THE HTR 3 REMOTE CONTROL

SPECIFICATIONS • Controls up to 8 devices. • 44 function keys. • Learns up to 352 commands. • Records up to 44 macros with a maximum of 64 commands each. • Configurable punch-through. • Key illumination with programmable timeout. • Upgradable. • Contains pre-programmed library of NAD remote codes. T...

Page 35 - LEARNING CODES FROM OTHER REMOTES; Learning “DVD Pause”; CANCEL OPERATION; PUNCH THROUGH; COPY A COMMAND FROM ANOTHER KEY; Copy the Pause command from the CD page to the AMP [ ] button:

LEARNING CODES FROM OTHER REMOTES Begin by positioning the HTR 3 “nose-to-nose” with the source remote so the two devices’ infrared windows are about 2 inches apart. • Enter Learning Mode: On the HTR 3, simultaneously press-and-hold for 3 seconds both a Device Selector key and the [RES] key (just be...

Page 36 - MACRO COMMANDS; Macros are independent of the currently selected device.; RECORDING MACROS; Commence Playback of connected Source 1 device (as in DVD player):; EXECUTING MACROS; BUTTON ILLUMINATION TIMEOUT

MACRO COMMANDS A “macro” command is a series of two or more remote codes issued automatically from a single keypress. You might use a macro to automate a simple command sequence, such as, “Turn on the DVD player and then press ‘play.’” Or you might compose an elaborate macro to power up an entire sy...

Page 37 - FACTORY RESET; DELETE MODE; Default Library Command

FACTORY RESET The HTR 3 can be reset to its factory state, deleting all learned commands, copied and punched-through keys, macros, and other setup information, reverting all keys to their pre-programmed library commands. To perform a factory reset simultaneously press-and-hold for 10 seconds the HTR...

Page 38 - LOADING CODE-LIBRARIES; HTR 3 code-library numbers; Tape Deck B; SEARCH MODE

LOADING CODE-LIBRARIES The HTR 3 can store a different library of default NAD codes for each of its Device Selector “pages.” If the original default library does not control your NAD CD player, tape deck, DVD player, or other component, follow the procedure below to change the code-library. Begin by...

Page 39 - CHECKING CODE-LIBRARY NUMBER; SUMMARY OF THE HTR 3 MODES; USING THE ZR 4 REMOTE CONTROL

CHECKING CODE-LIBRARY NUMBER You can check the current code-library on any Device Selector key as follows. Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired component’s Device Selector key and the [AVPS] key, until the Learn LED turns green. Press the [DISP] ke...

Page 40 - REFERENCE; TROUBLESHOOTING; CONDITION

REFERENCE TROUBLESHOOTING CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS No sound from all channels. AC power unplugged. • Check AC cable connection and outlet. • Power not switched on. • Outlet has no power. • Speaker A (or Speaker B) is not activated. • Activate Speaker A (or Speaker B) by pressing ...

Page 41 - AMPLIFIER SECTION; AM SECTION; PHYSICAL SPECIFICATIONS

REFERENCE SPECIFICATIONS AMPLIFIER SECTION Power output Stereo Mode 100W(20dBW ) (8 ohms within rated distortion) IHF dynamic power; 8 ohms 160W (22dBW ) IHF dynamic power; 4 ohms 270W (24.3dBW ) Power output Surround Mode 7 x 80W (19dBW ) Total harmonic distortion at rated power <0.05% IM distor...